Advertisement

Cluster Computing

, Volume 22, Supplement 3, pp 5305–5313 | Cite as

The characteristic coefficient analysis of the pressure curve type based on the classification method

  • Yameng Wang
  • Huanfang LiuEmail author
Article
  • 77 Downloads

Abstract

Perforated pipes are widely used in applications such as drainage, irrigation and ventilation. The variation in the pressure head, h, in a perforated pipe follows a certain pattern. By analyzing h variation patterns at the tail ends of perforated pipes on flat slope, and the characteristic coefficient of the perforated pipe was proposed. According to the value of characteristic coefficient of the perforated pipe, perforated pipes are classified into three types, namely, short, medium and long pipes. In addition, a method for determining the type of perforated pipe based on its characteristic coefficient and length-to-diameter ratio is provided. Furthermore, on the condition of long perforated pipe, based on the locations of the maximum and minimum h values, the slope at which the perforated pipe is laid and the head loss ratio along the length of the perforated pipe, h curves are classified into five types. The experimental results demonstrate that the experimental data exhibit a variation pattern consistent with that of the calculation results, indicating that the classification of pressure head curves is, to a certain degree, reasonable and applicable.

Keywords

Perforated pipe Characteristic coefficient Pressure head Pressure curve type Extreme pressure points Classification of perforated pipes 

Notes

Acknowledgements

This study was financially supported by the National Natural Science Foundation of China under Grant Nos. 11362019 and 11562018.

References

  1. 1.
    Sheikholeslami, M., Gorji Bandpy, M., Ganji, D.D.: Experimental study on turbulent flow and heat transfer in an air to water heat exchanger using perforated circular-ring. J. Exp. Therm. Fluid Sci. 70(1), 185–195 (2016)CrossRefGoogle Scholar
  2. 2.
    Abida, H., Sabourin, J.F.: Grass swale-perforated pipe systems for stormwater management. J. Irrig. Drain. Eng. 132(1), 55–63 (2006)CrossRefGoogle Scholar
  3. 3.
    Nouri-Borujerdi, A., Seyyed-Hashemi, M.: Numerical analysis of thermally developing turbulent flow in partially filled porous pipes. J. Sci. Iran. Trans. B Mech. Eng. 22(3), 835–843 (2015)Google Scholar
  4. 4.
    Tang, J.: Hydraulic calculation of perforated outlet pipe of secondary sedimentation tank. J. Jishui Paishui/Water Wastewater Eng. 25(1), 21–23 (1999). Retrieved from https://search.proquest.com/docview/17908236?accountid=45196
  5. 5.
    Abida, H., Sabourin, J.F., Ellouze, M.: Model for the analysis of grass swale-perforated pipe systems. J. Irrig. Drain. Eng. 133(3), 211–221 (2007)CrossRefGoogle Scholar
  6. 6.
    Shen, P.I.: The effect of friction on flow distribution in dividing and combining flow manifolds. J. Fluids Eng. 114(1), 121–123 (1992)MathSciNetCrossRefGoogle Scholar
  7. 7.
    Graber, D.: Manifold flow in pressure distribution systems. J. Pipeline Syst. Eng. Pract. 3(1), 120–126 (2010)CrossRefGoogle Scholar
  8. 8.
    Zhang, G.X.: Method of determining locations of branch pipe on slope with paired capillaries in micro-irrigation system. J. Trans. Chin. Soc. Agric. Eng. 28(21), 98–104 (2012)Google Scholar
  9. 9.
    Zheng, C., Wu, P.T., Zhu, D.L., Zhang, L., Wang, J., Zhang, G.C.: Research on Flow Resistance and Pressure Head Distribution of perforated pipes Pipeline. J. Water Sav. Irrig. 03, 24–29 (2014)Google Scholar
  10. 10.
    Chang, F.S., Zhang, D.S.: Discussion on uniformity of drip irrigation. J. Water Resour. Hydropower Northeast China 12, 38–39 (2003)Google Scholar
  11. 11.
    Jin, J., Liu, H.F., Wang, Y.M.: The flow calculation on the porous pipe. J. China Rural Water Hydropower 2, 150–153 (2017)Google Scholar
  12. 12.
    Zhang, G.P., Fu, H., Yang, K.L., Zhao, L.M., Wang, M.W.: Characteristics of pressure distribution along perforated drain-pipe in siphon well. J. South-to-North Water Transf. Water Sci. Technol. 1, 186–192 (2017)Google Scholar
  13. 13.
    Du, T., Liu, H.F., Jin, J., Li, Q., Han, Y.C.: Study on the law of outflow and head variation of perforated pipe. J. Water Sav. Irrig. 2(8), 10–13 (2014)Google Scholar
  14. 14.
    Du, T., Liu, H.F., Jin, J., Li, Q., Wang, L.: Pressure distribution characteristics of perforated pipe outflow along pipeline. J. Chem. Eng. China 9, 48–52 (2014)Google Scholar
  15. 15.
    Afrin, T., Khan, A.A., Kaye, N.B., et al.: Numerical model for the hydraulic performance of perforated pipe underdrains surrounded by loose aggregate. J. Hydraul. Eng. 142(8), 04016018 (2016)CrossRefGoogle Scholar
  16. 16.
    Afrin, T., Kaye, N.B., Khan, A.A., et al.: Parametric study of perforated pipe underdrains surrounded by loose aggregate. J. Hydraul. Eng. 142(12), 04016066 (2016)CrossRefGoogle Scholar
  17. 17.
    Murphy, P.: The hydraulic performance of perforated pipe underdrains surrounded by loose aggregate. M.S. thesis, Clemson University, vol. 5, pp. 1–69 (2013)Google Scholar
  18. 18.
    Ravikumar, V., et al.: Analytical equation for variation of discharge in drip irrigation laterals. J. Irrig. Drain. Eng. 129(4), 295–298 (2003)CrossRefGoogle Scholar
  19. 19.
    Liu, H.F., Sun, H.Y., Su, P.: Determination of optimal laying length of gravitational flexible hose for micro-irrigation. J. Trans. Chin. Soc. Agric. Eng. 21(2), 46–50 (2005)Google Scholar
  20. 20.
    Zhang, T.J., Wu, F., Deng, Z., Fan, Y.S.: Experimental study on effect of pressure on capillary tube uniformity in drip irrigation at different slopes. J. Adv. Sci. Technol. Water Resour. 27(3), 24–26 (2007)Google Scholar
  21. 21.
    Maynes, D., Holt, G.J., Blotter, J.: Cavitation inception and head loss due to liquid flow through perforated plates of varying thickness. J. Fluids Eng. 135(3), 031302 (2013)Google Scholar
  22. 22.
    Wang, J.Y., Ge, X.L., Li, H.L., et al.: Flow characteristics of multiple-hole pipe for turbine condenger—uniform flow distribution. In: C. Sponsored by Chinese Society of Power Engineering, Proceedings of CSPE-JSME-ASME International Conference on Power Engineering, Shanghai, China, pp. 22–26, pp. 754–758 (1995)Google Scholar
  23. 23.
    Zhu, D.L., Wu, P.T., Zhang, L.: Calculation method of the maximum flow variation and evaluation of factors for micro-irrigation engineering. J. Drain. Irrig. Mach. Eng. 4, 340–344 (2013)Google Scholar
  24. 24.
    JU, X.L., WU, P.T., Weckler, R.P., ZHANG, L., ZHU, D.L.: Appropriate layouts of micro-irrigation laterals laid on uniformly sloping ground. J. Trans. Chin. Soc. Agric. Mach. 5, 123–128 (2016)Google Scholar
  25. 25.
    CHANG, H.H., Li, Y.: Research on pressure head distribution and allowed maximum length of orifice outlet drip irrigation laterals. J. China Rural Water Hydropower 1, 41–44 (2014)Google Scholar
  26. 26.
    Hong Xing, L.V.: The Hydraulics, pp. 130–151. China Agriculture Press, Beijing (2002)Google Scholar

Copyright information

© Springer Science+Business Media, LLC 2017

Authors and Affiliations

  1. 1.College of Water Conservancy and Architecture EngineeringShihezi UniversityShiheziChina

Personalised recommendations