Springer Nature is making SARS-CoV-2 and COVID-19 research free. View research | View latest news | Sign up for updates

Quality characterization of dissimilar laser welded joints of Ti6Al4V with AISI 304 by using copper deposition technique

  • 74 Accesses

Abstract

Dissimilar metal welding leads to the development of brittleness in the welded joints due to incompatibility in mechanical and physical properties of the metals to be joined. To overcome such brittleness, suppressing the formation of intermetallic compound is the key factor for attaining reliable welded joints. The present study attempts to find the possibility of obtaining joints of crack-free surface in laser butt welding of Ti6Al4V with AISI 304 stainless steel sheets using intermetallic layer through electroplating process. Laser welding on Ti6Al4V titanium alloy with AISI 304 stainless steel sheets of 5 mm thickness has been performed providing copper as an intermetallic layer using electroplating process. Electroplating of the welding edges of two different materials was carried out with and without adding sulphuric acid in the electrolyte solution. The electroplating results indicate that addition of sulphuric acid in the solution increases the thickness of the coating. Presence of copper at the welding edges provides compatibility between Ti6Al4V and AISI 304 during the laser welding process and reduces brittleness. Laser welding was conducted using 3.5-kW CO2 laser with 3-m/min welding speed. The quality of weldment was characterized by macrostructure analysis by scanning electron microscope (SEM), analysis of composition of weldment by energy dispersive spectroscopy (EDS), phase analysis by X-ray diffraction (XRD), microhardness across the weldment by Vickers hardness tester and estimation of welding strength by dynamic mechanical analyser. Welding strength of around 34 MPa has been obtained and it is quite acceptable.

This is a preview of subscription content, log in to check access.

We’re sorry, something doesn't seem to be working properly.

Please try refreshing the page. If that doesn't work, please contact support so we can address the problem.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20
Fig. 21
Fig. 22
Fig. 23
Fig. 24

References

  1. 1.

    Shanmugarajan B, Padmanabham G (2012) Fusion welding studies using laser on Ti–SS dissimilar combination. Opt Lasers Eng 50(11):1621–1627

  2. 2.

    Dey HC, Ashfaq M, Bhaduri AK, Rao KP (2009) Joining of titanium to 304L stainless steel by friction welding. J Mater Process Technol 209(18–19):5862–5870

  3. 3.

    Welding EB, Handbook ASM (1993) Welding, brazing, and soldering. ASM Int 6:254

  4. 4.

    Tomashchuk I, Sallamand P, Belyavina N, Pilloz M (2013) Evolution of microstructures and mechanical properties during dissimilar electron beam welding of titanium alloy to stainless steel via copper interlayer. Mater Sci Eng A 585:114–122

  5. 5.

    Mudali UK, Rao BA, Shanmugam K, Natarajan R, Raj B (2003) Corrosion and microstructural aspects of dissimilar joints of titanium and type 304L stainless steel. J Nucl Mater 321(1):40–48

  6. 6.

    Ghosh M, Chatterjee S, Mishra B (2003) The effect of intermetallics on the strength properties of diffusion bonds formed between Ti–5.5Al–2.4V and 304 stainless steel. Mater Sci Eng A 363(1–2):268–274

  7. 7.

    Boyer RR (1996) An overview on the use of titanium in the aerospace industry. Mater Sci Eng A 213(1–2):103–114

  8. 8.

    Chen S, Zhang M, Huang J, Cui C, Zhang H, Zhao X (2014) Microstructures and mechanical property of laser butt welding of titanium alloy to stainless steel. Mater Des 53:504–511

  9. 9.

    Church SC, Wild RK (1998) Diffusion bonding of steel to Ti-6Al-4V to produce hard wearing surface layers. J Vac Sci Technol A 16(3):1885–1889

  10. 10.

    Murray JL (1987) Phase diagrams of binary titanium alloys. International, ASM, pp 99–111

  11. 11.

    Pardal G, Ganguly S, Williams S, Vaja J (2016) Dissimilar metal joining of stainless steel and titanium using copper as transition metal. Int J Adv Manuf Technol 86(5–8):1139–1150

  12. 12.

    Li L, Tan C, Chen Y, Guo W, Song F (2013) Comparative study on microstructure and mechanical properties of laser welded-brazed mg/mild steel and mg/stainless steel joints. Mater Des 43:59–65

  13. 13.

    Tan C, Song X, Meng S, Chen B, Li L, Feng J (2016) Laser welding-brazing of mg to stainless steel: joining characteristics, interfacial microstructure, and mechanical properties. Int J Adv Manuf Technol 86(1–4):203–213

  14. 14.

    Hailat MM, Mian A, Chaudhury ZA, Newaz G, Patwa R, Herfurth HJ (2012) Laser micro-welding of aluminum and copper with and without tin foil alloy. Microsyst Technol 18(1):103–112

  15. 15.

    Chen S, Yang D, Li M, Zhang Y, Huang J, Yang J, Zhao X (2016) Laser penetration welding of an overlap titanium-on-aluminum configuration. Int J Adv Manuf Technol 87(9–12):3069–3079

  16. 16.

    Torkamany MJ, Sabbaghzadeh J, Hamedi MJ (2012) Effect of laser welding mode on the microstructure and mechanical performance of dissimilar laser spot welds between low carbon and austenitic stainless steels. Mater Des 34:666–672

  17. 17.

    Ruggiero A, Tricarico L, Olabi AG, Benyounis KY (2011) Weld-bead profile and costs optimisation of the CO2 dissimilar laser welding process of low carbon steel and austenitic steel AISI316. Opt Laser Technol 43(1):82–90

  18. 18.

    Zhao S, Yu G, He X, Hu Y (2012) Microstructural and mechanical characteristics of laser welding of Ti6Al4V and lead metal. J Mater Process Technol 212(7):1520–1527

  19. 19.

    Li Q, Zhu Y, Guo J (2017) Microstructure and mechanical properties of resistance-welded NiTi/stainless steel joints. J Mater Process Technol 249:538–548

  20. 20.

    Lee WB, Kim YJ, Jung SB (2004) Effects of copper insert layer on the properties of friction welded joints between TiAl and AISI 4140 structural steel. Intermetallics 12(6):671–678

  21. 21.

    Lee WB, Jung SB (2004) Effect of microstructure on mechanical properties of friction-welded joints between Ti and AISI 321 stainless steel. Mater Trans 45(9):2805–2811

  22. 22.

    Wang T, Zhang B, Chen G, Feng J (2013) High strength electron beam welded titanium-stainless steel joint with V/cu based composite filler metals. Vacuum 94:41–47

  23. 23.

    Mitelea I, Groza C, Craciunescu C (2013) Copper interlayer contribution on Nd: YAG laser welding of dissimilar Ti-6Al-4V alloy with X5CrNi18-10 steel. J Mater Eng Perform 22(8):2219–2223

  24. 24.

    Chen S, Huang J, Xia J, Zhao X, Lin S (2015) Influence of processing parameters on the characteristics of stainless steel/copper laser welding. J Mater Process Technol 222:43–51

  25. 25.

    Yu XY, Zhou DR, Yao DJ, Lu FG, Xu PQ (2016) Fiber laser welding of WC-co to carbon steel using Fe-Ni invar as interlayer. Int J Refract Met Hard Mater 56:76–86

  26. 26.

    Huang BS, Yang J, Lu DH, Bin WJ (2016) Study on the microstructure, mechanical properties and corrosion behaviour of S355JR/316L dissimilar welded joint prepared by gas tungsten arc welding multi-pass welding process. Sci Technol Weld Join 21(5):381–388

  27. 27.

    Chen HC, Pinkerton AJ, Li L (2011) Fibre laser welding of dissimilar alloys of Ti-6Al-4V and Inconel 718 for aerospace applications. Int J Adv Manuf Technol 52(9–12):977–987

  28. 28.

    Khan MMA, Romoli L, Dini G (2013) Laser beam welding of dissimilar ferritic/martensitic stainless steels in a butt joint configuration. Opt Laser Technol 49:125–136

  29. 29.

    Gao M, Wang ZM, Li XY, Zeng XY (2012) Laser keyhole welding of dissimilar Ti-6Al-4V titanium alloy to AZ31B magnesium alloy. Metall Mater Trans A 43(1):163–172

  30. 30.

    Chen HC, Bi G, Lee BY, Cheng CK (2016) Laser welding of CP Ti to stainless steel with different temporal pulse shapes. J Mater Process Technol 231:58–65

  31. 31.

    Tomashchuk I, Grevey D, Sallamand P (2015) Dissimilar laser welding of AISI 316L stainless steel to Ti6-Al4-6V alloy via pure vanadium interlayer. Mater Sci Eng A 622:37–45

  32. 32.

    Wang T, Zhang B, Wang H, Feng J (2014) Microstructures and mechanical properties of electron beam-welded titanium-steel joints with vanadium, nickel, copper and silver filler metals. J Mater Eng Perform 23(4):1498–1504

  33. 33.

    Gao M, Mei SW, Wang ZM, Li XY, Zeng XY (2012) Characterisation of laser welded dissimilar Ti/steel joint using mg interlayer. Sci Technol Weld Join 17(4):269–276

  34. 34.

    Gao M, Chen C, Wang L, Wang Z, Zeng X (2015) Laser-arc hybrid welding of dissimilar titanium alloy and stainless steel using copper wire. Metall Mater Trans A 46(5):2007–2020

  35. 35.

    Tomashchuk I, Sallamand P, Andrzejewski H, Grevey D (2011) The formation of intermetallics in dissimilar Ti6Al4V/copper/AISI 316L electron beam and Nd:YAG laser joints. Intermetallics 19(10):1466–1473

  36. 36.

    Dehghanghadikolaei A, Fotovvati B (2019) Coating techniques for functional enhancement of metal implants for bone replacement: a review. Materials 12(11):1795

  37. 37.

    Uddin GM, Jawad M, Ghufran M, Saleem MW, Raza MA, Rehman ZU, Arafat SM, Irfan M, Waseem B (2019) Experimental investigation of tribo-mechanical and chemical properties of TiN PVD coating on titanium substrate for biomedical implants manufacturing. Int J Adv Manuf Technol 102(5–8):1391–1404

  38. 38.

    Fotovvati B, Namdari N, Dehghanghadikolaei A (2019) On coating techniques for surface protection: a review. J Manuf Mater Process 3(1):28

  39. 39.

    Dikusar AI, Bobanova ZI, Yushchenko SP, Yakovets IV (2005) Throwing power of a dilute sulfuric acid copper plating electrolyte during intensive electrodeposition. Russ J Electrochem 41(1):82–86

  40. 40.

    Chen TC, Tsai YL, Hsu CF, Dow WP, Hashimoto Y (2016) Effects of brighteners in a copper plating bath on throwing power and thermal reliability of plated through holes. Electrochim Acta 212:572–582

  41. 41.

    Vicenzo A, Cavallotti PL (2002) Copper electrodeposition from a pH3 sulfate electrolyte. J Appl Electrochem 32(7):743–753

  42. 42.

    Mehdi B, Badji R, Ji V, Allili B, Bradai D, Deschaux-Beaume F, Soulié F (2016) Microstructure and residual stresses in Ti-6Al-4V alloy pulsed and unpulsed TIG welds. J Mater Process Technol 231:441–448

  43. 43.

    Gil FJ, Ginebra MP, Manero JM, Planell JA (2001) Formation of α-Widmanstätten structure: effects of grain size and cooling rate on the Widmanstätten morphologies and on the mechanical properties in Ti6Al4V alloy. J Alloys Compd 329(1–2):142–152

  44. 44.

    Jia MT, Zhang DL, Gabbitas B, Liang JM, Kong C (2015) A novel Ti-6Al-4V alloy microstructure with very high strength and good ductility. Scr Mater 107:10–13

  45. 45.

    Kumar K, Masanta M, Sahoo SK (2019) Microstructure evolution and metallurgical characteristic of bead-on-plate TIG welding of Ti-6Al-4V alloy. J Mater Process Technol 265:34–43

Download references

Author information

Correspondence to Suman Chatterjee.

Additional information

Publisher’s note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Appendix

Appendix

Fig. 25
figure25

Residual stress developed in the weldment

Rights and permissions

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Chatterjee, S., Sahoo, S.K., Swain, B. et al. Quality characterization of dissimilar laser welded joints of Ti6Al4V with AISI 304 by using copper deposition technique. Int J Adv Manuf Technol 106, 4577–4591 (2020). https://doi.org/10.1007/s00170-020-04935-5

Download citation

Keywords

  • Dissimilar welding
  • Dynamic mechanical analysis (DMA)
  • Electroplating
  • Intermetallic
  • Stainless steel
  • Titanium alloy