Advertisement

Catalytic effects of shale ash with different particle sizes on characteristics of gas evolution from retorting oil shale

  • Xiang Ge
  • Sha WangEmail author
  • Xiumin Jiang
Article
  • 17 Downloads

Abstract

Huadian oil shale samples were pyrolyzed in a small retort at 520 °C in the absence and presence of shale ashes with different particle sizes of 0–0.20 mm, 0–0.60 mm and 0–1.25 mm under argon atmosphere to evaluate the catalytic effects of shale ash on the products yield and non-condensable gases evolution characteristics. The shale ash samples were recorded as 0.20 mm, 0.60 mm and 1.25 mm shale ashes. The results indicate that the shale ash samples with good adsorption capacity and certain catalytic performance significantly affect the reactivity of oil shale pyrolysis. There are a slight decrease in the shale char yield and an increase in the total yield of volatile products with the particle size of shale ash decreasing from 1.25 to 0.20 mm. The shale oil yield increases after adding 0.20 mm and 0.60 mm shale ashes, especially 0.20 mm, but decreases after adding 1.25 mm shale ash compared with that obtained without adding shale ash, while the non-condensable gases yield decreases after adding shale ashes with three particle sizes, especially 0.60 mm. In addition, the gas products contain higher-volume content of CO2, CH4 and H2, and lower-volume content of CO and C2–C4 hydrocarbons. Adding the shale ash makes the peak concentrations of all gases shift to the lower temperatures and increases the maximum peak concentrations of C4H8 and H2, especially H2, but decreases those of other gases. The non-condensable gases mainly contain CO2 and CH4, and smaller amounts of other gases in terms of their mass distribution. The addition of shale ashes reduces the yields of several gases except CO2, H2, C2H6 and C4H8 compared with those obtained without adding shale ash. Adding three shale ash samples increase the H2 content, but cause different effects on the contents of CO2, C2H6 and C4H8. Among three shale ash samples, adding 1.25 mm shale ash produces the largest amount of CO2 and CO, as well as the lowest total content of C2–C4 alkenes, while adding 0.60 mm shale ash produces the largest amount of H2 and largest total content of C1–C4 alkanes. Adding the shale ash decreases the ethene/ethane ratio and increases the other alkene/alkane ratios compared with those obtained without adding shale ash. Adding 0.2 mm shale ash among three shale ash samples produces the lowest ethene/ethane and propene/propane ratios, being possibly related to the most significant coking reactions. Adding shale ashes with smaller particle sizes are more conducive to obtain non-condensable gases of higher heating value. The addition of 0.20 mm shale ash is the optimal for improving the shale oil yield and the conversion rate of kerogen to volatile products.

Keywords

Oil shale retorting Shale ash Products yield Non-condensable gases Characteristics 

Notes

Acknowledgements

The authors express their gratitude to the State Key Laboratory of Heavy Oil Processing of China University of Petroleum for shale oil samples analysis and technical advice. This work was supported by the National Natural Science Foundation of China (Grant Nos. 50906051, 51704194), Young Teacher Training Scheme of Shanghai Universities (Grant No. ZZGCD15062) and the Research Start-up Fund from Shanghai University of Engineering Science (Grant No. 2015-52).

References

  1. 1.
    Dyni JR. Geology and resources of some world oil-shale deposits. Oil Shale. 2003;20(3):193–252.Google Scholar
  2. 2.
    Liu QQ, Han XX, Li QY, Huang YR, Jiang XM. TG–DSC analysis of pyrolysis process of two Chinese oil shales. J Therm Anal Calorim. 2014;116:511–7.Google Scholar
  3. 3.
    Tiwari P, Deo M. Compositional and kinetic analysis of oil shale pyrolysis using TGA–MS. Fuel. 2012;94:333–41.Google Scholar
  4. 4.
    Na JG, Im CH, Chung SH, Lee KB. Effect of oil shale retorting temperature on shale oil yield and properties. Fuel. 2012;95:131–5.Google Scholar
  5. 5.
    Dung NV. Factors affecting product yields and oil quality during retorting of Stuart oil shale with recycled shale: a screening study. Fuel. 1995;74:623–7.Google Scholar
  6. 6.
    Al-Harahsheh A, Al-Ayed O, Al-Harahsheh M, Abu-El-Halawah R. Heating rate effect on fractional yield and composition of oil retorted from El-lajjun oil shale. J Anal Appl Pyrol. 2010;89:239–43.Google Scholar
  7. 7.
    Maaten B, Loo L, Konist A, Siirde A. Mineral matter effect on the decomposition of Ca-rich oil shale. J Therm Anal Calorim. 2018;131:2087–91.Google Scholar
  8. 8.
    Li MY, Zhan JH, Lai DG, Tian Y, Liu XX, Xu GW. Study on the evolution characteristic of intermediate during the pyrolysis of oil shale. J Therm Anal Calorim. 2017;130:2227–38.Google Scholar
  9. 9.
    Wang S, Song LZ, Jiang XM. Prediction of gaseous products from Dachengzi oil shale pyrolysis through combined kinetic and thermodynamic simulations. J Therm Anal Calorim. 2018;134:1129–44.Google Scholar
  10. 10.
    Campbell JH, Kokinas GJ, Gallegos G, Gregg M. Gas evolution during oil shale pyrolysis. 1: nonisothermal rate measurements. Fuel. 1980;59(10):718–26.Google Scholar
  11. 11.
    Campbell JH, Gallegos G, Gregg M. Gas evolution during oil shale pyrolysis. 2. Kinetic and stoichiometric analysis. Fuel. 1980;59(10):727–32.Google Scholar
  12. 12.
    Huss EB, Burnham AK. Gas evolution during pyrolysis of various Colorado oil shales. Fuel. 1982;61(12):1188–96.Google Scholar
  13. 13.
    Marshall CP, Kannangara GSK, Wilson MA, Guerbois JP, Hartung-Kagi B, Hart G. Potential of thermogravimetric analysis coupled with mass spectrometry for the evaluation of kerogen in source rocks. Chem Geol. 2002;184(3–4):185–94.Google Scholar
  14. 14.
    Charlesworth JM. Oil shale pyrolysis. 2. Kinetics and mechanism of hydrocarbon evolution. Ind Eng Chem Process Des Dev. 1985;24(4):1125–32.Google Scholar
  15. 15.
    Wong CM, Crawford RW, Burnham AK. Determination of sulfur-containing gases from oil shale pyrolysis by triple quadrupole mass spectrometry. Anal Chem. 1984;56(3):390–5.Google Scholar
  16. 16.
    Reynolds JG, Crawford RW, Burnham AK. Analysis of oil shale and petroleum source rock pyrolysis by triple quadrupole mass spectrometry: comparisons of gas evolution at the heating rate of 10 °C/min. Energy Fuel. 1991;5(3):507–23.Google Scholar
  17. 17.
    Abbasi-Atibeh E, Yozgatligil A. A study on the effects of catalysts on pyrolysis and combustion characteristics of Turkish lignite in oxy-fuel conditions. Fuel. 2014;115:841–9.Google Scholar
  18. 18.
    Karabakan A, Yürüm Y. Effect of the mineral matrix in the reactions of oil shales: 1. Pyrolysis reactions of Turkish Göynük and US Green River oil shales. Fuel. 1998;77(12):1303–9.Google Scholar
  19. 19.
    Sadiki A, Kaminsky W, Halim H, Bekri O. Fluidised bed pyrolysis of Moroccan oil shales using the hamburg pyrolysis process. J Anal Appl Pyrol. 2003;70(2):427–35.Google Scholar
  20. 20.
    Floess JK, Plawsky J, Longwell JP, Peters WA. Effects of calcined dolomite on the fluidized bed pyrolysis of a Colorado oil shale and a Texas lignite. Ind Eng Chem Process Des Dev. 1985;24(3):730–7.Google Scholar
  21. 21.
    Ellig DL, Lai CK, Mead DW, Longwell JP, Peters WA. Pyrolysis of volatile aromatic hydrocarbons and n-heptane over calcium oxide and quartz. Ind Eng Chem Process Des Dev. 1985;24(4):1080–7.Google Scholar
  22. 22.
    Bakr MY, Yokono T, Sanada Y, Akiyama M. Role of pyrite during the thermal degradation of kerogen using in situ high-temperature ESR technique. Energy Fuel. 1991;5(3):441–4.Google Scholar
  23. 23.
    Gai RH, Jin LJ, Zhang JB, Wang JY, Hu HQ. Effect of inherent and additional pyrite on the pyrolysis behavior of oil shale. J Anal Appl Pyrolysis. 2014;105:342–7.Google Scholar
  24. 24.
    Hascakir B, Babadagli T, Akin S. Experimental and numerical simulation of oil recovery from oil shales by electrical heating. Energy Fuel. 2008;22(6):3976–85.Google Scholar
  25. 25.
    Hascakir B, Akin S. Recovery of turkish oil shales by electromagnetic heating and determination of the dielectric properties of oil shales by an analytical method. Energy Fuel. 2010;24(1):503–9.Google Scholar
  26. 26.
    Feng J, Xue XY, Li XH, Li WY, Guo XF, Liu K. Products analysis of Shendong long-flame coal hydropyrolysis with iron-based catalysts. Fuel Process Technol. 2015;130:96–100.Google Scholar
  27. 27.
    Jiang HF, Song LH, Cheng ZQ, Chen J, Zhang L, Zhang MY, Hu MJ, Li JN, Li JF. Influence of pyrolysis condition and transition metal salt on the product yield and characterization via Huadian oil shale pyrolysis. J Anal Appl Pyrolysis. 2015;112:230–6.Google Scholar
  28. 28.
    Williams PT, Chishti HM. Two stage pyrolysis of oil shale using a zeolite catalyst. J Anal Appl Pyrolysis. 2000;55(2):217–34.Google Scholar
  29. 29.
    Williams PT, Chishti HM. Influence of residence time and catalyst regeneration on the pyrolysis–zeolite catalysis of oil shale. J Anal Appl Pyrolysis. 2001;60(2):187–203.Google Scholar
  30. 30.
    Fan C, Yan JW, Huang YR, Han XX, Jiang XM. XRD and TG-FTIR study of the effect of mineral matrix on the pyrolysis and combustion of organic matter in shale char. Fuel. 2015;139:502–10.Google Scholar
  31. 31.
    Shi WJ, Wang Z, Song LW, Li XY. Pyrolysis of Huadian oil shale under catalysis of shale ash. J Anal Appl Pyrolysis. 2017;123:160–4.Google Scholar
  32. 32.
    Karabakan A, Yürüm Y. Effect of the mineral matrix in the reactions of shales. Part 2. Oxidation reactions of Turkish Göynük and US Western Reference oil shales. Fuel. 2000;79:785–92.Google Scholar
  33. 33.
    Yürüm Y, Kramer R, Levy M. Interaction of kerogen and mineral matrix of an oil shale in an oxidative atmosphere. Thermochim Acta. 1985;94(2):285–93.Google Scholar
  34. 34.
    Liu XS. Experiment analysis of the catalysis function of shale ash in fluidized retorting of oil shale solid heat carrier. Guang Dong Chem Ind. 2013;40(4):38–40 (in Chinese, with English abstract).Google Scholar
  35. 35.
    Shi WJ, Wang Z, Duan Y, Li SG, Song WL. Influence of shale ash on pyrolytic behaviors of oil shale. Chin J Process Eng. 2015;15(2):266–71 (in Chinese, with English abstract).Google Scholar
  36. 36.
    Oja V, Elenurm A, Rohtla I, Tali E, Tearo E, Yanchilin A. Comparison of oil shales from different deposits: oil shale pyrolysis and co-pyrolysis with ash. Oil Shale. 2007;24(2):101–8.Google Scholar
  37. 37.
    Niu MT, Wang S, Han XX, Jiang XM. Yield and characteristics of shale oil from the retorting of oil shale and fine oil-shale ash. Appl Energy. 2013;111:234–9.Google Scholar
  38. 38.
    Huang L, Zhang YM, Zhang L, Zhang XC, Sun GG. Effects of shale ash and FCC catalysts on adjusting secondary reactions of volatiles in oil shale pyrolysis. CIESC J. 2017;68(10):3770–8 (in Chinese, with English abstract).Google Scholar
  39. 39.
    Dung NV. Pyrolysis of Stuart oil shale in the presence of recycled shale. Fuel. 1990;69(4):497–501.Google Scholar
  40. 40.
    Carter SD, Taulbee DN, Robl TL. The relative coke-inducing tendencies of pyrolysed, gasified and combusted Devonian oil shales. Fuel. 1993;72(6):851–4.Google Scholar
  41. 41.
    Carter SD, Citiroglu M, Gallacher J, Snape CE, Mitchell S, Lafferty CJ. Secondary coking and cracking of shale oil vapours from pyrolysis or hydropyrolysis of a Kentucky Cleveland oil shale in a two-stage reactor. Fuel. 1994;73(9):1455–8.Google Scholar
  42. 42.
    Ballice L. Effect of demineralization on yield and composition of the volatile products evolved from temperature-programmed pyrolysis of Beypazari (Turkey) oil shale. Fuel Process Technol. 2005;86(6):673–90.Google Scholar
  43. 43.
    Han XX, Jiang XM, Cui ZG. Studies of the effect of retorting factors on the yield of shale oil for a new comprehensive utilization technology of oil shale. Appl Energy. 2009;86(11):2381–5.Google Scholar
  44. 44.
    Wang S, Jiang XM, Han XX, Tong JH. Effect of retorting temperature on product yield and characteristics of non-condensable gases and shale oil obtained by retorting Huadian oil shales. Fuel Process Technol. 2014;121(1):9–15.Google Scholar
  45. 45.
    Wang S, Wang Q, Jiang XM, Han XX, Ji HS. Compositional analysis of bio-oil derived from pyrolysis of seaweed. Energy Convers Manag. 2013;68:273–80.Google Scholar
  46. 46.
    Włodarzyk-Stasiak M, Jamroz J. Specific surface area and porosity of starch extrudates determined from nitrogen adsorption date. J Food Eng. 2009;93:379–85.Google Scholar
  47. 47.
    Yan JM, Zhang QY, Gao JZ. Adsorption and agglomeration. Beijing: Science & Technology Press; 1979. p. 118–23.Google Scholar
  48. 48.
    Zdravkov BD, Čermák JJ, Šefara M, Janků J. Pore classification in the characterization of porous materials: a perspective. Cent Eur J Chem. 2007;5(2):383–95.Google Scholar
  49. 49.
    Donohue MD, Aranovich GL. Adsorption hysteresis in porous solids. J Colloid Interface Sci. 1998;205(1):121–30.Google Scholar
  50. 50.
    Al-Qodah Z. Adsorption of dyes using shale oil ash. Water Res. 2000;34(17):4295–303.Google Scholar
  51. 51.
    Joseph JT, Forrai TR. Effect of exchangeable cations on liquefaction of low rank coals. Fuel. 1992;71(1):75–80.Google Scholar
  52. 52.
    Lu ST, Ruth E, Kaplan IR. Pyrolysis of kerogens in the absence and presence of montmorillonite-I. The generation, degradation and isomerization of steranes and triterpanes at 200 and 300 °C. Org Geochem. 1989;14(5):491–9.Google Scholar
  53. 53.
    Taulbee DN, Seibert ED. Comparison of the hydrocarbon pyrolysis products from a Devonian type II kerogen to those from kerogen/mineral blends. Energy Fuel. 1987;1(6):514–9.Google Scholar
  54. 54.
    Dembicki H, Horsfield B, Ho TTY. Source rock evaluation by pyrolysis-gas chromatography. AAPG Bull. 1983;67(7):1094–103.Google Scholar
  55. 55.
    Horsfield B, Douglas AG. The influence of minerals on the pyrolysis of kerogens. Geochim Cosmochim Acta. 1980;44(8):1119–31.Google Scholar
  56. 56.
    Torels N, Veryklos XE, Grossmann E. Catalytic effects of transition metals on oil shale pyrolysis. Ind Eng Chem Process Des Dev. 1986;25:552–7.Google Scholar
  57. 57.
    Greenfelder BS, Voge HH, Good GM. Catalytic and thermal cracking of pure hydrocarbons: mechanisms reaction. Ind Eng Chem. 1949;41(11):2573–82.Google Scholar
  58. 58.
    Hershkowitz F, Olmstead WN, Rhodes RP, Rose KD. Molecular mechanism of oil shale pyrolysis in nitrogen and hydrogen atmospheres. Am Chem Soc Symp. 1983;28(1):301–16.Google Scholar
  59. 59.
    Johns WD. Clay minerals and petroleum-forming reactions during burial and diagenesis. AAPG Bull. 1972;56(11):2160–7.Google Scholar
  60. 60.
    Williams PT, Nazzal JM. Polycyclic aromatic compounds in shale oils: influence of process conditions. Environ Technol. 1998;19(8):775–87.Google Scholar
  61. 61.
    Williams PT, Ahmad N. Influence of process conditions on the pyrolysis of Pakistani oil shales. Fuel. 1999;78(6):653–62.Google Scholar
  62. 62.
    Raley JH. Monitoring oil shale retorts by off-gas alkene/alkane ratios. Fuel. 1980;59(6):419–24.Google Scholar

Copyright information

© Akadémiai Kiadó, Budapest, Hungary 2019

Authors and Affiliations

  1. 1.Institute of Thermal Energy and Power Engineering, College of Mechanical EngineeringShanghai University of Engineering ScienceShanghaiPeople’s Republic of China
  2. 2.Institute of Thermal Energy Engineering, School of Mechanical EngineeringShanghai Jiao Tong UniversityShanghaiPeople’s Republic of China

Personalised recommendations