Advertisement

Journal of Materials Science

, Volume 54, Issue 11, pp 8727–8742 | Cite as

Discharge and densification in the spark plasma sintering of quasicrystal particles

  • Ruitao LiEmail author
  • Qing Liu
  • Lihui Tian
  • Yun Wang
  • Khiam Aik Khor
  • Di Zhang
  • Zhili DongEmail author
Metals
  • 92 Downloads

Abstract

To investigate the micromechanisms involved in the spark plasma sintering of quasicrystals, thin foils were extracted from samples by focused ion beam at the interrupted states and analysed by transmission electron microscopy for the first time. Material jets are present between adjacent particles, indicating the occurrence of discharge/plasma. Surficial material melts first due to discharge and the liquid sputters as a result of the action of electric field, forming material jets. Discharge occurs in all the cavities with the largest gap size of 60 nm. Gap size is a deciding factor for the formation of material jets: Thick jets are only formed in narrow gaps (< 20 nm), while very thin jets or even no jets are present in wide gaps (> 20 nm). A low voltage (< 0.016 V) is needed to trigger the discharge, and it is inferred that quantum tunnelling and thermal excitation promote the formation of discharge within nanopores at relatively high temperatures. Discharge contributes very little to the densification, while the plastic deformation, meditated by a unique type of defect—metadislocations, is the dominant mechanism for it. The phase transformation of icosahedral Al–Cu–Fe–Cr to its crystalline approximants is accompanied by the formation of planar faults.

Notes

Acknowledgements

This project was supported by the Ministry of Education, Singapore (AcRF Tier 1, Grant No. RG93/16), and the National Natural Science Foundation of China (Grant No. 51575245). The TEM observation was performed at the Facility for Analysis, Characterization, Testing and Simulation (FACTS) in Nanyang Technological University, Singapore.

References

  1. 1.
    Shechtman D, Blech I, Gratias D, Cahn JW (1984) Metallic phase with long-range orientational order and no translational symmetry. Phys Rev Lett 53(20):1951–1953CrossRefGoogle Scholar
  2. 2.
    Levine D, Steinhardt PJ (1984) Quasicrystals - A new class of ordered structures. Phys Rev Lett 53(26):2477–2480CrossRefGoogle Scholar
  3. 3.
    Tanaka R, Ohhashi S, Fujita N, Demura M, Yamamoto A, Kato A, Tsai AP (2016) Application of electron backscatter diffraction (EBSD) to quasicrystal-containing microstructures in the Mg–Cd–Yb system. Acta Mater 119:193–202CrossRefGoogle Scholar
  4. 4.
    Kamiya K, Takeuchi T, Kabeya N, Wada N, Ishimasa T, Ochiai A, Deguchi K, Imura K, Sato NK (2018) Discovery of superconductivity in quasicrystal. Nat Commun 9(1):154CrossRefGoogle Scholar
  5. 5.
    Dubois JM (2012) Properties- and applications of quasicrystals and complex metallic alloys. Chem Soc Rev 41(20):6760–6777CrossRefGoogle Scholar
  6. 6.
    Köster U, Liu W, Liebertz H, Michel M (1993) Mechanical properties of quasicrystalline and crystalline phases in Al–Cu–Fe alloys. J Non-Cryst Solids s153–154(93):446–452CrossRefGoogle Scholar
  7. 7.
    Dubois JM (2000) New prospects from potential applications of quasicrystalline materials. Mater Sci Eng A 294:4–9CrossRefGoogle Scholar
  8. 8.
    Tian Y, Huang H, Yuan G, Ding W (2015) Microstructure evolution and mechanical properties of quasicrystal-reinforced Mg–Zn–Gd alloy processed by cyclic extrusion and compression. J Alloys Compd 626:42–48CrossRefGoogle Scholar
  9. 9.
    Garces G, Medina J, Pérez P, Máthis K, Horváth K, Stark A, Schell N, Adeva P (2018) Influence of quasicrystal I-phase on twinning of extruded Mg–Zn–Y alloys under compression. Acta Mater 151:271–281CrossRefGoogle Scholar
  10. 10.
    Coury FG, Botta WJ, Bolfarini C, Kiminami CS, Kaufman MJ (2015) Reassessment of the effects of Ce on quasicrystal formation and microstructural evolution in rapidly solidified Al–Mn alloys. Acta Mater 98:221–228CrossRefGoogle Scholar
  11. 11.
    Saito Y, Chen HS, Mihama K (1986) Icosahedral quasicrystal produced by gas evaporation of an Al–Mn alloy. Appl Phys Lett 48(9):581–583CrossRefGoogle Scholar
  12. 12.
    Salimon AI, Shevchukov AP, Stepashkin AA, Tcherdyntsev VV, Olifirov LK, Kaloshkin SD (2017) Mechanical alloying as a solid state route for fabrication of Al–Cu–M(= Fe, Cr) quasicrystalline phases. J Alloys Compd 707:315–320CrossRefGoogle Scholar
  13. 13.
    García-Escorial A, Lieblich M (2018) Atomization of Al-rich alloys: three paradigmatic case studies. J Alloys Compd 762:203–208CrossRefGoogle Scholar
  14. 14.
    Lee G, Olevsky EA, Manière C, Maximenko A, Izhvanov O, Back C, Mckittrick J (2017) Effect of electric current on densification behavior of conductive ceramic powders consolidated by spark plasma sintering. Acta Mater 144:524–533CrossRefGoogle Scholar
  15. 15.
    Cho J, Li J, Li Q, Ding J, Wang H, Xue S, Holland TB, Mukherjee AK, Wang H, Zhang X (2018) In-situ high temperature micromechanical testing of ultrafine grained yttria-stabilized zirconia processed by spark plasma sintering. Acta Mater 155:128–137CrossRefGoogle Scholar
  16. 16.
    Joo SH, Kato H, Jang MJ, Moon J, Kim EB, Hong SJ, Kim HS (2017) Structure and properties of ultrafine-grained CoCrFeMnNi high-entropy alloys produced by mechanical alloying and spark plasma sintering. J Alloy Compd 698:591–604CrossRefGoogle Scholar
  17. 17.
    Tian LH, Xiong W, Liu C, Lu S, Fu M (2016) Microstructure and wear behavior of atmospheric plasma-sprayed AlCoCrFeNiTi high-entropy alloy coating. J Mater Eng Perform 25(12):1–9CrossRefGoogle Scholar
  18. 18.
    Han QG, Chen ML, Zhang Q, Sun LS, Lin J, Wang LM (2015) Properties of Ti40.83 Zr40.83 Ni18.34 quasicrystalline alloys sintered by Spark Plasma Sintering. J Alloys Compd 650:154–158CrossRefGoogle Scholar
  19. 19.
    Trzaska Z, Couret A, Monchoux JP (2016) Spark plasma sintering mechanisms at the necks between TiAl powder particles. Acta Mater 118:100–108CrossRefGoogle Scholar
  20. 20.
    Ramond L, Bernard-Granger G, Addad A, Guizard C (2010) Sintering of a quasi-crystalline powder using spark plasma sintering and hot-pressing. Acta Mater 58(15):5120–5128CrossRefGoogle Scholar
  21. 21.
    Dong C, Dubois JM (1991) Quasicrystals and crystalline phases in Al65Cu20Fe10Cr5 alloy. J Mater Sci 26(6):1647–1654.  https://doi.org/10.1007/BF00544677 CrossRefGoogle Scholar
  22. 22.
    Li XZ, Dong C, Dubois JM (1995) Structural study of crystalline approximants of the Al–Cu–Fe–Cr decagonal quasicrystal. J Appl Crystallogr 28(2):96–104CrossRefGoogle Scholar
  23. 23.
    Hulbert DM, Anders A, Andersson J, Lavernia EJ, Mukherjee AK (2009) A discussion on the absence of plasma in spark plasma sintering. Scr Mater 60(10):835–838CrossRefGoogle Scholar
  24. 24.
    Zhang ZH, Liu ZF, Lu JF, Shen XB, Wang FC, Wang YD (2014) The sintering mechanism in spark plasma sintering—proof of the occurrence of spark discharge. Scr Mater 81(11):56–59Google Scholar
  25. 25.
    Guillon O, Gonzalez-Julian J, Dargatz B, Kessel T, Schierning G, Räthel J, Herrmann M (2014) Field-assisted sintering technology/spark plasma sintering: mechanisms, materials, and technology developments. Adv Eng Mater 16(7):830–849CrossRefGoogle Scholar
  26. 26.
    Roche S, Laissardière GTD, Mayou D (1997) Electronic transport properties of quasicrystals. J Math Phys 38(4):1794–1822CrossRefGoogle Scholar
  27. 27.
    Groza JR, Garcia M, Schneider JA (2001) Surface effects in field-assisted sintering. J Mater Res 16(1):286–292CrossRefGoogle Scholar
  28. 28.
    Chaim R (2007) Densification mechanisms in spark plasma sintering of nanocrystalline ceramics. Mater Sci Eng A 443(1):25–32CrossRefGoogle Scholar
  29. 29.
    Zou Y, Kuczera P, Sologubenko A, Sumigawa T, Kitamura T, Steurer W, Spolenak R (2016) Superior room-temperature ductility of typically brittle quasicrystals at small sizes. Nat Commun 7:12261CrossRefGoogle Scholar
  30. 30.
    Heggen M, Houben L, Feuerbacher M (2010) Plastic-deformation mechanism in complex solids. Nat Mater 9(4):332–336CrossRefGoogle Scholar
  31. 31.
    Korte-Kerzel S, Schnabel V, Clegg WJ, Heggen M (2018) Room temperature plasticity in m-Al13Co4 studied by microcompression and high resolution scanning transmission electron microscopy. Scr Mater 146:327–330CrossRefGoogle Scholar
  32. 32.
    Wollgarten M, Saka H, Inoue A (1999) Microstructural investigation of the brittle-to-ductile transition in Al–Pd–Mn quasicrystals. Philos Mag A 79(9):2195–2208CrossRefGoogle Scholar
  33. 33.
    Huttunen-Saarivirta E (2004) Microstructure, fabrication and properties of quasicrystalline Al–Cu–Fe alloys: a review. Cheminform 35(11):154–178CrossRefGoogle Scholar
  34. 34.
    Audier M, Guyot P, Brechet Y (1990) High-temperature stability and faceting of the icosahedral Al–Fe–Cu phase. Philos Mag Lett 61(2):55–62CrossRefGoogle Scholar
  35. 35.
    Munir ZA, Anselmi-Tamburini U, Ohyanagi M (2006) The effect of electric field and pressure on the synthesis and consolidation of materials: a review of the spark plasma sintering method. J Mater Sci 41(3):763–777.  https://doi.org/10.1007/s10853-006-6555-2 CrossRefGoogle Scholar
  36. 36.
    Singh A, Guo JQ, Tsai AP (2007) Stability and diffraction features of quasicrystal and 2/1 approximant phase in an Au42In42Yb16 alloy. Mater Sci Eng A 449–451:991–994CrossRefGoogle Scholar
  37. 37.
    Li RT, Dong ZL, Khor KA (2016) Spark plasma sintering of Al–Cr–Fe quasicrystals: electric field effects and densification mechanism. Scr Mater 114:88–92CrossRefGoogle Scholar
  38. 38.
    Holland TB, Löffler JF, Munir ZA (2004) Crystallization of metallic glasses under the influence of high density dc currents. J Appl Phys 95(5):2896–2899CrossRefGoogle Scholar
  39. 39.
    Friedman JR, Garay JE, Anselmi-Tamburini U, Munir ZA (2004) Modified interfacial reactions in Ag–Zn multilayers under the influence of high DC currents. Intermetallics 12(6):589–597CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media, LLC, part of Springer Nature 2019

Authors and Affiliations

  1. 1.School of Mechanical EngineeringJiangsu UniversityZhenjiangChina
  2. 2.School of Materials Science and EngineeringNanyang Technological UniversitySingaporeSingapore
  3. 3.Temasek Laboratories @ NTUResearch Techno PlazaSingaporeSingapore
  4. 4.National Demonstration Center for Experimental Materials Science and Engineering EducationJiangsu University of Science and TechnologyZhenjiangChina
  5. 5.School of Mechanical and Aerospace EngineeringNanyang Technological UniversitySingaporeSingapore
  6. 6.State Key Laboratory of Metal Matrix CompositesShanghai Jiao Tong UniversityShanghaiChina

Personalised recommendations