Photocatalytic and magnetic porous cellulose macrospheres for water purification
- 65 Downloads
In this work, we report the preparation of photocatalytically active and easy to recycle porous cellulose-based spheres from polymer solutions in ionic liquid/dimethylsulfoxide mixtures by using the dropping cum phase separation technique. The factors affecting the sphere structure formation in relation to their efficiency as photocatalysts have been studied in detail. It was found that the increase of the nanoparticulate dopant fraction (TiO2 and/or Fe3O4) in the casting solution led to the formation of nanocomposites with a higher specific surface area as well as with enhanced photocatalytic activity. The embedment of the TiO2 nanoparticles in the polymeric matrix did not change the bandgap of the photocatalyst. Furthermore, the co-doping with Fe3O4 had no negative impact on the photocatalytic activity of the TiO2 doped porous cellulose spheres. The addition of a moderate amount of dimethylsulfoxide led to an improvement of the photocatalytic activity of the formed nanocomposites, due to an increase of the matrix porosity without an agglomeration of the active nanoparticles. However, higher fractions of dimethylsulfoxide led to the agglomeration of the photocatalytic nanoparticles and therefore a decrease of the photocatalytic activity of the hybrid materials. The obtained porous spheres could be successfully recycled and reused in at least five consecutive cycles for the photocatalytic degradation of the model organic pollutant Rhodamine B in aqueous solution. Additionally, the prepared porous spheres also exhibited good adsorber properties toward Cu2+ ions which were used in this study as model metal ion pollutant in water.
KeywordsSupported photocatalysts Cellulose nanocomposites Ionic liquids Water purification Titania nanoparticles Magnetite nanoparticles
The financial support through the Deutsche Forschungsgemeinschaft (DFG) project WI 4325/2-1 is kindly acknowledged. We gratefully acknowledge the collaboration with Mrs. Claudia Schenk (BET characterization) and Mr. Smail Boukercha (SEM characterization) at the University of Duisburg-Essen.
- Brandes R, Trindade ECA, Vanin DF, Vargas VMM, Carminatti CA, Al-Qureshi HA, Recouvreux DOS (2018) Spherical bacterial cellulose/TiO2 nanocomposite with potential application in contaminants removal from wastewater by photocatalysis. Fibers Polym 19(9):1861–1868. https://doi.org/10.1007/s12221-018-7798-7 CrossRefGoogle Scholar
- Czaja W, Krystynowicz A, Bielecki S, Brown RM Jr (2006) Microbial cellulose—the natural power to heal wounds. Biomaterials 27:145–151. https://doi.org/10.1016/j.biomaterials.2005.07.035 CrossRefGoogle Scholar
- Luo X, Lei X, Cai N, Xie X, Xue Y, Yu F (2016a) Removal of heavy metal ions from water by magnetic cellulose-based beads with embedded chemically modified magnetite nanoparticles and activated carbon. ACS Sustain Chem Eng 4:3960–3969. https://doi.org/10.1021/acssuschemeng.6b00790 CrossRefGoogle Scholar
- Maaloul N, Oulego P, Rendueles M, Ghorbal A, Diaz M (2019) Synthesis and characterization of eco-freiendly cellulose beads for cooper (II) removal from aqueous solutions. Environ Sci Pollut Res. https://doi.org/10.1007/S11356-018-3812-2
- Nevstrueva D, Pihlajamäki A, Mänttäri M (2015) Effect of a TiO2 additive on the morphology and permeability of cellulose ultrafiltration membranes prepared via immersion precipitation with ionic liquid as solvent. Cellulose 22(6):3865–3876. https://doi.org/10.1007/s10570-015-0746-4 CrossRefGoogle Scholar