Advertisement

Finite element analysis of ultrasonic assisted milling of SiCp/Al composites

  • Daohui XiangEmail author
  • Zhanli Shi
  • Haoren Feng
  • Bangfu Wu
  • Zhimeng Zhang
  • Yanbin Chen
  • Xiaoxiao Niu
  • Bo Zhao
ORIGINAL ARTICLE
  • 81 Downloads

Abstract

SiCp/Al composites have a poor machinability due to the inclusion of the SiC hard particles. Ultrasonic vibration-assisted processing technology has great advantages in processing hard and brittle materials; however, the process of rupture of particles cannot be effectively observed during the test processing, and a large number of tests increase the cost of the test. Using ABAQUS finite element software, a two-dimensional simulation model of single particle, multi-particle, and homogeneous materials was established to investigate the particle rupture process and the temperature variation during the processing of high volume SiCp/Al composites under different processing parameters. The results show that the application of ultrasound improved the particle rupture effect. Furthermore, an appropriate ultrasonic amplitude inhibited the particle breakage and slowed the crack growth. A smoother particle breaking phenomena was observed with the application of a higher frequency. The temperature of ultrasonic assisted milling was found to be lower than that of traditional milling. The conclusions of the milling test were basically consistent with the simulation results, which prove the correctness and feasibility of the simulation results.

Keywords

Ultrasonic assisted milling Finite element simulation Particle breakage Milling temperature 

Notes

Funding information

This research was supported financially by the National Natural Science Foundation of China (No. 51975188), Henan Provincial Natural Science Foundation of China (No.182300410200), and Open Research Fund of State Key Laboratory of High Performance Complex Manufacturing, Central South University (No. Kfkt2017-09).

References

  1. 1.
    Ozben T, Kilickap E, Cakir O (2008) Investigation of mechanical and machinability properties of SiC particle reinforced Al-MMC. J Mater Process Technol 198:220–225CrossRefGoogle Scholar
  2. 2.
    Huang Y, Ouyang QB, Zhang D (2014) Carbon materials reinforced aluminum composites: A Review. Acta Metall Sin Engl Lett 27(5):775–786CrossRefGoogle Scholar
  3. 3.
    Wang XL, Wei YH (2016) Discussion on the application and development of metal matrix composites in aerospace. Sci Technol Innov 13(6):16–17Google Scholar
  4. 4.
    Gao M, Zhang J, Li J (2012) Feasibility analysis of high-volume fraction SiC/Al mirror application in space optics. Infrared Laser Eng 41(7):1803–1807Google Scholar
  5. 5.
    Hakami F, Pramanik A, Basak AK (2017) Tool wear and surface quality of metal matrix composites due to machining: A review. Proc Inst Mech Eng B J Eng Manuf 231(5):739–752CrossRefGoogle Scholar
  6. 6.
    Nicholls CJ, Boswell B, Davies IJ (2017) Review of machining metal matrix composites. Int J Adv Manuf Technol 90(9):2429–2441CrossRefGoogle Scholar
  7. 7.
    Dambatta YS, Sarhan AD, Sayuti M (2017) Ultrasonic assisted grinding of advanced materials for biomedical and aerospace applications-a review. Int J Adv Manuf Technol 92(9-12):3825–3858CrossRefGoogle Scholar
  8. 8.
    Singh RP, Singhal S (2016) Rotary ultrasonic machining: A review. Mater Manuf Process 31(14):1795–1824CrossRefGoogle Scholar
  9. 9.
    Elhami S, Razfar MR, Farahnakian M (2015) Analytical, numerical and experimental study of cutting force during thermally enhanced ultrasonic assisted milling of hardened AISI 4140. Int J Mech Sci 103(11):158–171CrossRefGoogle Scholar
  10. 10.
    Maurottoa A, Wickkramarachchi CT (2016) Experimental investigations on effects of frequency in ultrasonically-assisted end-milling of AISI 316L: A feasibility study. Ultrasonics 65(2):113–120CrossRefGoogle Scholar
  11. 11.
    Kazuki N, Yu T, Tojiro A, Yasuhiro K, Seiji H (2014) High-precision and high-efficiency micromachining of chemically strengthened glass using ultrasonic vibration. Procedia CIRP 14:389–394CrossRefGoogle Scholar
  12. 12.
    Liang GQ, Zhou XQ, Zhao FF (2016) The grinding surface characteristics and evaluation of particle-reinforced aluminum silicon carbide. Sci Eng Compos Mater 23(6):671–676CrossRefGoogle Scholar
  13. 13.
    Feng PF, Liang GQ, Zhang JF (2014) Ultrasonic vibration-assisted scratch characteristics of silicon carbide-reinforced aluminum matrix composites. Ceram Int 40(7):10817–10823CrossRefGoogle Scholar
  14. 14.
    Lian H, Guo Z (2013) Experimental research of Al6061 on ultrasonic vibration assiated micro-milling. Procedia CIRP 6:561–564CrossRefGoogle Scholar
  15. 15.
    Kadivar MA, Akbari J, Yousefi R (2014) Investigating the effects of vibration method on ultrasonic-assisted drilling of Al/SiCp metal matrix composites. Robot Comput Integr Manuf 30(3):344–350CrossRefGoogle Scholar
  16. 16.
    Wang T, Xie LJ, Wang XB (2015) Simulation study on defect formation mechanism of the machined surface in milling of high volume fraction SiCp/Al composite. Int J Adv Manuf Technol 79(5-8):1185–1194CrossRefGoogle Scholar
  17. 17.
    Chen XL, Xie LJ, Xue X (2017) Research on 3D milling simulation of SiCp/Al composite based on a phenomenological model. Int J Adv Manuf Technol 92(5-8):2715–2723CrossRefGoogle Scholar
  18. 18.
    Liu J, Cheng K, Ding H (2017) Simulation study of the influence of cutting speed and tool-particle interaction location on surface formation mechanism in micromachining SiCp/Al composites. Proceedings of the Institution of Mechanical Engineers,Part C:Journal of Mechanical Engineering Science 232(11):2044-2056Google Scholar
  19. 19.
    Liu J, Cheng K, Ding H (2016) An investigation of surface defect formation in micro milling the 45% SiCp/Al composite. Procedia CIRP 45:211–214CrossRefGoogle Scholar
  20. 20.
    Zhou L, Huang ST, Wang D, Yu XL (2011) Finite element and experimental studies of the cutting process of SiCp/Alcomposites with PCD tools process of SiCp/Al composites with PCD tools. Int J Adv Manuf Technol 52:619–626CrossRefGoogle Scholar
  21. 21.
    He J (2008) Research on ultrasonic vibration cutting of particle reinforced aluminum metal matrix composites. Harbin Institute of Technology, HarbinGoogle Scholar
  22. 22.
    Zhong ZW, Lin G (2006) Ultrasonic assisted turning of an aluminium-based metal matrix composite reinforced with SiC particles. Int J Adv Manuf Technol 27(11-12):1077–1081CrossRefGoogle Scholar
  23. 23.
    Liao TK (2016) Influence of material constitutive model parameters on 2d orthogonal cutting simulation. J Huaqiao Univ 37(5):541–546Google Scholar
  24. 24.
    Zhou CL (2017) Effects of the constitutive model parameters research on finite element simulation of cutting processes. Mod Manuf Eng 1:105–109Google Scholar
  25. 25.
    Ni JM (2014) The coupling of the thermal and mechanical influence on the surface integrity by the high speed outer cylindrical grinding. Donghua UniversityGoogle Scholar
  26. 26.
    Pramanik A, Zhang LC, Arsecularatne JA (2007) An FEM investigation into the behavior of metal matrix composites: tool-particle interaction during orthogonal cutting. Int J Mach Tools Manuf 47:1497–1506CrossRefGoogle Scholar
  27. 27.
    Fathipour M, Hamedi M, Yousefi R (2013) Numerical and experimental analysis of machining of Al (20 vol% SiC) composite by the use of ABAQUS software. Mater Werkst 44:14–20CrossRefGoogle Scholar
  28. 28.
    Deng JH, Zhang B (2002) Material removal mechanism in ceramic grinding. China Mech Eng 18:84–87Google Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2019

Authors and Affiliations

  • Daohui Xiang
    • 1
    Email author
  • Zhanli Shi
    • 1
  • Haoren Feng
    • 1
  • Bangfu Wu
    • 1
  • Zhimeng Zhang
    • 1
  • Yanbin Chen
    • 1
  • Xiaoxiao Niu
    • 1
  • Bo Zhao
    • 1
  1. 1.School of Mechanical and Power EngineeringHenan Polytechnic UniversityJiaozuoChina

Personalised recommendations