Advertisement

Properties and microstructure of Sn–0.7Cu–0.05Ni lead-free solders with rare earth Nd addition

  • Shuang Liu
  • Song-bai XueEmail author
  • Su-juan Zhong
  • Ying-ying Pei
  • Hua-wei Sun
Article
  • 29 Downloads

Abstract

The effects of rare earth Nd on the melting behavior, wettability, microstructure and mechanical properties of Sn–0.7Cu–0.05Ni solders have been investigated in this paper. The melting temperature was found to be slightly influenced with rare earth Nd addition. Results of wetting balance tests showed that adding a proper amount of Nd could substantially improve the wettability of Sn–Cu–Ni solders by decreasing the wetting time and increasing the wetting force. The morphology evolution of solder matrix indicated that Nd contributed to the refinement and uniformity of the microstructure when added within an appropriate range. It was because the fine NdSn3 particles formed primarily in the soldering process would act as heterogeneous nucleation sites during solidification. However, excessive addition of Nd was inadvisable due to the formation of large amounts of brittle and hard NdSn3 compounds with bulk shapes. Meanwhile, moderate amount of rare earth Nd could inhibit the growth of interfacial (Cu,Ni)6Sn5 IMCs during soldering. Results of micro-joints strength test also discovered that Sn–Cu–Ni–Nd soldered joints possessed sounder shear strength, which resulted from the refined microstructure and the improved solders/Cu interfacial morphology. These above results evaluated that the optimum content of Nd added into Sn–0.7Cu–0.05Ni solders was about 0.06 wt%.

Notes

Acknowledgements

This project was supported by National Natural Science Foundation of China (Grant No. 51675269) and by the State Key Laboratory of Advanced Brazing Filler Metals & Technology (Zhengzhou Research Institute of Mechanical Engineering), China (Grant No. SKLABFMT201704). This work was also supported by A Project Funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD).

References

  1. 1.
    S. Chada, Topics in lead-free solders: interfacial and Sn Whisker growth. J. Miner. Met. Mater. Soc. 64(10), 1174–1175 (2012)Google Scholar
  2. 2.
    L.L. Gao, S.B. Xue, L. Zhang et al., Effect of alloying elements on properties and microstructures of SnAgCu solders. Microelectron. Eng. 87(11), 2025–2034 (2010)Google Scholar
  3. 3.
    S.M. Hayes, N. Chawla, D.R. Frear, Interfacial fracture toughness of Pb-free solders. Microelectron. Reliab. 49(3), 269–287 (2009)Google Scholar
  4. 4.
    H. Ma, J.C. Suhling, A review of mechanical properties of lead-free solders for electronic packaging. J. Mater. Sci. 44(5), 1141–1158 (2009)Google Scholar
  5. 5.
    N. Zhao, X.Y. Liu, M.L. Huang et al., Characters of multicomponent lead-free solders. J. Mater. Sci. 24(10), 3925–3931 (2013)Google Scholar
  6. 6.
    G. Zeng, S.B. Xue, L. Zhang et al., Properties and microstructure of Sn–0.7Cu–0.05Ni solder bearing rare earth element Pr. J. Mater. Sci. 22(8), 1101–1108 (2011)Google Scholar
  7. 7.
    L. Zhang, S. Xue, L.L. Gao et al., Development of Sn–Zn lead-free solders bearing alloying elements. J. Mater. Sci. 21(1), 1–15 (2010)Google Scholar
  8. 8.
    S.K. Seo, S.K. Kang, D.Y. Shih et al., The evolution of microstructure and microhardness of Sn–Ag and Sn–Cu solders during high temperature aging. Microelectron. Reliab. 49(3), 288–295 (2009)Google Scholar
  9. 9.
    S. Liu, S.B. Xue, P. Xue et al., Present status of Sn–Zn lead-free solders bearing alloying elements. J. Mater. Sci. 26(7), 4389–4411 (2015)Google Scholar
  10. 10.
    H. Nishikawa, J.Y. Piao, T. Takemoto, Interfacial reaction between Sn-0.7Cu (-Ni) solder and Cu substrate. J. Electron. Mater. 35(5), 1127–1132 (2006)Google Scholar
  11. 11.
    T. Ventura, C.M. Gourlay, K. Nogita et al., The influence of 0–0.1 wt% Ni on the microstructure and fluidity length of Sn-0.7Cu-xNi. J. Electron. Mater. 37(1), 32–39 (2008)Google Scholar
  12. 12.
    T. Ventura, S. Terzi, M. Rappaz et al., Effects of Ni additions, trace elements and solidification kinetics on microstructure formation in Sn-0.7Cu solder. Acta Mater. 59(10), 4197–4206 (2011)Google Scholar
  13. 13.
    L. Zhang, L. Tian, Y.H. Guo et al., Wettability of SnCuNi-xEu solders and mechanical properties of solder joints. J. Rare Earths 32(12), 1184–1188 (2014)Google Scholar
  14. 14.
    Japanese Industrial Standards Committee, JIS Z 3198-4:2003. Test methods for lead-free solders-part 4: methods for wettability test by a wetting balance method and a contact angle method (2003)Google Scholar
  15. 15.
    Japanese Industrial Standards Committee, JIS Z 3198-7: 2003. Test methods for lead-free solders-part 7: methods for shear test of solder joints on chip components (2003)Google Scholar
  16. 16.
    J.X. Wang, S.B. Xue, Z.J. Han et al., Effects of rare earth Ce on microstructures, solderability of Sn–Ag–Cu and Sn–Cu–Ni solders as well as mechanical properties of soldered joints. J. Alloys Compd. 467(1–2), 219–226 (2009)Google Scholar
  17. 17.
    C. Yu, J.Y. Liu, H. Lu et al., First-principles investigation of the structural and electronic properties of Cu6−xNixSn5 (x = 0, 1, 2) intermetallic compounds. Intermetallics 15(11), 1471–1478 (2007)Google Scholar
  18. 18.
    L.L. Gao, S.B. Xue, L. Zhang et al., Effect of praseodymium on the microstructure and properties of Sn3.8Ag0.7Cu solder. J. Mater. Sci. 21(9), 910–916 (2010)Google Scholar
  19. 19.
    T. Laurila, V. Vuorinen, M. Paulasto-Kröckel, Impurity and alloying effects on interfacial reaction layers in Pb-free soldering. Mater. Sci. Eng. 68(1–2), 1–38 (2010)Google Scholar

Copyright information

© Springer Science+Business Media, LLC, part of Springer Nature 2018

Authors and Affiliations

  1. 1.College of Materials Science and TechnologyNanjing University of Aeronautics and AstronauticsNanjingPeople’s Republic of China
  2. 2.State Key Laboratory of Advanced Brazing Filler Metals & TechnologyZhengzhou Research Institute of Mechanical EngineeringZhengzhouPeople’s Republic of China

Personalised recommendations