Advertisement

Cluster Computing

, Volume 22, Supplement 3, pp 6855–6864 | Cite as

Sensorless cluster based neural-fuzzy control strategy for four quadrant operation of three phase BLDC motor with load variations

  • S. BagavathyEmail author
  • P. Maruthupandi
Article
  • 107 Downloads

Abstract

Brushless DC (BLDC) motors are, in fact, a type of permanent magnet synchronous motors with a very high level of efficiency. An attempt has been made in this research work to design and implement four quadrant control of a BLDC motor drive with regenerative braking in either direction with a Position sensor less neural-fuzzy controller. The complete closed loop system being speed-controlled, four quadrant operation has been obtained using step speed input while the suitability of the developed model has been tested under full load stress during steady state. The results obtained satisfy the four quadrant operation requirements of advanced drives where controlled starts and stops are essential in both forward and reverse directions. This is evident in the effectiveness of current and torque tracking and ease of speed transition from motoring to regeneration and vice versa. The design simulation of four quadrant control of the BLDC motor is carried out using MATLAB. A simulink model is developed to simulate and analyze the operation of the motor. A permanent magnet synchronous machine with trapezoidal back EMF is modeled as a BLDC machine. The developed model finds applications in advanced industrial drives as an energy-efficient and cost-effective alternative to eliminate the effects of supply voltage drops and mechanical load variations.

Keywords

Sensor-less Fuzzy-neural BLDC Motor Load Variations Voltage Drops 

References

  1. 1.
    Lu, H., Zhang, L., Qu, W.: A new torque control method for torque ripple minimization of BLDC motors with un-ideal back-EMF. IEEE Trans. Power Electron. 23(2), 950–958 (2008)CrossRefGoogle Scholar
  2. 2.
    Rajagopalan, S.: Detection of rotor and load faults in brushless DC motors operating under stationary and nonstationary condition. Dr thesis, Georgia Institute of Technology (2006)Google Scholar
  3. 3.
    Rahman, N.B.: Neural network controller for DC motor using MATLAB application. BS thesis, University of Malaysia Pahang (2008)Google Scholar
  4. 4.
    Jung, S., Kim, S.S.: Hardware implementation of a real-time neural network controller with a DSP and a FPGA for nonlinear systems. IEEE Trans. Ind. Electron. 54(1), 265–271 (2007)CrossRefGoogle Scholar
  5. 5.
    Tang, K.S., Man, K.F., Chen, G., Kwong, S.: An optimal fuzzy PID controller. IEEE Trans. Ind. Electron. 48(4), 757–765 (2001)CrossRefGoogle Scholar
  6. 6.
    Shi, Y., Eberhart, R., Muhammed Zakariah, K.: A modified particle swarm optimizer. In: Proceedings of the IEEE International Conference on Evolutionary Computation, pp. 69–73 (1998)Google Scholar
  7. 7.
    Ozturk, S.B., Toliyat, H.A.: Sensorless direct torque and indirect flux control of brushless DC motor with non-sinusoidal back-EMF. IEEE Int. Ind. Electron. 3, 1373–1378 (2008)Google Scholar
  8. 8.
    Shanmugasundram, R., Muhammed Zakariah, K., Yadaiah, N.: Digital Implementation of fuzzy logic controller for wide range speed control of brushless DC motor. In: IEEE International Conference, pp. 119–124 (2009)Google Scholar
  9. 9.
    El-Samahy, A.A., El-Sharkawi, M.A., Sharaf, S.M.: Adaptive multi-layer self-tuning tracking control for DC brushless motors. IEEE Trans. Energy Convers. 9, 311–316 (1994)CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media, LLC, part of Springer Nature 2018

Authors and Affiliations

  1. 1.Department of Electrical and Electronics EngineeringSri Krishna College of Engineering and TechnologyCoimbatoreIndia
  2. 2.Department of Electrical and Electronics EngineeringGovernment College of TechnologyCoimbatoreIndia

Personalised recommendations