Advertisement

Heat transfer modeling of dissimilar FSW of Al 6061/AZ31 using experimentally measured thermo-physical properties

  • Amit Kumar Singh
  • Pankaj Sahlot
  • Manas Paliwal
  • Amit AroraEmail author
ORIGINAL ARTICLE
  • 4 Downloads

Abstract

A heat transfer numerical model is developed for friction stir welding of dissimilar materials Al 6061 and AZ31 alloy. Thermo-physical properties were experimentally determined for the stir zone and compared with the base alloys. Experimentally determined thermo-physical properties of the stir zone are not strictly the average values of the base alloys but exhibit a complex relationship with the microstructural features and the intermixing of Al and Mg in the weld region. The numerical model is employed to predict the temperature distribution on the advancing and retreating side. A good agreement between computed and experimentally measured results was obtained at 24-mm, 20-mm, and 16-mm tool shoulder diameter. The proposed model can be used to predict the thermal cycle, peak temperature, and thermo-mechanically affected zone for welding of dissimilar materials on friction stir welding.

Keywords

Dissimilar weld Friction stir welding Intermixing Numerical modeling Thermo-physical properties 

Notes

Acknowledgments

The authors would like to thank Prof. Satish Vitta, Metallurgical Engineering and Materials Science IIT Bombay, for his help with thermal diffusivity measurement. The authors would also like to acknowledge Mr. Aroh Shrivastava, Institute for Plasma Research, for his help in specific heat capacity measurement.

Funding information

This study was funded by the Board of Research in Nuclear Sciences (BRNS) (project number 57/14/05/2019-BRNS) and Science and Engineering Research Board (SERB) (project number CRG/2018/004944).

References

  1. 1.
    Mordike BL, Ebert T (2001) Magnesium properties - applications - potential. Mater Sci Eng A 302(1):37–45  https://doi.org/10.1016/S0921-5093(00)01351-4
  2. 2.
    Thomas WM, Nicholas ED, Needham JC, Murch MG, Temple- Smith P, Dawes CJ (1991) Friction Stir Butt Welding, International Patent Application No. PCT/GB92/02203, and US Patent No. 5, 460 (1995) 317 https://patents.google.com/patent/WO1993010935A1/
  3. 3.
    Park SHC, Sato YS, Kokawa H (2003) Effect of micro-texture on fracture location in friction stir weld of Mg alloy AZ61 during tensile test. Scr Mater 49(2):161–166.  https://doi.org/10.1016/S1359-6462(03)00210-0 CrossRefGoogle Scholar
  4. 4.
    Mishra RS, Ma ZY (2005) Friction stir welding and processing. Mater Sci Eng R Rep 50(1–2):1–78.  https://doi.org/10.1016/j.mser.2005.07.001 CrossRefGoogle Scholar
  5. 5.
    Nandan R, DebRoy T, Bhadeshia HKDH (2008) Recent advances in friction stir welding – process, weldment structure and properties. Prog Mater Sci 53(6):980–1023.  https://doi.org/10.1016/j.pmatsci.2008.05.001 CrossRefGoogle Scholar
  6. 6.
    Shah LH, Othman NH, Gerlich A (2018) Review of research progress on aluminium–magnesium dissimilar friction stir welding. Sci Technol Weld Join 23(3):256–270.  https://doi.org/10.1080/13621718.2017.1370193 CrossRefGoogle Scholar
  7. 7.
    Nandan R, Roy GG, DebRoy T (2006) Numerical simulation of three-dimensional heat transfer and plastic flow during friction stir welding. Metall Mater Trans A 37(4):1247–1259.  https://doi.org/10.1007/s11661-006-1076-9 CrossRefGoogle Scholar
  8. 8.
    Nandan R, Prabu B, De A, DebRoy T (2007) Improving reliability of heat transfer and materials flow calculations during friction stir welding of dissimilar aluminum alloys. Weld Res 86:313–322Google Scholar
  9. 9.
    Jamshidi Aval H, Serajzadeh S, Kokabi AH (2012) Experimental and theoretical evaluations of thermal histories and residual stresses in dissimilar friction stir welding of AA5086-AA6061. Int J Adv Manuf Technol 61(1–4):149–160.  https://doi.org/10.1007/s00170-011-3713-8 CrossRefGoogle Scholar
  10. 10.
    Shojaeefard MH, Behnagh RA, Akbari M, Givi MKB, Farhani F (2013) Modelling and pareto optimization of mechanical properties of friction stir welded AA7075/AA5083 butt joints using neural network and particle swarm algorithm. Mater Des 44:190–198.  https://doi.org/10.1016/j.matdes.2012.07.025 CrossRefGoogle Scholar
  11. 11.
    Jonckheere C, De Meester B, Denquin A, Simar A (2013) Torque, temperature and hardening precipitation evolution in dissimilar friction stir welds between 6061-T6 and 2014-T6 aluminum alloys. J Mater Process Technol 213(6):826–837.  https://doi.org/10.1016/j.jmatprotec.2013.01.001 CrossRefGoogle Scholar
  12. 12.
    Padmanaban R, Ratna Kishore V, Balusamy V (2014) Numerical simulation of temperature distribution and material flow during friction stir welding of dissimilar aluminum alloys. Procedia Eng 97:854–863.  https://doi.org/10.1016/j.proeng.2014.12.360 CrossRefGoogle Scholar
  13. 13.
    Guo JF, Chen HC, Sun CN, Bi G, Sun Z, Wei J (2014) Friction stir welding of dissimilar materials between AA6061 and AA7075 Al alloys effects of process parameters. Mater Des 56:185–192.  https://doi.org/10.1016/j.matdes.2013.10.082 CrossRefGoogle Scholar
  14. 14.
    Ratna Kishore V, Arun J, Padmanabhan R, Balasubramanian V (2015) Parametric studies of dissimilar friction stir welding using computational fluid dynamics simulation. Int J Adv Manuf Technol 80(1–4):91–98.  https://doi.org/10.1007/s00170-015-6995-4 CrossRefGoogle Scholar
  15. 15.
    Al-Badour F, Merah N, Shuaib A, Bazoune A (2014) Thermo-mechanical finite element model of friction stir welding of dissimilar alloys. Int J Adv Manuf Technol 72(5–8):607–617.  https://doi.org/10.1007/s00170-014-5680-3 CrossRefGoogle Scholar
  16. 16.
    Tang J, Shen Y (2016) Numerical simulation and experimental investigation of friction stir lap welding between aluminum alloys AA2024 and AA7075. J Alloys Compd 666:493–500.  https://doi.org/10.1016/j.jallcom.2016.01.138 CrossRefGoogle Scholar
  17. 17.
    Yang CL, Wu CS, Lv XQ (2018) Numerical analysis of mass transfer and material mixing in friction stir welding of aluminum/magnesium alloys. J Manuf Process 32:380–394.  https://doi.org/10.1016/j.jmapro.2018.03.009 CrossRefGoogle Scholar
  18. 18.
    Mohammadi J, Behnamian Y, Mostafaei A, Gerlich AP (2015) Tool geometry, rotation and travel speeds effects on the properties of dissimilar magnesium/aluminum friction stir welded lap joints. Mater Des 75:95–112.  https://doi.org/10.1016/j.matdes.2015.03.017 CrossRefGoogle Scholar
  19. 19.
    Malarvizhi S, Balasubramanian V (2012) Influences of tool shoulder diameter to plate thickness ratio (D/T) on stir zone formation and tensile properties of friction stir welded dissimilar joints of AA6061 aluminum-AZ31B magnesium alloys. Mater Des 40:453–460.  https://doi.org/10.1016/j.matdes.2012.04.008 CrossRefGoogle Scholar
  20. 20.
    Soundararajan V, Zekovic S, Kovacevic R (2005) Thermo-mechanical model with adaptive boundary conditions for friction stir welding of Al 6061. Int J Mach Tools Manuf 45(14):1577–1587.  https://doi.org/10.1016/j.ijmachtools.2005.02.008 CrossRefGoogle Scholar
  21. 21.
    Arora A, Nandan R, Reynolds AP, DebRoy T (2009) Torque, power requirement and stir zone geometry in friction stir welding through modeling and experiments. Scr Mater 60(1):13–16.  https://doi.org/10.1016/j.scriptamat.2008.08.015 CrossRefGoogle Scholar
  22. 22.
    Hanitzsch E (1991) Modification of the conventional measuring method to determine the specific heat capacity using a Perkin-Elmer DSC 2. Thermochim Acta 187:275–281.  https://doi.org/10.1016/0040-6031(91)87204-A CrossRefGoogle Scholar
  23. 23.
    Nandan R, Lienert TJ, DebRoy T (2008) Toward reliable calculations of heat and plastic flow during friction stir welding of Ti-6Al-4V alloy. Int J Mater Res 99(4):434–444.  https://doi.org/10.3139/146.101655 CrossRefGoogle Scholar
  24. 24.
    Nandan R, Roy GG, Lienert TJ, DebRoy T (2006) Numerical modelling of 3D plastic flow and heat transfer during friction stir welding of stainless steel. Sci Technol Weld Join 11(5):526–537.  https://doi.org/10.1179/174329306X107692 CrossRefGoogle Scholar
  25. 25.
    Cai W, Daehn G, Vivek A, Li J, Khan H, Mishra R, Komarasamy M (2018) A state-of-the-art review on solid-state metal joining. J Manuf Sci Eng C 2018.  https://doi.org/10.1115/MSEC2018-6683
  26. 26.
    Lee S, Ham HJ, Kwon SY, Kim SW, Suh CM (2013) Thermal conductivity of magnesium alloys in the temperature range from -125 C to 400 0C. Int J Thermophys 34(12):2343–2350.  https://doi.org/10.1007/s10765-011-1145-1 CrossRefGoogle Scholar
  27. 27.
    Ulysse P (2002) Three-dimensional modeling of the friction stir-welding process. Int J Mach Tools Manuf 42(14):1549–1557.  https://doi.org/10.1016/S0890-6955(02)00114-1 CrossRefGoogle Scholar
  28. 28.
    Pan H, Pan F, Wang X, Peng J, Gou J, She J, Tang A (2013) Correlation on the electrical and thermal conductivity for binary Mg-Al and Mg-Zn alloys. Int J Thermophys 34(7):1336–1346.  https://doi.org/10.1007/s10765-013-1490-3 CrossRefGoogle Scholar
  29. 29.
    Huang K, Logé RE (2016) A review of dynamic recrystallization phenomena in metallic materials. Mater Des 111:548–574.  https://doi.org/10.1016/j.matdes.2016.09.012 CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2019

Authors and Affiliations

  • Amit Kumar Singh
    • 1
  • Pankaj Sahlot
    • 1
    • 2
  • Manas Paliwal
    • 1
  • Amit Arora
    • 1
    Email author
  1. 1.Materials Science and EngineeringIndian Institute of Technology GandhinagarGandhinagarIndia
  2. 2.Mechanical Engineering, School of TechnologyPandit Deendayal Petroleum UniversityGandhinagarIndia

Personalised recommendations