Advertisement

The effect of PSD on properties of unimodal and bimodal powders using 17-4 PH stainless steel powder

  • N. S. Muchavi
  • M. Seerane
  • R. MachakaEmail author
ORIGINAL ARTICLE
  • 62 Downloads

Abstract

17-4 PH is a martensitic precipitation-hardening stainless steel that possesses an outstanding combination of superior physical and mechanical properties, good toughness, resistance to corrosion, and is easily machinable and weldable. It is widely used in the chemical, petrochemical, and aerospace industries. In this paper, we study the effect of the particle size distribution of unimodal and bimodal powders on properties of 17-4 PH stainless steel parts manufactured through metal injection molding (MIM). Unimodal and bimodal injectable MIM feedstocks of 60 vol% solids loading were prepared using powders of three different particle sizes with a wax-based binder system. The results show that coarser particle sizes (unimodal or bimodal) exhibit relatively lower shrinkage levels which is desirable for dimensional control but inferior “as-sintered” mechanical properties. The finer particle sizes (unimodal or bimodal) exhibited inferior rheological feedstock properties but comparatively superior “as-sintered” mechanical properties. The study suggests that bimodal feedstocks of finer particle sizes exhibit a favorable combination of rheological properties and “as-sintered” mechanical properties.

Keywords

Metal injection molding Particle size 17-4 PH stainless steel Bimodal feedstocks Mechanical properties 

Notes

Acknowledgments

Epson Atmix Corporation in Japan is thanked for the supply of the powders used in this study. The contributions of Ntate Sam Papo, Lusanda Fikeni, Ntswaki Nyakane, Filipe Pereira, Chris McDuling, and Pierre Rossouw are duly recognized. We are also truly indebted to Phumlani Ndlangamandla, who collected some of the results as an undergraduate student from the University of Pretoria so as to his supervisor Vinod Kurup.

Author contributions

Study conception and design: Ronald Machaka (RM) and Phumlani Ndlangamandla (PN); Acquisition and processing of experimental data: Noluntu S. Muchavi (NSM), PN, RM, Mandy Seerane (MS), Lusanda Fikeni (LF), and Ntswaki Nyakane (NN); Analysis and interpretation of data: NSM, MS, and RM; Drafting of the manuscript: NSM, MS, and RM; Critical revision: NSM, MS, and RM; Final approval: NSM, MS, and RM; Lead and guarantor author: RM

Funding information

The CSIR supported this work through a Parliamentary Grant and the Department of Science and Innovation also supported this work through the Advanced Material initiative.

References

  1. 1.
    Gülsoy HÖ, Özbek S, Baykara T (2007) Microstructural and mechanical properties of injection moulded gas and water atomised 17-4 PH stainless steel powder. Powder Metall 50:120–126.  https://doi.org/10.1179/174329007X153288 CrossRefGoogle Scholar
  2. 2.
    Murr LE, Gaytan SM, Ramirez DA, Martinez E, Hernandez J, Amato KN, Shindo PW, Medina FR, Wicker RB (2012) Metal fabrication by additive manufacturing using laser and electron beam melting technologies. J Mater Sci Technol 28:1–14.  https://doi.org/10.1016/S1005-0302(12)60016-4 CrossRefGoogle Scholar
  3. 3.
    Kumar VA, Gupta RK, Karthikeyan MK, Prasad KN, Sinha PP, Rao MN, 2007 Processing and characterization of thin sheets of 17-4PH stainless steel for aerospace application, in: Int Conf Adv Mater ComposGoogle Scholar
  4. 4.
    Neilan A, Warzel III R, Hu B, Neyman R, Hinchliffe J, (2017) Characterization of martensitic stainless steels in PM components, in: Int. Conf. Powder Metall. Part. Mater. (POWDERMET 2017), Metal Powder Industries Federation (MPIF), Las Vegas, USAGoogle Scholar
  5. 5.
    Murr LE, Martinez E, Hernandez J, Collins S, Amato KN, Gaytan SM, Shindo PW (2012) Microstructures and properties of 17-4 PH stainless steel fabricated by selective laser melting. J Mater Res Technol 1:167–177.  https://doi.org/10.1016/S2238-7854(12)70029-7 CrossRefGoogle Scholar
  6. 6.
    Reinshagen JH, Witsberger JC (1994) Properties of precipitation hardening stainless steel processed by conventional powder metallurgy techniques. Adv Powder Metall Part Mater 7:313–323Google Scholar
  7. 7.
    DebRoy T, Wei HL, Zuback JS, Mukherjee T, Elmer JW, Milewski JO, Beese AM, Wilson-Heid A, De A, Zhang W (2018) Additive manufacturing of metallic components – process, structure and properties. Prog Mater Sci 92:112–224.  https://doi.org/10.1016/j.pmatsci.2017.10.001 CrossRefGoogle Scholar
  8. 8.
    Wu M-W, Huang Z-K, Tseng C-F, Hwang K-S (2015) Microstructures, mechanical properties, and fracture behaviors of metal-injection molded 17-4PH stainless steel. Met Mater Int 21:531–537.  https://doi.org/10.1007/s12540-015-4369-y CrossRefGoogle Scholar
  9. 9.
    Ferri OM, Ebel T, Bormann R (2010) Influence of surface quality and porosity on fatigue behaviour of Ti–6Al–4V components processed by MIM. Mater Sci Eng A 527:1800–1805.  https://doi.org/10.1016/j.msea.2009.11.007 CrossRefGoogle Scholar
  10. 10.
    Barriere T, Liu B, Gelin JC (2003) Determination of the optimal process parameters in metal injection molding from experiments and numerical modeling. J Mater Process Technol 143–144:636–644.  https://doi.org/10.1016/S0924-0136(03)00473-4 CrossRefGoogle Scholar
  11. 11.
    Pachauri P, Hamiuddin M (2015) Optimization of injection moulding process parameters in MIM for impact toughness of sintered parts. Cloud Publ Int J Adv Mater Metall Eng 1:1–11Google Scholar
  12. 12.
    Seerane M, Ndlangamandla P, Machaka R (2016) The influence of particle size distribution on the properties of metal- injection-moulded 17-4 PH stainless steel. J South Afr Inst Min Metall 116:1–6CrossRefGoogle Scholar
  13. 13.
    Chen X, (1998) Particle packing, compaction and sintering in powder metallurgy, University of AlbertaGoogle Scholar
  14. 14.
    Sotomayor ME, Várez A, Levenfeld B (2010) Influence of powder particle size distribution on rheological properties of 316L powder injection moulding feedstocks. Powder Technol 200:30–36.  https://doi.org/10.1016/j.powtec.2010.02.003 CrossRefGoogle Scholar
  15. 15.
    Amin SYM, Jamaludin KR, Muhamad N, (2008) Rheological properties of SS316L MIM feedstock prepared with different particle sizes and powder loadings, 59–63Google Scholar
  16. 16.
    Li Y, Li L, Khalil KA (2007) Effect of powder loading on metal injection molding stainless steels. J Mater Process Technol 183:432–439.  https://doi.org/10.1016/j.jmatprotec.2006.10.039 CrossRefGoogle Scholar
  17. 17.
    Zheng J, Carlson WB, Reed JS (1995) The packing density of binary powder mixtures. J Eur Ceram Soc 15:479–483.  https://doi.org/10.1016/0955-2219(95)00001-B CrossRefGoogle Scholar
  18. 18.
    German RM (1992) Prediction of sintered density for bimodal powder mixtures prediction of sintered density for bimodal powder mixtures. Metall Mater Trans A 23A:1455–1465.  https://doi.org/10.1007/BF02647329 CrossRefGoogle Scholar
  19. 19.
    Desmond KW, Weeks ER (2013) Influence of particle size distribution on random close packing of spheres. Phys Rev E 90:1–6Google Scholar
  20. 20.
    Aggarwal G, Park SJ, Smid I (2006) Development of niobium powder injection molding: Part I. Feedstock and injection molding. Int J Refract Met Hard Mater 24:253–262.  https://doi.org/10.1016/j.ijrmhm.2005.06.003 CrossRefGoogle Scholar
  21. 21.
    Hidalgo J, Jiménez-Morales A, Torralba JM (2012) Torque rheology of zircon feedstocks for powder injection moulding. J Eur Ceram Soc 32:4063–4072.  https://doi.org/10.1016/j.jeurceramsoc.2012.06.023 CrossRefGoogle Scholar
  22. 22.
    Amin A, Sri Yulis M, Muhamad N, Jamaludin KR, Abdullah S, Batu Pahat, P. (2007) Process, Rheological investigation of MIM feedstocks prepared with different particle sizes, in: World Eng Congr, Penang, Malaysia, 2007:212–218Google Scholar
  23. 23.
    Zakaria H, Muhamad N, Sulong AB, Irwan Ibrahim MH, Foudzi F (2014) Moldability characteristics of 3 mol% yttria stabilized zirconia feedstock for micro-powder injection molding process. Sains Malaysiana 43:129–136Google Scholar
  24. 24.
    Agote I, Odriozola A, Gutierrez M, Santamaría A, Quintanilla J, Coupelle P, Soares J (2001) Rheological study of waste porcelain feedstocks for injection moulding. J Eur Ceram Soc 21:2843–2853.  https://doi.org/10.1016/S0955-2219(01)00210-2 CrossRefGoogle Scholar
  25. 25.
    Mohammad S, Ghasemi E, Alizadeh M, Yazdani R (2014) Processing research rheological properties of Mg based feedstocks with micro or nano Al2O3 powder for injection molding. J Ceram Process Res 15:236–241Google Scholar
  26. 26.
    Weir FE (1963) Moldability of plastics based on melt rheology. Part 1 - theoretical development. Polym Eng Sci 3:32–36.  https://doi.org/10.1002/pen.760030108 CrossRefGoogle Scholar
  27. 27.
    Machaka R, Ndlangamandla P, Seerane M (2018) Capillary rheological studies of 17-4 PH MIM feedstocks prepared using a custom CSIR binder system. Powder Technol 326:37–43.  https://doi.org/10.1016/j.powtec.2017.12.051 CrossRefGoogle Scholar
  28. 28.
    Oh JW, Lee WS, Park SJ (2018) Investigation and modeling of binder removal process in nano/micro bimodal powder injection molding. Int J Adv Manuf Technol 97:4115–4126.  https://doi.org/10.1007/s00170-018-2263-8 CrossRefGoogle Scholar
  29. 29.
    Machaka R, Seerane M, Chikwanda HK, (2014) Binder development for metal injection moulding : a CSIR perspectiveGoogle Scholar
  30. 30.
    ASTM (2008) ASTM B962 - 08 Standard test methods for density of compacted or sintered powder metallurgy (PM) products using Archimedes’ principle, ASTM B962 - 08 Stand. test methods density compact. or sintered powder Metall Prod Using Arch PrincGoogle Scholar
  31. 31.
    Spierings AB, Schneider M, Eggenberger R (2011) Comparison of density measurement techniques for additive manufactured metallic parts. Rapid Prototyp J 17:380–386.  https://doi.org/10.1108/13552541111156504 CrossRefGoogle Scholar
  32. 32.
    Dihoru LV, Smith LN, Orban R, German RM (2000) Experimental study and neural network modeling of the stability of powder injection molding feedstocks. Mater Manuf Process 15:419–438CrossRefGoogle Scholar
  33. 33.
    Suri P, Atre SV, German RM, de Souza JP (2003) Effect of mixing on the rheology and particle characteristics of tungsten-based powder injection molding feedstock. Mater Sci Eng A 356:337–344.  https://doi.org/10.1016/S0921-5093(03)00146-1 CrossRefGoogle Scholar
  34. 34.
    Khakbiz M, Simchi A, Bagheri R (2005) Analysis of the rheological behavior and stability of 316L stainless steel–TiC powder injection molding feedstock. Mater Sci Eng A 407:105–113.  https://doi.org/10.1016/j.msea.2005.06.057 CrossRefGoogle Scholar
  35. 35.
    Tatt TK, Muhamad N, Muchtar A, Sulong AB, Yunn HS (2012) Rheological behaviour of novel feedstock for manufacturing porous stainless steel via (MIM)-PSH. J Teknol (Sciences Eng) 59:187–191Google Scholar
  36. 36.
    Jamaludin KR, Muhamad N, Mohd MN, Ahmad S, Ibrahim MHI, Nor NHM (2009) Optimizing the injection parameter of water atomised SS316l powder with design of experiment method for best sintered density. Chiang Mai J Sci 36:349–358Google Scholar
  37. 37.
    Mohamad Nor N, Muhamad N, Ismail M, Jamaludin K, Ahmad S, Ibrahim M (2009) Flow behaviour to determine the defects of green part in metal injection molding. Int J Mech Mater Eng 4:70–75Google Scholar
  38. 38.
    German RM, Bose A (1997) Injection molding of metals and ceramics, 2nd edn. Metal Powder Industries Federation (Princeton, N.J., U.S.A), PrincetonGoogle Scholar
  39. 39.
    Bose A, Otsuka I, Yoshida T, Toyoshima H (2008) Faster sintering and lower costs with ultra-fine MIM powders. Met Powder Rep 63:25–30.  https://doi.org/10.1016/S0026-0657(08)70058-4 CrossRefGoogle Scholar
  40. 40.
    Kearns M, Murray K, Tingskog T (2009) Effects of particle size and alloy chemistry on processing and properties of MIM powders BT - 2009 International Conference on Powder Metallurgy and Particulate Materials. PowderMet 2009:41–48Google Scholar
  41. 41.
    Todd I, Sidambe AT, 2013 Developments in metal injection moulding (MIM), in: Chang I, Zhao Y (Eds.), Adv Powder Metall Prop Process Appl, Woodhead Publishing, Sheffield, pp. 109–146.  https://doi.org/10.1533/9780857098900.1.109 CrossRefGoogle Scholar
  42. 42.
    Muchavi NS, Bam L, de Beer FC, Chikosha S, Machaka R (2016) X-ray computed microtomography studies of MIM and DPR parts. J South Afr Inst Min Metall 116:973–980.  https://doi.org/10.17159/2411-9717/2016/v116n10a13 CrossRefGoogle Scholar
  43. 43.
    Suri P, Smarslok BP, German RM (2006) Impact properties of sintered and wrought 17–4 PH stainless steel. Powder Metall 49:40–47CrossRefGoogle Scholar
  44. 44.
    Shi J, Cheng Z, Gelin JC, Barriere T, Liu B (2017) Sintering of 17-4PH stainless steel powder assisted by microwave and the gradient of mechanical properties in the sintered body. Int J Adv Manuf Technol 91:2895–2906.  https://doi.org/10.1007/s00170-016-9960-y CrossRefGoogle Scholar
  45. 45.
    Attia UM, Alcock JR (2011) A review of micro-powder injection moulding as a microfabrication technique. J Micromech Microeng 21:043001.  https://doi.org/10.1088/0960-1317/21/4/043001 CrossRefGoogle Scholar
  46. 46.
    Murray K, Coleman AJ, Tingskog TA, Whychell DT Sr (2011) Effect of particle size distribution on processing and properties of MIM 17-4PH. Int J Powder Metall 47:21–28Google Scholar
  47. 47.
    Tang M, Pistorius PC (2017) Oxides , porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting. Int J Fatigue 94:192–201.  https://doi.org/10.1016/j.ijfatigue.2016.06.002 CrossRefGoogle Scholar
  48. 48.
    Fotovvati B, Namdari N, Dehghanghadikolaei A, (2019) Fatigue performance of selective laser melted Ti6Al4V components : state of the art, Mater Res Express 6CrossRefGoogle Scholar
  49. 49.
    German RM (2018) MIM 17-4 PH stainless steel: processing, properties and best practice. Powder Inject Mould Int 12:49–76Google Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2019

Authors and Affiliations

  1. 1.Advanced Manufacturing & Engineering, Manufacturing ClusterCouncil for Scientific and Industrial ResearchPretoriaSouth Africa
  2. 2.Department of Metallurgy, School of Mining, Metallurgy and Chemical EngineeringUniversity of JohannesburgPretoriaSouth Africa

Personalised recommendations