Advertisement

Generalised Analytical Models for the Strength of the Inclined as well as the Flat Coal Pillars using Rock Mass Failure Criterion

  • Arka Jyoti Das
  • Prabhat Kumar MandalEmail author
  • Partha Sarathi Paul
  • Rabindra Kumar Sinha
Original Paper

Abstract

The assessment of the strength of the coal pillars is essential for the safe extraction of the coal seam. All the pillar strength formulae used worldwide are developed for the flat coal pillars. Therefore, their adoption in evaluating the strength of the inclined coal pillars may endanger the workings of the inclined coal seams. The strength of an inclined coal pillar should be estimated by considering the inclination of the coal seam and its associated behaviour, because the shearing effect along the true dip aggravates the instability of the inclined coal pillars. In this paper, generalised analytical solutions have been developed to estimate the strength of the coal pillars which can be applied for both the inclined and flat coal pillars. The mathematical models are derived to obtain the confining stress in the coal pillar and the corresponding peak stress at the time of its failure using a rock mass failure criterion. The mathematical expressions are also developed for the stress distribution over the pillar considering the increase of the shearing effect with the dip of the coal seam. The Mohr–Coulomb criterion is considered for the shear characteristics at the interfaces of pillar–floor and pillar–roof. The asymmetrical stress distribution and failure along the dip-rise and the strike directions of the inclined coal pillars are addressed in this study. The concept of the confined core and three-dimensional stress distribution over the coal pillar are used to derive the strength formulae for the square, rectangular, and very long pillars. The performance of the derived strength formulae is assessed by the stable and failed cases of the flat and the inclined coal pillars. It is observed that all the inclined and flat coal pillars cases are correctly predicted by the derived generalised strength formulae. According to the derived strength formulae, the strength of the inclined coal pillar decreases with the increase of the inclination of the coal pillar. This paper also describes the variation of the strength of the inclined coal pillars with respect to the coal seam inclinations and the frictional properties of the contact planes for the different width-to-height ratios.

Keywords

Yield zone Rock mass failure criterion Inclined coal pillar strength Flat coal pillar strength 

List of Symbols

\({\sigma _{1{\text{sm}}}}\;{\text{and}}\;{\sigma _{1{\text{bm}}}}\)

Strength of the solid coal mass and broken coal under confinement

\({\sigma _{3{\text{sm}}}}\;{\text{and}}\;{\sigma _{3{\text{bm}}}}\)

Confining stress of the solid coal mass and broken coal

\({\sigma _{{\text{cbm}}}}\)

Uniaxial compressive strength (UCS) of the broken coal

\(a\;{\text{and}}\;b\)

Constants

\({f_{{\text{sm}}}}({\sigma _3})\;{\text{and}}\;{f_{{\text{bm}}}}({\sigma _3})\)

Failure envelops of the solid coal mass and the broken coal

\({\sigma _{1{\text{T}}}}\)

Maximum peak stress in the pillar

\({\sigma _{3{\text{T}}}}\)

Confining stress in the pillar corresponding to \({\sigma _{{\text{1T}}}}\)

\({\varphi _{{\text{bm}}}}\)

Internal friction angle of the broken coal

\(\sigma\)

Vertical stress during loading

\(X,{\text{ }}Y{\text{ and }}Z{\text{ axes}}\)

Directions along the dip-rise, the strike, and the normal to the coal seam

\({\sigma _z}\;{\text{and}}\;{\sigma _s}\)

Normal and shear components of the vertical stress

\(\alpha\)

Inclination of the coal seam

\(h\)

Height of the pillar

\(\gamma\)

Bulk weight of coal

\(k\)

In-situ major horizontal and vertical stress ratio

\({\sigma _{\text{r}}}\)

Resultant stress on the inclined pillar

\({\sigma _x}\;{\text{and}}\;{\sigma _y}\)

Confinement of the pillar along the dip-rise and the strike direction

\(\tau\)

Shear stress acting on the contact plane between the pillar/floor and pillar/roof

\(\mu\)

Coefficient of friction of the contact surface between the pillar/floor and pillar/roof

\({L_{\text{D}}}\)

Distance from the edge of the inclined coal pillar along the dip-rise direction when \({\sigma _x}={\sigma _{{\text{3T}}}}\) and \({\sigma _z}={\sigma _{{\text{1T}}}}\)

\({L_{\text{S}}}\)

Distance from the edge of the coal pillar along the strike direction when \({\sigma _y}={\sigma _{{\text{3T}}}}\) and \({\sigma _z}={\sigma _{{\text{1T}}}}\).

\(s\)

Strength of the pillar

\({A_{\text{p}}}\)

Plan area of the pillar

\({A_z}\)

Plan area of the small strip of height dσz.

\(w\)

Width of square pillar

\({w_1}\;{\text{and}}\;{w_2}\)

Shorter side and longer side of rectangle

\({\text{L}}{{\text{i}}_2}\)

Dilogarithm

\({\sigma _{{\text{cm}}}}\)

UCS of the cubical pillar

\({\sigma _{\text{c}}}\)

UCS of the coal obtained from laboratory

\(H\)

Depth of cover

\(B\)

Width of the gallery

Notes

Acknowledgements

The authors are obliged to the Directors, CSIR-Central Institute of Mining and Fuel Research, Dhanbad and Indian Institute of Technology (ISM), Dhanbad for their kind encouragement and support to publish this paper. The views expressed in this paper are that of the authors and not necessarily of the organisations to which they belong.

References

  1. Amadei B, Pan E (1992) Gravitational stresses in anisotropic rock masses with inclined strata. Int J Rock Mech Min Sci Geomech Abst 29:225–236CrossRefGoogle Scholar
  2. Amadei B, Savage WZ (1989) Anisotropic nature of jointed rock mass strength. J Eng Mech 115:525–542CrossRefGoogle Scholar
  3. Ashby MF, Sammis CG (1990) The damage mechanics of brittle solids in compression. Pure Appl Geophys 133:489–521CrossRefGoogle Scholar
  4. Barron K (1986) A new method for coal pillar design. In: Proceedings of ground movement and control related to coal mining, AusIMM Melbourne, pp 118–124Google Scholar
  5. Bertuzzi R, Douglas K, Mostyn G (2016) An approach to model the strength of coal pillars. Int J Rock Mech Min Sci 89:165–175CrossRefGoogle Scholar
  6. Bieniawski ZT (1968) The effect of specimen size on compressive strength of coal. Int J Rock Mech Min Sci Geomech Abst 5:325–335CrossRefGoogle Scholar
  7. Bobet A, Einstein HH (1998) Fracture coalescence in rock-type materials under uniaxial and biaxial compression. Int J Rock Mech Min Sci 35:863–888CrossRefGoogle Scholar
  8. Byerlee JD (1967) Frictional characteristics of granite under high confining pressure. J Geophys Res 72:3639–3648CrossRefGoogle Scholar
  9. Das MN (1986) Influence of width/height ratio on post-failure behaviour of coal. Int J Min Geol Eng 4:79–87CrossRefGoogle Scholar
  10. Das AJ, Mandal PK, Bhattacherjee R, Tiwari S, Kushwaha A, Roy LB (2017a) Evaluation of stability of underground workings for exploitation of an inclined coal seam by the ubiquitous joint model. Int J Rock Mech Min Sci 93:101–114CrossRefGoogle Scholar
  11. Das AJ, Mandal PK, Paul PS, Sinha RK, Kushwaha A, Tewari S (2017b) Effect of the strata inclination during underground extraction of the inclined coal seams. In: Proceedings of the 7th Asian Mining Congress, Kolkata 156–160Google Scholar
  12. Foroughi MH (1996) Some aspects of coal pillar stability in inclined coal seams. PhD thesis, University of New South Wales, pp 1–273Google Scholar
  13. Gaddy FL (1956) A study of the ultimate strength of coal as related to the absolute size of cubical specimens tested. Virginia Polytech Bull, pp1–27Google Scholar
  14. Gale WJ, Blackwood RL (1987) Stress distributions and rock failure around coal mine roadways. Int J Rock Mech Min Sci Geomech Abst 24:165–173CrossRefGoogle Scholar
  15. Gao F, Kang H (2017) Experimental study on the residual strength of coal under low confinement. Rock Mech Rock Eng 50:285–296CrossRefGoogle Scholar
  16. Greenwald HP, Howarth HC, Hartmann I (1941) Experiments on strength of small pillars of coal in the pittsburgh bed. US Bureau of Mines, p 605Google Scholar
  17. Hardy P, Agapito JF (1982) Induced horizontal stress method of pillar design in oil shale. In: 15th Oil shale symp. Colorado School of Mines, Golden, ColoradoGoogle Scholar
  18. He MC, Nie W, Zhao ZY, Guo W (2012) Experimental investigation of bedding plane orientation on the rockburst behavior of sandstone. Rock Mech Rock Eng 45:311–326CrossRefGoogle Scholar
  19. Hertz H (1881) On the contact of elastic solids. J fur de reine Angewandte Mathematik 92:156–171Google Scholar
  20. Hobbs DW (1970) The behavior oof broken rock under triaxial compression. Int J Rock Mech Min Sci Geomech Abst 7:125–148CrossRefGoogle Scholar
  21. Hoek E, Bieniawski ZT (1965) Brittle fracture propagation in rock under compression. Int J Frac Mech 1:137–155Google Scholar
  22. Hoek E, Brown ET (1980) Empirical strength criterion for rock masses. J Geotech Geoenviron Eng ASCE 106:1013–1035Google Scholar
  23. Hoek E, Carranza TC, Corkum B (2002) Hoek-Brown failure criterion-2002 edition. In: RocLab ManualGoogle Scholar
  24. Holland CT (1962) Design of pillars for overburden support - Part 1. Min Congr J 48:24–28 (and Part 2 48:66–71)Google Scholar
  25. Holland CT (1964) The strength of coal pillars. In: Proceedings of the 6th US symposium on rock mechanics, University of Missouri, Rolla, pp 450–466Google Scholar
  26. Horii H, Nemat-Nasser S (1985) Compression-induced microcrack growth in brittle solids: axial splitting and shear failure. J Geophys Res: Solid Earth 90:3105–3125CrossRefGoogle Scholar
  27. Horii H, Nemat-Nasser S (1986) Brittle failure in compression: splitting faulting and brittle-ductile transition. Philos Trans R Soc Lond A 319:337–374CrossRefGoogle Scholar
  28. Hustrulid WA (1976) A review of coal pillar strength formulas. Rock Mech Rock Eng 8:115–145CrossRefGoogle Scholar
  29. Iannacchione AT (1990) The effects of roof and floor interface slip on coal pillar behavior. In: Proceedings of the 31st US Symposium on Rock Mechanics, pp 156–160Google Scholar
  30. Jaiswal A, Shrivastva BK (2009) Numerical simulation of coal pillar strength. Int J Rock Mech Min Sci 46:779–788CrossRefGoogle Scholar
  31. Jawed M, Sinha RK, Sengupta S (2013) Chronological development in coal pillar design for bord and pillar workings: a critical appraisal. J Geol Min Res 5:1–11CrossRefGoogle Scholar
  32. Kang HP, Zhang X, Si LP, Wu Y, Gao F (2010) In-situ stress measurements and stress distribution characteristics in underground coal mines in China. Eng Geol 116:333–345CrossRefGoogle Scholar
  33. Lin Y, Hong YZ, Zheng SG, Zhang Y (1984) Failure modes of openings in a steeply bedded rock mass. Rock Mech Rock Eng 17:113–119CrossRefGoogle Scholar
  34. Logie CV, Matheson GM (1982) A critical review of the current state-of-the-art design of mine pillars. In: Brawner CO (ed) Proceedings of the first international conference of stability of underground mining. Vancouver, AIME, New York, pp 359–382Google Scholar
  35. Loui JP, Jhanwar JC, Sheorey PR (2007) Assessment of roadway support adequacy in some Indian manganese mines using theoretical in-situ stress estimates. Int J Rock Mech Min Sci 44:148–155CrossRefGoogle Scholar
  36. Mandal PK, Singh R, Maiti J, Singh AK, Kumar R, Sinha A (2008) Underpinning-based simultaneous extraction of contiguous sections of a thick coal seam under weak and laminated parting. Int J Rock Mech Min Sci 45:11–28CrossRefGoogle Scholar
  37. Mathey M (2015) Investigation into the mechanism of strength and failure in squat coal pillars in South Africa. Ph.D. Thesis, University of the Witwatersrand, Johannesburg, South Africa, p 202Google Scholar
  38. Mathey M, Van der Merwe JN (2016) Critique of the South African squat coal pillar strength formula. J S Afr I Min Metall 116:291–299Google Scholar
  39. Maurer WC (1965) Shear failure of rock under compression. Soc Petrol Eng J 5:167–176CrossRefGoogle Scholar
  40. Mogi K (1966) Pressure dependence of rock strength and transition from brittle to ductile flow. Bull Earthq Res Inst Univ Tokyo 44:215–232Google Scholar
  41. Mogi K (1971) Fracture and flow of rocks under high triaxial compression. J Geophys Res 76:1255–1269CrossRefGoogle Scholar
  42. Mohan GM, Sheorey PR, Kushwaha A (2001) Numerical estimation of pillar strength in coal mines. Int J Rock Mech Min Sci 38:1185–1192CrossRefGoogle Scholar
  43. Obert L, Duvall WI (1967) Rock Mechanics and the Design of Structures in Rock. John Wiley & Sons Inc, New York, pp 542–545Google Scholar
  44. Pariseau WG (1982) Shear stability of mine pillars in dipping seams. In: Proc. of the 23rd US symposium on rock mechanics (USRMS), American Rock Mechanics Association, 25–27 August, Berkeley, CaliforniaGoogle Scholar
  45. Ramamurthy T (1995) Bearing capacity of rock foundation. Balkem, RotterdamGoogle Scholar
  46. Ran JQ, Passaris EKS, Mottahed P (1994) Shear sliding failure of the jointed roof in laminated rock mass. Rock Mech Rock Eng 27:235–251CrossRefGoogle Scholar
  47. Rastiello G, Federico F, Screpanti S (2015) New soft rock pillar strength formula derived through parametric FEA using a critical state plasticity model. Rock Mech Rock Eng 48:2077–2091CrossRefGoogle Scholar
  48. Salamon MDG, Munro AH (1967) A study of the strength of coal pillars. J S Afr Inst Min Metall 68:55–67Google Scholar
  49. Salamon MDG, Wagner H (1985) Practical experiences in the design of coal pillars. In: Proceedings of the 21st international conference of safety in mines research institutes, Sydney, Australia, pp 3–9Google Scholar
  50. Sheorey PR (1992) Pillar strength considering in-situ stress. In: Proceedings of the workshop on coal pillar mechanics and design, Santa Fe, Ed. A.T. USBM IC 9315, 122–127Google Scholar
  51. Sheorey PR (1997) Empirical Rock Failure criteria. Balkema, RotterdamGoogle Scholar
  52. Sheorey PR, Das MN, Singh B (1982) A numerical procedure for rock pressure problems in level seams. In: Proceedings of the symposium on strata mechanics, Newcastle upon Tyne (edited by I.W. Farmer), Elsevier, Amsterdam, pp 254–259Google Scholar
  53. Sheorey PR, Das MN, Bordia SK, Singh B (1986) Pillar strength approaches based on a new failure criterion for coal seams. Int J Min Geol Eng 4:273–290CrossRefGoogle Scholar
  54. Sheorey PR, Das MN, Barat D, Parasad RK, Singh B (1987) Coal pillar strength estimation from failed and stable cases. Int J Rock Mech Min Sci 24:347–355CrossRefGoogle Scholar
  55. Sheorey PR, Biswas AK, Choubey VD (1989) An empirical failure criterion for rocks and jointed rock masses. Eng Geol 26:141–159CrossRefGoogle Scholar
  56. Singh R, Sheorey PR, Singh DP (2002) Stability of parting between coal pillar workings in level contiguous seams. Int J Rock Mech Min Sci 39:9–39CrossRefGoogle Scholar
  57. Singh R, Mandal PK, Singh AK, Kumar R, Mait J, Ghosh AK (2008) Upshot of strata movement during underground mining of a thick coal seam below hilly terrain. Int J Rock Mech Min Sci 45:29–46CrossRefGoogle Scholar
  58. Singh AK, Singh R, Maiti J, Kumar R, Mandal PK (2011) Assessment of mining induced stress development over coal pillars during depillaring. Int J Rock Mech Min Sci 48:805–818CrossRefGoogle Scholar
  59. Steart FA (1954) Strength and stability of pillars in coal mines. J Chem Metall Min Soc S Afr 54:309–325Google Scholar
  60. Tang CA, Kou SQ (1998) Crack propagation and coalescence in brittle materials under compression. Eng Fract Mech 61:311–324CrossRefGoogle Scholar
  61. Tewari S, Kushwaha A, Bhattacharjee R, Porathur JL (2018) Crown pillar design in highly dipping coal seam. Int J Rock Mech Min Sci 31:12–19CrossRefGoogle Scholar
  62. Ünlü T (2001) Critical dimension concept in pillar stability. In: Proceedings of the 17th international mining congress and exhibition of Turkey, pp 341–347Google Scholar
  63. Van der Merwe JN (1999) New strength formula for coal pillars in South Africa. In: Mark C, Heasley KA, Iannacchione AT, Tuchman RJ (Eds) Proceedings of the second international workshop on coal pillar mechanics and design, Pittsburgh, US, pp 99–114Google Scholar
  64. Van der Merwe JN (2003a) New pillar strength formula for South African coal. J S Afr Inst Min Metall 3:281–292Google Scholar
  65. Van der Merwe JN (2003b) New pillar strength formula for South African coal. J S Afr Inst Min Metal 103:281–292Google Scholar
  66. Vardar O, Tahmasebinia F, Zhang C, Canbulat I, Saydam S (2017) A review of uncontrolled pillar failures. Proc Eng 191:631–637CrossRefGoogle Scholar
  67. Watson JM, Vakili A, Jakubowski M (2015) Rock strength anisotropy in high stress conditions: a case study for application to shaft stability assessments. Stud Geotech et Mecha 37:115–125CrossRefGoogle Scholar
  68. Wei G (2014) Study on the width of the non-elastic zone in inclined coal pillar for strip mining. Int J Rock Mech Min Sci 72:304–310CrossRefGoogle Scholar
  69. Wilson AH (1972) A hypothesis concerning pillar stability. Min Engr 131:409–417Google Scholar
  70. Wilson AH (1982) Pillar stability in longwall mining. In: Chugh YP, Karmis M (eds) Proceedings of the state-of-the-art of ground control in longwall mining and mining subsidence. SME, New York, pp 85–95Google Scholar
  71. Wilson AH (1983) The stability of underground workings in the soft rocks of the coal measures. Int J Min Eng 1:91–187CrossRefGoogle Scholar
  72. Wong RH, Lin P, Tang CA (2006) Experimental and numerical study on splitting failure of brittle solids containing single pore under uniaxial compression. Mech Mater 38:142–159CrossRefGoogle Scholar
  73. Xin Y, Gou P, Ge F (2014) Analysis of stability of support and surrounding rock in mining top coal of inclined coal seam. Int J Rock Mech Min Sci 24:63–68CrossRefGoogle Scholar
  74. Yavuz H (2004) An estimation method for cover pressure re-establishment distance and pressure distribution in the goaf of longwall coal mines. Int J Rock Mech Min Sci 41:193–205CrossRefGoogle Scholar
  75. Yudhbir LW, Prinzl F (1983) An empirical failure criterion for rock masses. In: Proceedings of the 5th international congress on rock mechanics, Melbourne, Balkema, Rotterdam, pp 1–8Google Scholar
  76. Zhao LY, Zhu QZ, Shao JF (2018) A micro-mechanics based plastic damage model for quasi-brittle materials under a large range of compressive stress. Int J Plas 100:156–176CrossRefGoogle Scholar
  77. Zipf RK Jr, Mark C (1997) Design methods to control violent pillar failures in room-and-pillar mines. T I Min Metall A-Min Ind 106:A124–A132Google Scholar

Copyright information

© Springer-Verlag GmbH Austria, part of Springer Nature 2019

Authors and Affiliations

  1. 1.CSIR-Central Institute of Mining and Fuel ResearchDhanbadIndia
  2. 2.Indian Institute of Technology (Indian School of Mines)DhanbadIndia

Personalised recommendations