Microscopic characterization of microcrack development in marble after cyclic treatment with high temperature

  • Jun Peng
  • Guan RongEmail author
  • Zhicheng Tang
  • Song Sha
Original Paper


Crack density of rocks is greatly affected by high temperature treatment and the induced thermal damage influences the strength and deformation characteristics of the rock. A good understanding of thermal cracking behavior is useful for geological evaluation of engineering structures associated with high temperature problems. This study investigates the characteristics of thermally-induced microcracks in a fine-grained dolomitic marble with different degrees of thermal damage using an optical microscope. Different degrees of thermal damage were first generated by treating the rock specimen with different heating and cooling cycles. Optical microscopy was then used to characterize the microcrack type and statistically examine the width, length, and anisotropy of thermally-induced microcracks. The results reveal that most of the generated microcracks induced by cyclic high temperature treatment are grain boundary microcracks. The width and length of microcracks significantly increases with an increasing number of heating and cooling cycles. It is also found that both grain boundary microcracks and intra-grain microcracks do not show predominant direction after thermal treatment. Finally, a quantitative relation is established to correlate the mechanical behavior of rocks (i.e., strength and modulus) with the crack density. The proposed relation is useful in understanding how the microstructure affects the properties of rocks after treatment with high temperature.


Heating and cooling cycle Thermally-induced microcrack Microscopic observation Crack density Anisotropy 



The research work presented in this paper is in part supported by the National Natural Science Foundation of China (Grant nos. 51609178, 51579189, and 41772305), the Nature Science Foundation of Hubei Province (Grant no. 2018CFB593), the China Postdoctoral Science Foundation (Grant nos. 2015M582273 and 2018T110800), and the Open-end Research Fund of the State Key Laboratory for Geomechanics and Deep Underground Engineering (Grant no. SKLGDUEK1709). The authors are grateful to these financial supporters.


  1. Altindag R, Alyildiz SI, Onargan T (2004) Mechanical property degradation of ignimbrite subjected to recurrent freeze-thaw cycles. Int J Rock Mech Min Sci 41:1023–1028CrossRefGoogle Scholar
  2. Batzle ML, Simmons G, Siegfried RW (1980) Microcrack closure in rocks under stress - direct observation. J Geophys Res 85(Nb12):7072–7090CrossRefGoogle Scholar
  3. Bauer SJ, Johnson B (1979) Effects of slow uniform heating on the physical properties of the Westerly and Charcoal granites. In: 20th US Symposium on Rock Mechanics, American Rock Mechanics Association, Austin, TexasGoogle Scholar
  4. Brotóns V, Tomás R, Ivorra S, Alarcón JC (2013) Temperature influence on the physical and mechanical properties of a porous rock: San Julian’s calcarenite. Eng Geol 167:117–127CrossRefGoogle Scholar
  5. Browning J, Meredith P, Gudmundsson A (2016) Cooling-dominated cracking in thermally stressed volcanic rocks. Geophys Res Lett 43(16):8417–8425CrossRefGoogle Scholar
  6. Chaki S, Takarli M, Agbodjan WP (2008) Influence of thermal damage on physical properties of a granite rock: porosity, permeability and ultrasonic wave evolutions. Constr Build Mater 22(7):1456–1461CrossRefGoogle Scholar
  7. Chen Y, Wang CY (1980) Thermally induced acoustic emission in westerly granite. Geophys Res Lett 7(12):1089–1092CrossRefGoogle Scholar
  8. Chen YL, Ni J, Shao W, Azzam R (2012) Experimental study on the influence of temperature on the mechanical properties of granite under uni-axial compression and fatigue loading. Int J Rock Mech Min Sci 56(8):62–66CrossRefGoogle Scholar
  9. Cheng Y, Wong LNY (2018) Microscopic characterization of tensile and shear fracturing in progressive failure in marble. J Geophys Res Solid Earth 123(1):204–225CrossRefGoogle Scholar
  10. Clark SP (1966) Handbook of physical constants. Geological Society of America, New YorkGoogle Scholar
  11. David C, Menéndez B, Darot M (1999) Influence of stress-induced and thermal cracking on physical properties and microstructure of La Peyratte granite. Int J Rock Mech Min Sci 36(4):433–448CrossRefGoogle Scholar
  12. Fredrich JT, Wong T (1986) Micromechanics of thermally induced cracking in three crustal rocks. J Geophys Res Solid Earth 91(B12):12743–12764CrossRefGoogle Scholar
  13. Freire-Lista DM, Fort R, Varas-Muriel MJ (2016) Thermal stress-induced microcracking in building granite. Eng Geol 206:83–93CrossRefGoogle Scholar
  14. Geraud Y, Mazerolle F, Raynaud S, Lebon P (1998) Crack location in granitic samples submitted to heating, low confining pressure and axial loading. Geophys J Int 133:553–567CrossRefGoogle Scholar
  15. Gónzalez-Gómez WS, Quintana P, May-Pat A, Avilés F, May-Crespo J, Alvarado-Gil JJ (2015) Thermal effects on the physical properties of limestones from the Yucatan peninsula. Int J Rock Mech Min Sci 75:182–189CrossRefGoogle Scholar
  16. Griffiths L, Lengliné O, Heap MJ, Baud P, Schmittbuhl J (2018) Thermal cracking in westerly granite monitored using direct wave velocity, coda wave interferometry, and acoustic emissions. J Geophys Res Solid Earth 123(3):2246–2261CrossRefGoogle Scholar
  17. Heuze FE (1983) High-temperature mechanical, physical and thermal properties of granitic rocks - a review. Int J Rock Mech Min Sci Geomech Abstr 20(1):3–10CrossRefGoogle Scholar
  18. Homand F, Hoxha D, Belem T, Pons MN, Hoteit N (2000) Geometric analysis of damaged microcracking in granites. Mech Mater 32(6):361–376CrossRefGoogle Scholar
  19. Homand-Etienne F, Houpert R (1989) Thermally induced microcracking in granites: characterization and analysis. Int J Rock Mech Min Sci Geomech Abstr 26(2):125–134CrossRefGoogle Scholar
  20. Johnson B, Gangi AF, Handin J (1978) Thermal cracking of rock subjected to slow uniform temperature changes. In: 19th US Symposium on Rock Mechanics, American Rock Mechanics Association, Reno, NevadaGoogle Scholar
  21. Jones C, Keaney G, Meredith PG, Murrell SAF (1997) Acoustic emission and fluid permeability measurements on thermally cracked rocks. Phys Chem Earth 22(1):13–17CrossRefGoogle Scholar
  22. Keshavarz M, Pellet FL, Loret B (2010) Damage and changes in mechanical properties of a gabbro thermally loaded up to 1,000 C. Pure Appl Geophys 167(12):1511–1523CrossRefGoogle Scholar
  23. Kranz RL (1983) Microcracks in rocks: a review. Tectonophysics 100(1):449–480CrossRefGoogle Scholar
  24. Li Z, Wong LNY, Teh CI (2017) Low cost colorimetry for assessment of fire damage in rock. Eng Geol 228:50–60CrossRefGoogle Scholar
  25. Lim SS, Martin CD, Åkesson U (2012) In-situ stress and microcracking in granite cores with depth. Eng Geol 147:1–13CrossRefGoogle Scholar
  26. Liu S, Xu J (2014) Mechanical properties of Qinling biotite granite after high temperature treatment. Int J Rock Mech Min Sci 71:188–193CrossRefGoogle Scholar
  27. Mahanta B, Singh TN, Ranjith PG (2016) Influence of thermal treatment on mode I fracture toughness of certain Indian rocks. Eng Geol 210:103–114CrossRefGoogle Scholar
  28. Mahmutoglu Y (1998) Mechanical behaviour of cyclically heated fine grained rock. Rock Mech Rock Eng 31:169–179CrossRefGoogle Scholar
  29. Mahmutoğlu Y (2006) The effects of strain rate and saturation on a micro-cracked marble. Eng Geol 82(3):137–144CrossRefGoogle Scholar
  30. Mahmutoğlu Y (2017) Prediction of weathering by thermal degradation of a coarse-grained marble using ultrasonic pulse velocity. Environ Earth Sci 76(12):435CrossRefGoogle Scholar
  31. Menéndez B, David C, Darot M (1999) A study of the crack network in thermally and mechanically cracked granite samples using confocal scanning laser microscopy. Phys Chem Earth 24(7):627–632CrossRefGoogle Scholar
  32. Meredith PG, Knight KS, Boon SA, Wood IG (2001) The microscopic origin of thermal cracking in rocks: an investigation by simultaneous time-of-flight neutron diffraction and acoustic emission monitoring. Geophys Res Lett 28(10):2105–2108CrossRefGoogle Scholar
  33. Moore DE, Lockner DA (1995) The role of microcracking in shear-fracture propagation in granite. J Struct Geol 17(1):95–114CrossRefGoogle Scholar
  34. Mutlutürk M, Altındağ R, Türk G (2004) A decay function model for the integrity loss of rock when subjected to recurrent cycles of freezing-thawing and heating-cooling. Int J Rock Mech Min Sci 41:237–244CrossRefGoogle Scholar
  35. Nasseri MHB, Schubnel A, Young R (2007) Coupled evolutions of fracture toughness and elastic wave velocities at high crack density in thermally treated westerly granite. Int J Rock Mech Min Sci 44(4):601–616CrossRefGoogle Scholar
  36. Peng J, Rong G, Cai M, Yao MD, Zhou CB (2016a) Physical and mechanical behaviors of a thermal-damaged coarse marble under uniaxial compression. Eng Geol 200:88–93CrossRefGoogle Scholar
  37. Peng J, Rong G, Cai M, Yao MD, Zhou CB (2016b) Comparison of mechanical properties of undamaged and thermal-damaged coarse marbles under triaxial compression. Int J Rock Mech Min Sci 83:135–139CrossRefGoogle Scholar
  38. Ranjith PG, Viete DR, Chen BJ, Perera MSA (2012) Transformation plasticity and the effect of temperature on the mechanical behaviour of Hawkesbury sandstone at atmospheric pressure. Eng Geol 151:120–127CrossRefGoogle Scholar
  39. Rong G, Peng J, Yao M, Jiang Q, Wong LNY (2018a) Effects of specimen size and thermal-damage on physical and mechanical behavior of a fine-grained marble. Eng Geol 232:46–55CrossRefGoogle Scholar
  40. Rong G, Yao M, Peng J, Sha S, Tan J (2018b) Influence of initial thermal cracking on physical and mechanical behaviour of a coarse marble: insights from uniaxial compression tests with acoustic emission monitoring. Geophys J Int 214:1886–1900Google Scholar
  41. Rong G, Peng J, Cai M, Yao M, Zhou C, Sha S (2018c) Experimental investigation of thermal cycling effect on physical and mechanical properties of bedrocks in geothermal fields. Appl Therm Eng 141:174–185CrossRefGoogle Scholar
  42. Rosengren KJ, Jaeger JC (1968) The mechanical properties of a low porosity interlocked aggregate. Geotechnique 18:317–326CrossRefGoogle Scholar
  43. Roy DG, Singh TN (2016) Effect of heat treatment and layer orientation on the tensile strength of a crystalline rock under Brazilian test condition. Rock Mech Rock Eng 49(5):1663–1677CrossRefGoogle Scholar
  44. Simmons G, Cooper HW (1978) Thermal cycling cracks in three igneous rocks. Int J Rock Mech Min Sci Geomech Abstr 15(4):145–148CrossRefGoogle Scholar
  45. Sirdesai NN, Singh TN, Gamage RP (2017) Thermal alterations in the poro-mechanical characteristic of an Indian sandstone–a comparative study. Eng Geol 226:208–220CrossRefGoogle Scholar
  46. Sirdesai NN, Singh A, Sharma LK, Singh R, Singh TN (2018) Determination of thermal damage in rock specimen using intelligent techniques. Eng Geol 239:179–194CrossRefGoogle Scholar
  47. Sprunt ES, Brace WF (1974) Direct observation of microcavities in crystalline rocks. Int J Rock Mech Min Sci 11(4):139–150CrossRefGoogle Scholar
  48. Tapponnier P, Brace WF (1976) Development of stress-induced microcracks in westerly granite. Int J Rock Mech Min Sci Geomech Abstr 13(4):103–112CrossRefGoogle Scholar
  49. Tian H, Kempka T, Xu NX, Ziegler M (2012) Physical properties of sandstones after high temperature treatment. Rock Mech Rock Eng 45:1113–1117CrossRefGoogle Scholar
  50. Tian H, Ziegler M, Kempka T (2014) Physical and mechanical behavior of claystone exposed to temperatures up to 1000°C. Int J Rock Mech Min Sci 70:144–153CrossRefGoogle Scholar
  51. Tian H, Kempka T, Xu S, Ziegler M (2016) Mechanical properties of sandstones exposed to high temperature. Rock Mech Rock Eng 49:321–327CrossRefGoogle Scholar
  52. Ulusay R, Hudson JA (2007) The complete ISRM suggested methods for rock characterization, testing and monitoring: 1974–2006. ISRM commission on testing methods, AnkataGoogle Scholar
  53. Wang HF, Heard HC (1985) Prediction of elastic moduli via crack density in pressurized and thermally stressed rock. J Geophys Res 90(B12):10342–10350CrossRefGoogle Scholar
  54. Wang HF, Bonner BP, Carlson SR, Kowallis B, Heard HC (1989) Thermal stress cracking in granite. J Geophys Res Solid Earth 94(B2):1745–1758CrossRefGoogle Scholar
  55. Wong TF (1982) Micromechanics of faulting in westerly granite. Int J Rock Mech Min Sci Geomech Abstr 19(2):49–64CrossRefGoogle Scholar
  56. Wong LNY, Li Z, Kang HM, Teh CI (2017) Dynamic loading of Carrara marble in a heated state. Rock Mech Rock Eng.
  57. Yang SQ, Hu B (2018) Creep and long-term permeability of a red sandstone subjected to cyclic loading after thermal treatments. Rock Mech Rock Eng.
  58. Yang SQ, Ranjith PG, Jing HW, Tian WL, Ju Y (2017) An experimental investigation on thermal damage and failure mechanical behavior of granite after exposure to different high temperature treatments. Geothermics 65:180–197CrossRefGoogle Scholar
  59. Yao M, Rong G, Zhou C, Peng J (2016) Effects of thermal damage and confining pressure on the mechanical properties of coarse marble. Rock Mech Rock Eng 49(6):2043–2054CrossRefGoogle Scholar
  60. Yavuz H, Altindag R, Sarac S, Ugur I, Sengun N (2006) Estimating the index properties of deteriorated carbonate rocks due to freeze-thaw and thermal shock weathering. Int J Rock Mech Min Sci 43(5):767–775CrossRefGoogle Scholar
  61. Yavuz H, Demirdag S, Caran S (2010) Thermal effect on the physical properties of carbonate rocks. Int J Rock Mech Min Sci 47(1):94–103CrossRefGoogle Scholar
  62. Zhu Z, Tian H, Jiang G, Cheng W (2018) Effects of high temperature on the mechanical properties of Chinese marble. Rock Mech Rock Eng.
  63. Zuo JP, Xie HP, Zhou HW, Peng SP (2010) SEM in situ investigation on thermal cracking behaviour of Pingdingshan sandstone at elevated temperatures. Geophys J Int 181(2):593–603Google Scholar

Copyright information

© Springer-Verlag GmbH Germany, part of Springer Nature 2019

Authors and Affiliations

  1. 1.State Key Laboratory of Water Resources and Hydropower Engineering ScienceWuhan UniversityWuhanChina
  2. 2.School of Civil EngineeringWuhan UniversityWuhanChina
  3. 3.Faculty of EngineeringChina University of GeosciencesWuhanChina

Personalised recommendations