The evolution of the temperature field during cavity collapse in liquid nitromethane. Part I: inert case
- 313 Downloads
- 1 Citations
Abstract
This work is concerned with the effect of cavity collapse in non-ideal explosives as a means of controlling their sensitivity. The main objective is to understand the origin of localised temperature peaks (hot spots) which play a leading order role at the early stages of ignition. To this end, we perform two- and three-dimensional numerical simulations of shock-induced single gas-cavity collapse in liquid nitromethane. Ignition is the result of a complex interplay between fluid dynamics and exothermic chemical reaction. In order to understand the relative contribution between these two processes, we consider in this first part of the work the evolution of the physical system in the absence of chemical reactions. We employ a multi-phase mathematical formulation which can account for the large density difference across the gas–liquid material interface without generating spurious temperature peaks. The mathematical and physical models are validated against experimental, analytic, and numerical data. Previous inert studies have identified the impact of the upwind (relative to the direction of the incident shock wave) side of the cavity wall to the downwind one as the main reason for the generation of a hot spot outside of the cavity, something which is also observed in this work. However, it is also apparent that the topology of the temperature field is more complex than previously thought and additional hot spot locations exist, which arise from the generation of Mach stems rather than jet impact. To explain the generation mechanisms and topology of the hot spots, we carefully follow the complex wave patterns generated in the collapse process and identify specifically the temperature elevation or reduction generated by each wave. This enables tracking each hot spot back to its origins. It is shown that the highest hot spot temperatures can be more than twice the post-incident shock temperature of the neat material and can thus lead to ignition. By comparing two-dimensional and three-dimensional simulation results in the context of the maximum temperature observed in the domain, it is apparent that three-dimensional calculations are necessary in order to avoid belated ignition times in reactive scenarios.
Keywords
Condensed phase explosives Cavity collapse Temperature Nitromethane Hot spots1 Introduction
Many explosives used in mining are insensitive and do not detonate under typical shock loading conditions, to ensure their safe transportation to mining sites. Before being detonated in blastholes, these explosives have to be sensitised by including artificial impurities such as gas cavities or glass micro-balloons.
The mechanism by which the sensitivity of the explosives is increased is a combination of hydrodynamic, thermodynamic, and chemical effects when these cavities collapse under the influence of an incident shock wave. Upon collapse, regions of locally high pressure and high temperature are generated, which are often referred to as hot spots. If these regions are large enough and maintain high temperatures for a sufficient amount of time, they can lead to the local ignition of the material and subsequently thermal runaway. In such cases, the time to ignition is observed to be considerably shorter than the time needed for the ignition of the neat explosive; thus, the cavities are considered to sensitise the material.
To this end, experimental and numerical studies have been performed, aiming to better understand the physical processes behind the shock-induced cavity collapse and the sensitisation mechanism, which are imperative to the optimisation of the performance of non-ideal, inhomogeneous explosives. Studying inhomogeneous explosives at the macro-scale, for example in the form of a rate stick simulation or experiment, provides insight into the overall effect the inhomogeneities have on the behaviour of the bulk of the explosive. However, the length-scales and time-scales governing the collapse of the cavities and the initiation and transition to detonation of the explosive bulk are massively disparate. As a result, it is very difficult for a macro-scale simulation or an experiment to simultaneously and adequately capture both processes.
Hence, considerable focus has turned to understanding the meso-scale physics by means of resolved simulations or experiments of cavity collapse to thereafter upscale to the bulk. To reduce the complexity of the process induced by the chemical reactions, several researchers concentrated on the shock-induced cavity collapse phenomenon in isolation, as a purely hydrodynamical process, emphasising on the mechanical and the induced thermodynamic effects.
For example, extensive experimental studies have been performed to identify the process governing the cavity collapse and determine the mechanical effects behind hot spot generation. A series of experiments of air cavities (diameter 5–8 mm) collapsing under the influence of shocks of various strengths (0.3–5 GPa) in gelatinous materials have been undertaken by Field and co-workers [1, 2]. Bourne and Field [1] studied the collapse process of isolated cavities of various shapes (circular, triangular, semi-circular, elliptical) in an inert medium. Dear and Field [2] considered multi-cavity systems collapsing in an inert material and observed phenomena such as jet deviation, asymmetric collapse and double jetting in columns of cavities and shielding effects and pressure amplification in rows of cavities. More recently, Swantek and Austin [3, 4] studied collapsing cavity arrays under stress loading and analysed the velocity fields around them.
Similar studies were performed by numerical means, looking at the shock–cavity interaction process in various configurations. Many numerical studies include collapse in gaseous media or focus on pressure fields alone. Here, we discuss selectively only a small number of papers that involve non-gaseous media and concentrate on the ones demonstrating results on temperature fields, as these are directly relevant to this work. Mader [5] was one of the first to simulate the collapse of a cavity in nitromethane and calculate the nitromethane temperature field around the cavity, to compare against the post-shock, neat material temperature. However, this work was limited by resolution, as the computers at the time were not yet capable of handling the heavy computation needed for adequately resolving such processes. Bourne and Milne [6, 7] modelled the temperature within the collapsing cavity, for circular, triangular and hemispherical isolated cavities and cavities in arrays. Ball et al. [8] and Hawker and Ventikos [9] simulated a single cavity collapse in water and computed the water temperature field, while Lauer et al. [10], Michael et al. [11], and Betney et al. [12] simulated the collapse of arrays in water and focused on the effect of the collapse on the pressure field and subsequent pressure amplification. Similarly, the collapse of circular and ellipsoidal cavities collapsing in an inert, hydrodynamically modelled solid material was studied by Ozlem et al. [13] who also focused on the pressure fields recovery and Kapila et al. [14] who presented temperature fields in an exemplary explosive. Limited results on the shock–cavity collapse in nitromethane were presented by Michael and Nikiforakis [15], in HNS by Kittel and Yarrington [16], and in HMX by Menikoff [17]. In an elastoplastic framework, Tran and Udaykumar [18, 19] and Kapahi and Udaykumar [20] studied the response of inert and reactive HMX with micron-sized cavities, while Rai et al. [21, 22] considered the resolution required for simulations of reactive cavity collapse and the sensitivity behaviour of elongated cavities in HMX.
The studies mentioned above have contributed to our understanding of the cavity-collapse mechanisms. However, there are still challenges in performing a complete, physical simulation of the initiation of a condensed phase explosive by shock-induced cavity collapse. An important step forward would be to address and rectify the current simulation challenges and work towards a complete simulation of the phenomenon. Such challenges include the non-trivial use of complex equations of state for describing the materials involved in the simulation, retaining at least 1000:1 density difference across the cavity boundary, maintaining oscillation-free interfaces (in terms of pressures, velocities, and temperatures), obtaining realistic temperature fields in the explosive matrix and heavy computations required for well-resolved, three-dimensional simulations.
A major challenge worthy of special attention is the accurate and oscillation-free recovery of temperature fields in the explosive matrix. This is of critical importance as the ignition process of the energetic material is a temperature-driven effect; thus, the accurate prediction of ignition relies on physically meaningful temperatures. An essential prerequisite for recovering accurate temperature fields is the characterisation of the explosive material by means of a realistic equation of state, for example in Mie–Grüneisen rather than in polytropic form, which increases the complexity of the underlying governing equations and hence the difficulty of their numerical integration. Moreover, the large density difference across the material interface (at least 1000:1 for a gas bubble in a liquid) generates additional problems, compared to a uniform material simulation. Assuming that a non-oscillatory, interface-capturing numerical scheme is employed, thin, but purely numerical mixture zones are generated at the material boundaries, which can give rise to velocity, pressure, and temperature oscillations [23, 24, 25]. Even if the velocity and pressure oscillations are eliminated (e.g., by an energy correction step [23, 25] or by augmenting the Euler system of equations with equations evolving parameters of the equation of state [26, 27, 28, 29]), the temperature oscillations may persist, as demonstrated in previous work by the authors (Fig. 4 in [25]). This could be attributed to the fact that the specific heat of the artificial mixture cannot be physically derived and hence must be constructed mathematically. Independent of their origin, the temperature oscillations would be destructive in any ignition studies, as they would spuriously activate the temperature-dependent reaction rate, thus generating false ignition. It is, thus, important to ensure that spurious numerical artefacts are either removed or do not arise in the first place.
Most work found in the literature that present temperature fields is either focusing on the temperature inside the cavity only, done in two-dimensions or use idealised equations of state. In this work, we overcome the difficulties in numerically simulating the cavity collapse mentioned above (including the spurious temperature oscillations) by exercising a mathematical model proposed by the authors in previous work [25], allowing for a complete shock–cavity interaction simulation. We simulate the three-dimensional collapse of isolated air cavities in nitromethane, using the Cochran–Chan equation of state for the explosive and demonstrating the validity of this equation of state in the regime of pressures found in the simulations by comparing to experiment. The temperature fields recovered are also free from spurious oscillations and the 1000:1 density difference between the cavity and ambient material is captured directly. In the first instance, we consider the induced temperature field in the explosive in the absence of chemical reactions so that hydrodynamical effects are elucidated. However, the oscillation-free temperature fields will allow for the use of a temperature-dependent reaction rate law in future work. In this work, we move beyond solely reporting potential hot spot loci and identifying high-temperature peaks; we look in depth how the mechanical effects (e.g., the generation and propagation of waves) lead to the thermodynamical effects (e.g., elevation of temperatures) that generate the localised hot spots. Each wave generated in the complex cavity collapse scenario is labelled and its effect on the temperature field is thereafter determined. In experiments, such detail of study is limited by instrumentation; the locus of luminescence downstream the cavity is noted as the main ignition site and the jet impact as the principal ignition mechanism (e.g., [1, 30, 31]). In numerical studies, where more detailed wave patterns can be obtained, the shock waves produced upon jet impact are considered as a single wave moving outwards from the cavity remains (e.g., [6]). We demonstrate, however, that two distinct shock wave components can be identified upon collapse; one travelling downstream and one travelling upstream. It is also demonstrated that it is the upstream-travelling wave that leads to the highest temperature locus in collapse scenarios of the incident shock pressure considered here. We identify the regions with temperatures that are higher than the post-shock temperature and are candidates for ignition loci in reactive simulations. In this process, we report a new hot spot location, in the Mach stem generated at late stages of the collapse. This hot spot is omitted in previous studies (e.g., [6]) but is considered here in detail as its effect could be similar to that of the principal hot spot along the cavity centreline. By comparing to the equivalent two-dimensional cavity collapse, we demonstrate also the importance of performing this study in a three-dimensional framework, as the two-dimensional simulations are shown to under-predict the temperature fields in some stages and over-predict them in others, something that could lead to no or false ignition sites.
In Part II of this work, that will follow in the future, the reactions in nitromethane will be activated and the ignition of the material can then be traced back to the elevation of the temperature fields and accountable waves described here.
2 Mathematical and physical model
2.1 Equations of state
Equation of state parameters for nitromethane and air
Equation of state parameters | \(\varGamma _0\) (–) | \(\mathcal {A}\) (GPa) | \(\mathcal {B}\) (GPa) | \(\mathcal {E}_1\) (–) | \(\mathcal {E}_2\) (–) | \(\rho _0\) (\(\hbox {kg m}^{-3}\)) | \(c_v \) (\(\hbox {J kg}^{-1}\,\hbox {K}^{-1}\)) |
---|---|---|---|---|---|---|---|
Nitromethane [32] | 1.19 | 0.819 | 1.51 | 4.53 | 1.42 | 1134 | 1714 |
Air | 0.4 | – | – | – | – | – | 718 |
Initial conditions for the shock-induced cavity collapse in water considered for validation purposes
Material | \(\rho _1\) | \(\rho _{2}\) | u | v | p | \(z_1\) | |
---|---|---|---|---|---|---|---|
\(x<0.6\) | Shocked water | \(1.59\times 10^{-3}\) | 1.325 | 68.0525 | 0.0 | 19,153 | \(10^{-6}\) |
\(x\ge 0.6\) | Ambient water | \(1.2\times 10^{-3}\) | 1.0 | 0.0 | 0.0 | 1.0 | \(10^{-6}\) |
Bubble | Air | \(1.2\times 10^{-3}\) | 1.0 | 0.0 | 0.0 | 1.0 | 1–10\(^{-6}\) |
2.2 Recovery of temperature
For this work, substitution of the parameters of the equation of state for nitromethane and imposing an initial temperature of \(298\,\hbox {K}\) for \(\rho =\rho _0\) gives \(T_0=0\). This is in line with other work using the Cochran–Chan equation of state, where \(T_0\) takes zero or very small values [33, 34, 35, 36]. The form (6) gives temperatures that match experiments as demonstrated in the validation section, but for other materials or other equations of state (e.g., shock Mie–Grüneisen), care should be taken as a different reference curve (as per 7) would be necessary.
The ideal gas equation of state results in the overheating of the gas inside the cavity since high pressures are reached within the cavity during the collapse process. However, at these time-scales, heat transfer would not physically take place and thus the cavity temperature would not affect the ambient nitromethane temperature. Since temperatures inside the cavity are not of interest for this work, they are not presented henceforth.
Note that the two-phase nature of the model allows for large (>1000:1) density gradients to be sustained across material boundaries and both the velocity and temperature fields are maintained oscillation-free.
3 Validation
System (1) is integrated numerically using a high-resolution shock-capturing numerical scheme, namely the MUSCL-Hancock finite volume method with an underlying HLLC Riemann solver. Hierarchical, structured, adaptive mesh refinement (AMR) is used to dynamically increase the resolution locally [37].
The aim of this section is to validate the resulting code using test problems with known solutions and to assess the suitability of the physical models to predict realistic temperature fields.
3.1 Air pocket collapsing in water
A domain of size \((x,y)\in [-6,6]\times [0,6]\) is considered with base resolution \(250\times 125\) and three levels of AMR, doubling the resolution with each refinement level, leading to an effective resolution of \(2000\times 1000\) cells and an air bubble of initial diameter \(D=6\). The initial conditions for this test are given in non-dimensional form in Table 2.
The air is modelled as an ideal gas and the water as a stiffened gas. Both equations of state can be written in the Mie–Grüneisen form (3), with \(p_{\text {ref}}(\rho )=e_{\text {ref}}(\rho )=0\) and \(\varGamma _0 = \gamma - 1 = 0.4\) for the air and \(p_{\text {ref}}(\rho )=6000\), \(e_{\text {ref}}(\rho )=0\), and \(\varGamma _0 = \gamma - 1 = 3.4\) for the water. In this work, only the upper part of the bubble is simulated; thus, a reflective boundary condition is used at the bottom horizontal domain boundary. All other domain boundary conditions are taken to be transmissive.
In Fig. 3a, the evolution of the bubble boundary under the effect of the incident shock wave is shown at time instances \(t=1\), 1.5, 2, 2.5, 3, 3.5, and 4. The top half of the image (\(y>0\)) shows results from this work, and the bottom half (\(y<0\)) shows results from [39]. The two sets of results match reasonably well, and small differences are attributed to the fact that a diffused interface method (shock-capturing) is used in this work whereas a shock-tracking method is used in [39]. In Fig. 3b we present the evolved, non-dimensional, normalised with respect to the bubble diameter width and height of the bubble. We compare the width and height obtained from this work to the results of [38, 39].
3.2 Shocked-nitromethane temperature
Initial conditions for the shock-induced cavity collapse in inert nitromethane considered in this work
Material | \(\rho _1\) | \(\rho _{2}\) (\(\hbox {kg m}^{-3}\)) | u (\(\hbox {kg m}^{-3}\)) | p (\(\hbox {m\,s}^{-1}\)) | \(z_1\) (Pa) | |
---|---|---|---|---|---|---|
\(x<100\,\upmu \hbox {m}\) | Shocked nitromethane | 2.4 | 1934.0 | 2000.0 | \(10.98\times 10^{9}\) | \(10^{-6}\) |
\(x\ge 100\,\upmu \hbox {m}\) | Ambient nitromethane | 1.2 | 1134.0 | 0.0 | \(1\times 10^{5}\) | \(10^{-6}\) |
Bubble | Air | 1.2 | 1134.0 | 0.0 | \(1\times 10^{5}\) | 1–10\(^{-6}\) |
The solid circles ( Open image in new window ) in Fig. 4 present the temperature of neat nitromethane predicted from our simulations, calculated by expression (6). It is important to note the wide spread of the results from different sources and the fact that there is no indication of experimental error. Nevertheless, the post-shock temperatures predicted from our simulations are well within the bounds of this compilation, and they are closest to the ones by Lysne and Hardesty [40]. This ensures the validity of the temperature field for the explosive material, before the inclusion of cavities.
It should be noted that using \(c_v\) and \(\varGamma \) as functions of density and temperature could improve the temperature calculation, as well as using other methods for temperature calculation, e.g., following the work of Winey et al. [41] or Desbiens et al. [50]. As suggested by Fig. 4, the latter would give higher temperatures than the current method, for the same shock pressure.
4 The collapse of a single cavity in liquid non-reacting nitromethane
In this section, an isolated air-filled cavity of radius \(0.08\,\hbox {mm}\)^{2} collapsing in non-reactive liquid nitromethane due to a 10.98 GPa incident shock wave (ISW) is considered. The air inside the cavity is modelled by the ideal gas equation of state, and the nitromethane is modelled by the Cochran–Chan equation of state as described in Sect. 2.1, with parameters as listed in Table 1. As the ignition and thermal runaway in an explosive are attributed to the complex interaction between nonlinear gas dynamics and chemistry, it is intuitive to consider in the first instance the induced temperature field in the explosive in the absence of chemical reactions. This will allow the purely gas-dynamical effects to be elucidated. The simulation is performed in three dimensions, with effective grid size \(\mathrm {d}x=\mathrm {d}y=\mathrm {d}z=0.3125\,\upmu \hbox {m}\), selected after the convergence study presented in Appendix. The initial conditions for the simulation are given in Table 3, corresponding to the sketch of Fig. 1.
4.1 Early stages of the three-dimensional cavity collapse
In order to study the complex wave pattern emanating from the cavity collapse process, xz-slices through the centre of the cavity are taken. The xy-plane plots show the same results and are thus omitted. As the cavity collapse is symmetric about the x-centreline, the lower part of the cavity is omitted. However, to give the three-dimensional perspective of the set-up, we first present in Fig. 5 a couple of indicative three-dimensional plots of the shock–cavity collapse in terms of the nitromethane temperature field. Figure 6 illustrates the mock-schlieren plots on this plane, for the early stages of the collapse process. The horizontal axis gives the x-position and the vertical axis the z-position, both in \(\upmu \hbox {m}\).
Before the jet is fully formed, the air shock \(\mathrm {S}_2\) traverses a small part of the cavity and its upper part moves downwards due to the high pressure around the upper part of the cavity. This results in self-focusing of the shock, leading to a separation of the upper and lower parts of the wave, labelled \(\mathrm {S}_{2\mathrm {A}}\) and \(\mathrm {S}_{2\mathrm {B}}\) in Fig. 6c, and a kink where the two parts are connected. Two shocks, \(\mathrm {S}_3\) and \(\mathrm {S}_4\), emanate from the kink (Fig. 6d). The air shock travels faster than the ISW and the upper part of \(\mathrm {S}_2\) forms an inward moving shock in the air, \(\mathrm {S}_5\), and an outward moving shock in the nitromethane, \(\mathrm {S}_6\) (Fig. 6d). Waves \(\mathrm {S}_4\) and \(\mathrm {S}_5\) interact inside the cavity, while a secondary kink and two more shock waves are generated along \(\mathrm {S}_5\), as seen in Fig. 6e–f. In Fig. 6f, the lower part of the air shock (\(\mathrm {S}_{2\mathrm {B}}\)) is undergoing a transmission/reflection process^{3} upon reaching the front cavity face, while the upper part (\(\mathrm {S}_{2\mathrm {A}}\)) has already completed this process. The most interesting waves in this case are the ones emanating from the interaction of \(\mathrm {S}_{2\mathrm {B}}\) with the downstream cavity wall. These are the shock labelled \(\mathrm {S}_7\), travelling downstream in the ambient nitromethane and the shock wave labelled \(\mathrm {S}_8\) travelling upstream in the cavity (Fig. 6g).
The last row of Fig. 6 presents the stages close to the collapse time of the cavity. Fig. 6g in particular, illustrates the waves in the system just before the jet reaches the downstream cavity wall. Upon reaching this wall^{4}, two new shock waves are generated in the nitromethane: a downstream-travelling shock wave labelled as \(\mathrm {S}_9\) and an upstream-travelling shock wave labelled as \(\mathrm {S}_{10}\), both shown in Fig. 6h. Other numerical studies do not distinguish between these two parts of the waves and present it as a single “hammer” shock (e.g., [6]). However, distinguishing between the two will be proven important in the following sections when the temperature field is studied. In the 3D-space, the waves \(\mathrm {S}_7\), \(\mathrm {S}_9\), and \(\mathrm {S}_{10}\) can be considered as spherical caps with different centres, radii, and heights. Upon collapse, the cavity forms a toroid of trapped air. On each two-dimensional slice this phenomenon is seen as splitting of the cavity in two lobes. Any gas that was in the region between the jet and the downstream cavity wall before the collapse is pushed into the toroid (or lobes), where it is compressed further as time passes. This violent compression results in another shock wave labelled as \(\mathrm {S}_{11}\) in Fig. 6i travelling upwards in the lobe [51] and as this passes over the front cavity wall, it generates the shock wave \(\mathrm {S}_{11\mathrm {B}}\) travelling in nitromethane. In the same figure, a liquid infusion zone \(\mathrm {Z}_1\) is illustrated. This is a zone created by the liquid penetrating into the gas region due to the high pressure acting on the liquid in this area and obtains a toroidal shape in 3D-space. As this zone is treated as a mixture zone by the mathematical model, its thermodynamic details are open to question (similarly in [51]).
4.2 Late stages of the three-dimensional cavity collapse
The wave patterns emerging at the late stages of the collapse process are complex; hence, planar mock-schlieren plots remain the most convenient means to visualise them (Figs. 7, 8). In Fig. 7a, the air shock \(\mathrm {S}_8\) is seen to reach the downstream side of the lobe. Its interaction with the material interface results in a shock wave traversing the lobe, \(\mathrm {S}_{13}\), and a shock travelling in the liquid, \(\mathrm {S}_{12}\), (see Fig. 7b, c) obtaining a spherical-cap shape in the 3D space. The shock wave \(\mathrm {S}_{11}\) travels upwards in the lobe and interacts obliquely with wave \(\mathrm {S}_{13}\), resulting in the appearance of a new pair of weak shock waves, labelled \(\mathrm {S}_{13\mathrm {A}}\) in Fig. 7b. As \(\mathrm {S}_{11}\) continues its upward travel, generating \(\mathrm {S}_{11\mathrm {B}}\), it also interacts with the ISW (\(\mathrm {S}_1\)) and this complex process leads to the formation of \(\mathrm {S}_{14}\). While moving upwards \(\mathrm {S}_{11}\) also interacts with \(\mathrm {S}_{13}\) and other weak waves that are present in the lobe forming a front labelled \(\mathrm {S}_{15}\). Upon reaching the end of the lobe, it undergoes a transition/reflection process again resulting in a spherical-cap wave (\(\mathrm {S}_{16}\)) in the liquid and a different spherical-cap wave, \(\mathrm {S}_{17}\), (Fig. 7e) in the lobe. The transmitted wave \(\mathrm {S}_{16}\) combines quickly with \(\mathrm {S}_{14}\) and the two move together outwards from the lobe, thus labelled as \(\mathrm {S}_{14,16}\) in Fig. 7e. This wave then combines with \(\mathrm {S}_{12}\), as seen in Fig. 7f, and is thus labelled as \(\mathrm {S}_{12,14,16}\). Meanwhile, several reflection/transmission processes take place at the lobe–nitromethane interface, which lead to the lobe closing up due to its rapid compression. As a result, such processes are difficult to track from this point onward (e.g., wave \(\mathrm {S}_{18}\) in Fig. 7e). In general, the waves transmitted from the lobe continue to expand outwards and the ones traversing the lobe compress the cavity gas further.
Figure 8a illustrates waves \(\mathrm {S}_{19}\) and \(\mathrm {S}_{20}\), which have been generated during late-time transmission/reflection processes at the lobe boundary. The downstream-travelling wave generated upon the collapse (\(\mathrm {S}_9\)) interacts with the ISW and changes shape, thus labelled now as \(\mathrm {S}_{9\mathrm {A}}\) and \(\mathrm {S}_{9\mathrm {B}}\) (Fig. 8b). \(\mathrm {S}_{19}\) interacts with \(\mathrm {S}_{9\mathrm {A}}\), and it is similarly split in two parts, \(\mathrm {S}_{19\mathrm {A}}\) and \(\mathrm {S}_{19\mathrm {B}}\), as illustrated in Fig. 8b. New waves, \(\mathrm {S}_{21}\) and \(\mathrm {S}_{22},\) are generated by more transmission/reflection processes at the lobe boundary, and \(\mathrm {S}_{22}\) is also split into two parts, \(\mathrm {S}_{22\mathrm {A}}\) and \(\mathrm {S}_{22\mathrm {B}}\), due to its interaction with the upstream-travelling wave generated upon cavity collapse, namely \(\mathrm {S}_{10}\) (Fig. 8c). Waves \(\mathrm {S}_{23\mathrm {A}}\) and \(\mathrm {S}_{23\mathrm {B}}\) are generated by the interaction of the lower part of the ISW (\(\mathrm {S}_{1\mathrm {B}}\)) with the lobe. At this point, the ISW has already been split in two parts (\(\mathrm {S}_{1\mathrm {A}}\) and \(\mathrm {S}_{1\mathrm {B}}\)) by its interaction with \(\mathrm {S}_9\) (Fig. 8c, d). \(\mathrm {S}_{23\mathrm {C}}\) emerges from the lower side of the lobe and merges with \(\mathrm {S}_{23\mathrm {A}}\) and \(\mathrm {S}_{23\mathrm {B}}\). In Fig. 8f, two new waves are seen to emanate from the lobe, labelled \(\mathrm {S}_{24}\) and \(\mathrm {S}_{25}\). As the ISW continues to interact with \(\mathrm {S}_{9\mathrm {A}}\) and \(\mathrm {S}_{9\mathrm {B}}\), a Mach stem region \(\mathrm {Z}_3\) is formed (Fig. 8e). This new region, often omitted in the literature, will be seen in the following sections to play an important role in the potential ignition of nitromethane. It should be noted, however, that in cases where the incident shock wave is weak (e.g., 100 MPa in [9] and 1.9 GPa in [8]), it traverses the cavity completely well before jet impact occurs and thus this Mach stem does not occur.
4.3 Temperature distribution during the early stages of the collapse
Having studied in detail the generation of the several waves that appear in the collapse process, we will look now into the effect they have on the nitromethane temperature field. When nitromethane is shocked to 10.98 GPa, it attains a temperature of 1263 K, as illustrated in Fig. 9a. Note that since we are only interested in the nitromethane temperature and to facilitate the interpretation of the results, the cavity region is masked out in the temperature plots of this work. In the early stages of the collapse, the rarefaction wave \(\mathrm {R}_1\) generated by the interaction of the ISW with the cavity boundary (see Fig. 6a), lowers the temperature of nitromethane upstream of the cavity. Specifically, the temperature is distributed according to the distribution of density in the rarefaction wave. The air shock transmitted into the liquid, \(\mathrm {S}_7\) (Fig. 6g), heats the traversed nitromethane region slightly, raising its temperature from 298 K to about 310 K seen in the inset of Fig. 9b.
Figure 10 shows the temperature field in nitromethane and the isotherms of over-temperature, during stages close to the collapse time. Over-temperature is defined as the local nitromethane temperature minus the nitromethane post-shock temperature: \(T_{\text {NM}} - 1263\,\hbox {K}\) in this case. This definition is in fact a play on the term “over-pressure” often used in the literature (e.g., [14]).
Figure 10a illustrates the temperature distribution just before collapse. The highest temperature at this stage (1263 K) is found upstream of the ISW. Note that the over-temperature contours are not plotted at this stage as they have negative values. As soon as the cavity collapses, the new shock waves generated (waves \(\mathrm {S}_9\) and \(\mathrm {S}_{10}\) in Fig. 6h) heat the liquid nitromethane above the post-shock temperature, as seen in Fig. 10b. Waves \(\mathrm {S}_9\) and \(\mathrm {S}_{10}\) initially generate over-temperatures of the range 0–400 K downstream and of the range 0–1700 K upstream of the cavity, in regions we will call front hot spot (FHS) and back hot spot (BHS). In a similar manner, we label the waves generating these hot spots; we call the wave \(\mathrm {S}_9\) front collapse shock wave (FCSW) as it is the wave generating the FHS and the wave \(\mathrm {S}_{10}\) back collapse shock wave (BCSW) as it is the wave generating the BHS. As the BCSW travels outwards, it traverses a region of nitromethane that has already been shocked by the ISW, and as a result, it leads to a generally higher temperature in the BHS than the temperature in the FHS, which is a region that has not already been compressed. As shown in Fig. 10c, over-temperature of the range 0–1897 K is observed upstream of the cavity, in the BHS, while over-temperature of the range 0–723 K is observed downstream of the cavity, in the FHS. The inner contours are the ones with the higher over-temperature value but enclose smaller areas.
4.4 Temperature distribution during the late stages of the collapse
In Fig. 12a, the temperature around the lobe is seen to have been affected by the RW. At this point, sample temperatures around the lobe reach values of about 650–780 K. In Fig. 12b, the shock wave \(\mathrm {S}_{12}\) exits the lobe, gets linked with \(\mathrm {S}_{14,16}\) and heats the nitromethane as it travels outwards from the lobe. At this point, sample temperatures in the region traversed by the wave \(\mathrm {S}_{12,14,16}\) are in the range of 679–745 K.
Meanwhile, region \(\mathrm {Z}_2\) (Fig. 7f) is formed. This zone does not play a significant role in increasing the temperature (Fig. 12c), yet, as nitromethane is heated only up to about 760 K in this region. The maximum over-temperature is 1570 K and is found in the BHS. The maximum over-temperature in the FHS reaches 750 K.
In Fig. 12c, the growth of wave \(\mathrm {S}_{12,14,16}\) generates a new over-temperature region upstream of the cavity, part of which is shown to be bounded by the green over-temperature contour. An isotherm of over-temperature 0 K enclosing a region of maximum temperature 1345 K is seen in the same figure.
As more shock waves emanate from the lobe, new regions of over-temperature are formed around it (see Fig. 12d). As the wave \(\mathrm {S}_{12,14,16}\) is propagated downwards, it leads to the growth of the over-temperature regions, like the one illustrated by the fuchsia contour in Fig. 12d. Even though only one contour of this region is included in this figure, the nitromethane temperature is increased throughout the whole region traversed by this wave, as inferred by the values of over-temperature in this figure.
Meanwhile, the ISW and the FCSW (\(\mathrm {S}_{1}\) and \(\mathrm {S}_{9}\)) generate zone \(\mathrm {Z}_3\), which we call the Mach stem hot spot (MSHS). This is a high-temperature region which, at this instance, encloses over-temperature contours of values 0–230 K, as seen in Fig. 12d. The highest temperature (2773 K), however, is still observed within the over-temperature contours generated by the BCSW, upstream of the cavity.
The maximum over-temperature (1421 K) is still located within the BHS. However, under other initial conditions (e.g., weaker ISW) not presented in this work, the authors have observed the maximum temperature to move in zone \(\mathrm {Z}_3\) at this stage. The highest over-temperature in the FHS is 640 K.
Figure 11 (bottom left) shows in 3D the high-temperature regions of FHS, BHS, and the very early stages of the generation of the MSHS. Upstream of the cavity, a large region of positive over-temperatures is seen with relatively low over-temperature values, although, compared to the other three regions.
Waves \(\mathrm {S}_{12,14,16}\) and \(\mathrm {S}_{22\mathrm {B}}\) now also travel downwards, enlarging the over-temperature regions, as seen in Fig. 13a. As wave \(\mathrm {S}_{12,14,16}\) is superimposed with the BCSW (\(\mathrm {S}_{10}\)), it generates the over-temperature regions enclosed in dark blue and turquoise, with over-temperature values 361 and 446 K, respectively. The spherical nature of waves \(\mathrm {S}_{12,14,16}\) and \(\mathrm {S}_{22\mathrm {B}}\) leads to the growth of the over-temperature regions generated in a three-dimensional sense, all around the lobe.
Wave \(\mathrm {S}_{26}\) is generated from the reflection of the wave \(\mathrm {S}_{12,14,16}\) at the bottom boundary (Fig. 13b). As a result, the liquid in the region the wave \(\mathrm {S}_{26}\) traverses is shocked for the third time, leading to a temperature of about 1622 K. Part of \(\mathrm {S}_{26}\) is superimposed with the BCSW, leading to a temperature of about 1748 K. The highest temperature in the BHS is now 2600 K, in the FHS 586 K, and in the MSHS 2500 K.
In Fig. 13d, the wave \(\mathrm {S}_{22\mathrm {B}}\) is also reflected at the bottom boundary, generating wave \(\mathrm {S}_{27}\), which is then superimposed with the BCSW and waves \(\mathrm {S}_{22\mathrm {A}}\) and \(\mathrm {S}_{22\mathrm {B}}\). This leads to temperatures of the range 1580–1650 K.
Figure 11 (bottom left) shows in 3D the growth of the four high-temperature regions and also the additional increase in temperature in the back cloud of small over-temperature due to the traversing and superposition of the waves emanating from the lobes along the cavity centreline. The highest temperatures are noted in the BHS and the MSHS, as seen in Fig. 14, and are identified as the contours enclosing temperatures above \({2000}\,\hbox {K}\). These are noted as the most likely regions for observing ignition in reactive simulations. In this figure, the three-quarters of the three-dimensional temperature contour is seen.
5 Evolution on constant latitude lines
It is informative to consider the evolution of the flow field on lines of constant latitude on slices like the ones presented in Figs. 9, 10, 12, and 13. We consider the pressure and temperature of nitromethane along the lines \(y={201}\,\upmu \hbox {m}\) (Fig. 15a, b) giving insight on the FHS and BHS and \(y={290}\,\upmu \hbox {m}\) (Fig. 15c, d) giving insight on the MSHS.
In Fig. 15a (first red), the ISW is seen before interacting with the cavity. The corresponding line in Fig. 15b shows the increase in the temperature in nitromethane due to the shock wave to 1263 K. Upon the interaction of the ISW with the cavity, the pressure upstream of the cavity is lowered due to the RW generated [Fig. 15a (blue)], translated into a decrease in nitromethane temperature [Fig. 15b (blue)]. As the jet is formed and vortices are generated at the back of the cavity, the RW and the jet flow are working against each other, the former towards lowering the pressure and temperature and the latter towards raising them. The raising of the pressure and temperature prevails as the RW travels upstream, while the jet becomes more intense. This is seen in Fig. 15a, b (pink–black).
The FCSW and BCSW are seen in Fig. 15a (orange) and correspond to a downstream-travelling and an upstream-travelling thermal front, respectively, seen in Fig. 15b. These fronts are the ones expected to lead to ignition in reactive simulations. As the temperature rise from the BCSW is higher than that from the FCSW, we expect the BHS to lead to faster reaction than the FHS. In between the two thermal fronts of 15b (orange, grey), the nitromethane temperature is seen to reach 0 K. This is because this region is still occupied by the air of the collapsed cavity; hence, nitromethane does not reside there. The superposition of waves emanating from the two lobes along the centreline of the cavity is seen as two new, upstream pressure and temperature peaks in the second green graph of Fig. 15a, b.
Figure 15c, d shows the evolution of the pressure and nitromethane temperature along the \(y={290}\,\upmu \hbox {m}\) line, at the same time instances as presented in Fig. 15a, b. As the RW takes longer to reach this line, the pressure and temperature seem to maintain their post-shock values for longer (Fig. 15c, d (first red-blue)). The effect of the RW is seen in the pink and light blue curves. The generation of the Mach stem is seen in the second red and second green lines of Fig. 15c, accompanied with the thermal fronts shown in Fig. 15d. This would be another region where ignition is expected to be observed in reactive simulations.
6 Maximum temperature in 2D versus 3D
It is observed that in the three-dimensional simulation, the maximum temperature is seen upon collapse. This agrees with the results observed in the detailed analysis performed in Sect. 4 where the maximum temperature is observed in the BHS. The maximum temperature is seen to decrease after this peak, which also agrees with the earlier observation that the temperature reduces as the front and back hot spots grow. A new peak in the maximum temperature is observed at late stages and this corresponds to the temperature increase due to superposition of waves along the centreline of the cavity. In the two-dimensional simulation, the collapse of the cavity is observed slightly later than in the three-dimensional scenario, leading to a lower temperature rise than in the three-dimensional case. However, the decrease of this temperature after the initial collapse peak is almost identical between the two cases. Of great significance is the fact that the maximum temperature in the two-dimensional simulation is observed in the late stages of the collapse.
The maximum temperature results in the two- and three-dimensional configurations follow the same trend, although the first peak temperature is under-predicted and the second peak temperature is over-predicted in the two-dimensional simulations. This would be of great importance in reactive simulation scenarios as, depending on the details of the reaction rate law, it could give the difference of ignition in 3D and no ignition in 2D (at the first peak) or even false late ignition (at the second peak) in 2D. This plot also highlights the importance of the detailed study of the waves and corresponding temperature fields as presented in Sect. 4, as the maximum temperature cannot be entirely accounted for without the detailed wave-pattern analysis.
7 Conclusions
Following the validation, we study in detail the shock-induced cavity collapse in inert liquid nitromethane in three dimensions. We follow the interaction of the incident shock wave with the cavity and the generation of waves during the collapse. For ease of interpretation, we split the collapse phenomenon into two regimes: early stages and late stages. We follow the events leading to the generation of locally high temperatures and identify the effect each wave has on the nitromethane temperature field, something that would be very difficult to achieve experimentally. Moreover, numerical studies on this are very limited, as several challenges have to be overcome for this to be possible, as mentioned in the introduction of this work. We also define as over-temperature the difference between the local nitromethane temperature and the post-shock nitromethane temperature. This concept identifies potential regions that could lead to ignition due to cavity collapse that would not ignite in a neat material shocked by the same shock loading. We study the temperature field using plots on two-dimensional slices of the domain, one-dimensional, constant latitude lines on these slices, as well as two- and three-dimensional temperature and over-temperature contours.
Commonly in the literature, it is suggested that the locus of highest temperature is downstream of the cavity, due to the collapse. We demonstrate that upon collapse, two shock wave components are generated that lead to two high-temperature loci. The downstream-travelling shock wave (FCSW) leads to the generation of a high-temperature region downstream of the cavity (FHS) and the upstream-travelling shock wave (BCSW) leads to the generation of a high-temperature region upstream of the cavity (BHS). We identify that, in fact, the highest temperature during the collapse is observed in the BHS upstream of the cavity. This is attributed to the fact that this region is shocked twice: once by the ISW before the collapse and once by the BCSW after the collapse. In contrary, the FHS region is only shocked once, by the FCSW having similar strength as the BCSW. During the early stages of the collapse, temperatures more than 2.5 times of the post-shock temperature are observed in the BHS. In the FHS, temperatures of 1.6 times the post-shock temperatures are observed.
A considerable amount of attention is often given to the shock waves emanating from the lobes due to multiple wave and material interface interactions. It is identified here, though, that these waves do not contribute much to the temperature elevation, leading to temperature increases of 0–100 K.
Another region identified as a high-temperature locus with the potential to sustain a hot spot in reactive simulations is the Mach stem region generated at late stages after the collapse. This region is neglected in the literature. However, we demonstrate that the temperatures observed in the MSHS are higher than the temperatures in the FHS and comparable to the temperatures in the BHS. In particular, temperatures of more than two times the post-shock temperatures are seen in the MSHS.
A final region with positive over-temperatures is identified far upstream, denoted as rear over-temperature region. Initially, this region attains temperatures higher than the post-shock temperature due to the jet flow during the collapse. At late times after the collapse, however, this is also the region where the waves emanating from the lobes are superimposed. For the duration of our simulations, this superposition leads to a temperature increase of \(\sim {450}\,\hbox {K}\).
The importance of performing three-dimensional simulations compared to two-dimensional ones is demonstrated in the final section. We study the maximum temperature observed over time in the computational domain, and we conclude that the two-dimensional scenario could lead to under-predicting the initiation time or predict false late-time ignition.
The identified positive over-temperature regions will be studied in the second part of this work where three-dimensional reactive simulations will be used to clarify which of these in fact lead to ignition. Having studied the hydrodynamic effects of the collapse on the temperature field, in Part II, we study the additional effect of chemical reactions in the time-scales and length-scales of the configurations under consideration.
Footnotes
- 1.
Note that symbol \(z_i\) refers to the volume fraction of material i and should not be confused with the z axis of the coordinate system.
- 2.
Typical size of large cavities used in mining applications.
- 3.
When a shock wave travelling in a low impedance material reaches a material boundary ahead of which a material of higher impedance is encountered, two new waves are generated; a downstream-travelling shock wave in the high impedance material and an upstream-travelling shock wave in the lower impedance material. In short, we call this a transmission/reflection process.
- 4.
We refer to this event as the time of collapse.
Notes
Acknowledgements
This project was kindly funded by Orica Limited. The authors also benefited from conversations with A. Minchinton, S.K. Chan, and I.J. Kirby.
References
- 1.Bourne, N., Field, J.: Shock-induced collapse of single cavities in liquids. J. Fluid Mech. 244(1), 225–240 (1992). https://doi.org/10.1017/S0022112092003045 CrossRefGoogle Scholar
- 2.Dear, J., Field, J.: A study of the collapse of arrays of cavities. J. Fluid Mech. 190(409), 172 (1988). https://doi.org/10.1017/S0022112088001387 CrossRefGoogle Scholar
- 3.Swantek, A., Austin, J.: Collapse of void arrays under stress wave loading. J. Fluid Mech. 649, 399–427 (2010). https://doi.org/10.1017/S0022112009993545 CrossRefGoogle Scholar
- 4.Swantek, A., Shukla, R., Austin, J.: Effect of loading wave profile on hydrodynamic void collapse in detonation initiation. 48th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition, AIAA Paper 2010-771 (2010). https://doi.org/10.2514/6.2010-771
- 5.Mader, C.: Numerical modeling of detonations. Los Alamos Series in Basic and Applied Sciences, vol. 1. University of California Press, Berkeley (1979)Google Scholar
- 6.Bourne, N., Milne, A.: On cavity collapse and subsequent ignition. In: Proceedings of the Twelfth Symposium (International) on Detonation, pp. 213–219. Office of Naval Research (2002)Google Scholar
- 7.Bourne, N., Milne, A.: The temperature of a shock-collapsed cavity. Proc. R. Soc. Lond. Ser. A Math. Phys. Eng. Sci. 459(2036), 1851–1861 (2003). https://doi.org/10.1098/rspa.2002.1101 MathSciNetCrossRefGoogle Scholar
- 8.Ball, G., Howell, B., Leighton, T., Schofield, M.: Shock-induced collapse of a cylindrical air cavity in water: a free-Lagrange simulation. Shock Waves 10(4), 265–276 (2000). https://doi.org/10.1007/s001930000060 CrossRefGoogle Scholar
- 9.Hawker, N., Ventikos, Y.: Interaction of a strong shockwave with a gas bubble in a liquid medium: a numerical study. J. Fluid Mech. 1(1), 1–39 (2012). https://doi.org/10.1017/jfm.2012.132 CrossRefGoogle Scholar
- 10.Lauer, E., Hu, X., Hickel, S., Adams, N.: Numerical investigation of collapsing cavity arrays. Phys. Fluids 24, 052,104 (2012). https://doi.org/10.1063/1.4719142 CrossRefGoogle Scholar
- 11.Michael, L., Nikiforakis, N., Bates, K.: Numerical simulations of shock-induced void collapse in liquid explosives. In: 14th International Detonation Symposium, pp. 1127–1136. Office of Naval Research (2010)Google Scholar
- 12.Betney, M., Tully, B., Hawker, N., Ventikos, Y.: Computational modelling of the interaction of shock waves with multiple gas-filled bubbles in a liquid. Phys. Fluids (1994–present) 27(3), 036101 (2015). https://doi.org/10.1063/1.4914133 CrossRefGoogle Scholar
- 13.Ozlem, M., Schwendeman, D., Kapila, A., Henshaw, W.: A numerical study of shock-induced cavity collapse. Shock Waves 22, 1–29 (2012). https://doi.org/10.1007/s00193-011-0352-9 CrossRefGoogle Scholar
- 14.Kapila, A., Schwendeman, D., Gambino, J., Henshaw, W.: A numerical study of the dynamics of detonation initiated by cavity collapse. Shock Waves 25(6), 545–572 (2015). https://doi.org/10.1007/s00193-015-0597-9 CrossRefGoogle Scholar
- 15.Michael, L., Nikiforakis, N.: The temperature field around collapsing cavities in condensed phase explosives. In: 15th International Detonation Symposium, pp. 60–70. Office of Naval Research (2014)Google Scholar
- 16.Kittell, D.E., Yarrington, C.D.: A physically-based Mie–Grüneisen equation of state to determine hot spot temperature distributions. Combust. Theor. Model. 20(5), 941–957 (2016). https://doi.org/10.1080/13647830.2016.1201145 MathSciNetCrossRefGoogle Scholar
- 17.Menikoff, R.: Pore collapse and hot spots in HMX. In: AIP Conference Proceedings, vol. 706, pp. 393–396. AIP (2004). https://doi.org/10.1063/1.1780261
- 18.Tran, L., Udaykumar, H.: Simulation of void collapse in an energetic material, Part 2: Reactive case. J. Propuls. Power 22(5), 959–974 (2006). https://doi.org/10.2514/1.13147 CrossRefGoogle Scholar
- 19.Tran, L., Udaykumar, H.: Simulation of void collapse in an energetic material, Part 1: Inert case. J. Propuls. Power 22(5), 947–958 (2006). https://doi.org/10.2514/1.13146 CrossRefGoogle Scholar
- 20.Kapahi, A., Udaykumar, H.: Dynamics of void collapse in shocked energetic materials: physics of void–void interactions. Shock Waves 23(6), 537–558 (2013). https://doi.org/10.1007/s00193-013-0439-6 CrossRefGoogle Scholar
- 21.Rai, N.K., Schmidt, M.J., Udaykumar, H.: Collapse of elongated voids in porous energetic materials: Effects of void orientation and aspect ratio on initiation. Phys. Rev. Fluids 2(4), 043201 (2017). https://doi.org/10.1103/PhysRevFluids.2.043201
- 22.Rai, N.K., Schmidt, M.J., Udaykumar, H.: High-resolution simulations of cylindrical void collapse in energetic materials: Effect of primary and secondary collapse on initiation thresholds. Phys. Rev. Fluids 2(4), 043202 (2017). https://doi.org/10.1103/PhysRevFluids.2.043202
- 23.Banks, J., Schwendeman, D., Kapila, A., Henshaw, W.: A high-resolution Godunov method for compressible multi-material flow on overlapping grids. J. Comput. Phys. 223(1), 262–297 (2007). https://doi.org/10.1016/j.jcp.2006.09.014 MathSciNetCrossRefGoogle Scholar
- 24.Kapila, A., Schwendeman, D., Bdzil, J., Henshaw, W.: A study of detonation diffraction in the ignition-and-growth model. Combust. Theor. Model. 11(5), 781–822 (2007). https://doi.org/10.1080/13647830701235774 MathSciNetCrossRefGoogle Scholar
- 25.Michael, L., Nikiforakis, N.: A hybrid formulation for the numerical simulation of condensed phase explosives. J. Comput. Phys. 316, 193–217 (2016). https://doi.org/10.1016/j.jcp.2016.04.017 MathSciNetCrossRefGoogle Scholar
- 26.Shyue, K.: An efficient shock-capturing algorithm for compressible multicomponent problems. J. Comput. Phys. 142(1), 208–242 (1998). https://doi.org/10.1006/jcph.1998.5930 MathSciNetCrossRefGoogle Scholar
- 27.Shyue, K.: A fluid-mixture type algorithm for compressible multicomponent flow with van der Waals equation of state. J. Comput. Phys. 156(1), 43–88 (1999). https://doi.org/10.1006/jcph.1999.6349 MathSciNetCrossRefGoogle Scholar
- 28.Shyue, K.: A fluid-mixture type algorithm for compressible multicomponent flow with Mie–Grüneisen equation of state. J. Comput. Phys. 171(2), 678–707 (2001). https://doi.org/10.1006/jcph.2001.6801 MathSciNetCrossRefGoogle Scholar
- 29.Wang, S., Anderson, M., Oakley, J., Corradini, M., Bonazza, R.: A thermodynamically consistent and fully conservative treatment of contact discontinuities for compressible multicomponent flows. J. Comput. Phys. 195(2), 528–559 (2004). https://doi.org/10.1016/j.jcp.2003.10.010 MathSciNetCrossRefGoogle Scholar
- 30.Bourne, N., Field, J.: Bubble collapse and the initiation of explosion. Proc. R. Soc. Lond. A 435(1894), 423–435 (1991). https://doi.org/10.1098/rspa.1991.0153 CrossRefGoogle Scholar
- 31.Bourne, N., Field, J.: Explosive ignition by the collapse of cavities. Proc. R. Soc. Lond. Ser. A Math. Phys. Eng. Sci. 455(1987), 2411–2426 (1999). https://doi.org/10.1098/rspa.1999.0410 MathSciNetCrossRefGoogle Scholar
- 32.Saurel, R., Petitpas, F., Berry, R.: Simple and efficient relaxation methods for interfaces separating compressible fluids, cavitating flows and shocks in multiphase mixtures. J. Comput. Phys. 228(5), 1678–1712 (2009). https://doi.org/10.1016/j.jcp.2008.11.002 MathSciNetCrossRefGoogle Scholar
- 33.Genetier, M., Osmont, A., Baudin, G.: Effect of the oxygen balance on ignition and detonation properties of liquid explosive mixtures. In: Journal of Physics: Conference Series, vol. 500, p. 192001. IOP Publishing (2014). https://doi.org/10.1088/1742-6596/500/19/192001 Google Scholar
- 34.Massoni, J., Saurel, R., Baudin, G., Demol, G.: A mechanistic model for shock initiation of solid explosives. Phys. Fluids (1994–present) 11(3), 710–736 (1999). https://doi.org/10.1063/1.869941 MathSciNetCrossRefGoogle Scholar
- 35.Saurel, R., Massoni, J.: On Riemann-problem-based methods for detonations in solid energetic materials. Int. J. Numer. Methods Fluids 26(1), 101–121 (1998). https://doi.org/10.1002/(SICI)1097-0363(19980115)26:1<101::AID-FLD629>3.0.CO;2-0 MathSciNetCrossRefGoogle Scholar
- 36.Shukla, R.K., Pantano, C., Freund, J.B.: An interface capturing method for the simulation of multi-phase compressible flows. J. Comput. Phys. 229(19), 7411–7439 (2010). https://doi.org/10.1016/j.jcp.2010.06.025 MathSciNetCrossRefGoogle Scholar
- 37.Bates, K., Nikiforakis, N., Holder, D.: Richtmyer-Meshkov instability induced by the interaction of a shock wave with a rectangular block of SF\(_6\). Phys. Fluids 19, 036101 (2007). https://doi.org/10.1063/1.2565486 CrossRefGoogle Scholar
- 38.Terashima, H., Tryggvason, G.: A front-tracking method with projected interface conditions for compressible multi-fluid flows. Comput. Fluids 39(10), 1804–1814 (2010). https://doi.org/10.1016/j.compfluid.2010.06.012 MathSciNetCrossRefGoogle Scholar
- 39.Xu, L., Liu, T.: Explicit interface treatments for compressible gas-liquid simulations. Comput. Fluids 153, 34–48 (2017). https://doi.org/10.1016/j.compfluid.2017.03.032 MathSciNetCrossRefGoogle Scholar
- 40.Lysne, P., Hardesty, D.: Fundamental equation of state of liquid nitromethane to 100 kbar. J. Chem. Phys. 59, 6512 (1973). https://doi.org/10.1063/1.1680031 CrossRefGoogle Scholar
- 41.Winey, J., Duvall, G., Knudson, M., Gupta, Y.: Equation of state and temperature measurements for shocked nitromethane. J. Chem. Phys. 113, 7492 (2000). https://doi.org/10.1063/1.1312271 CrossRefGoogle Scholar
- 42.Marsh, S.: LASL Shock Hugoniot Data, vol. 5. University of California Press, Berkeley (1980)Google Scholar
- 43.Delpuech, A., Menil, A.: Raman scattering temperature measurement behind a shock wave. In: Proceedings, American Physical Society Topical Conference on Shock Waves in Condensed Matter (North-Holland, Amsterdam, 1983), pp. 877–882 (1984). https://doi.org/10.1007/978-1-4613-2207-8_129 CrossRefGoogle Scholar
- 44.Dufort, S.: Mesures de températures sous choc par diffusion Raman. Le Journal de Physique Colloques 48(C4), 137–144 (1987). https://doi.org/10.1051/jphyscol:1987409 CrossRefGoogle Scholar
- 45.Cowperthwaite, M., Shaw, R.: \(C_v\)(T) equation of state for liquids. Calculation of the shock temperature of carbon tetrachloride, nitromethane, and water in the 100-kbar region. J. Chem. Phys. 53, 555 (1970). https://doi.org/10.1063/1.1674025 CrossRefGoogle Scholar
- 46.Soulard, L.: Shock polar calculation of inert nitromethane by molecular dynamics simulation. AIP Conference Proceedings 620, p. 173 (2002). https://doi.org/10.1063/1.1483509
- 47.Jones, H.: Equation of state for liquid nitromethane at high pressures. In: AIP Conference Proceedings, vol. 706, pp. 149–152 (2004). https://doi.org/10.1063/1.1780205
- 48.Liu, H., Zhao, J., Ji, G., Gong, Z., Wei, D.: Compressibility of liquid nitromethane in the high-pressure regime. Physica B 382(1), 334–339 (2006). https://doi.org/10.1016/j.physb.2006.03.018 CrossRefGoogle Scholar
- 49.Hervouët, A., Desbiens, N., Bourasseau, E., Maillet, J.: Microscopic approaches to liquid nitromethane detonation properties. J. Phys. Chem. B 112(16), 5070–5078 (2008). https://doi.org/10.1021/jp077250n CrossRefGoogle Scholar
- 50.Desbiens, N., Bourasseau, E., Maillet, J., Soulard, L.: Molecular based equation of state for shocked liquid nitromethane. J. Hazard. Mater. 166(2–3), 1120–1126 (2009). https://doi.org/10.1016/j.jhazmat.2008.12.083 CrossRefGoogle Scholar
- 51.Ozlem, M.: A numerical study of shock induced cavity collapse. PhD Thesis, Rensselaer Polytechnic Institute (2010)Google Scholar
Copyright information
Open AccessThis article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.