Advertisement

An experimental study on the effect of high-pressure coolant on chip fragmentation during the turning of stainless steel

  • Vincent WagnerEmail author
  • Jean-Pierre Faye
  • Gilles Dessein
ORIGINAL ARTICLE
  • 52 Downloads

Abstract

The high-pressure coolant is considered as a very important point to improve the machining performance. Most of the papers concern the effect of high-pressure coolant on titanium where its efficiency is very important. This paper investigates the application of a high-pressure lubricant during the turning of stainless steel using coated carbide tools to control the chip size through an extensive experimental work. The effects of the cutting conditions, the cutting tool geometries, and the lubricant pressure were studied. A model was developed to clearly understand the mechanical effects of a lubricant on the chip fragmentation. This model is partially based on a Maln experimental analysis in which a high-speed camera was used to define the jet geometry. Finally, the relationship between the cutting conditions and the pressure is meticulously described.

Keywords

Cutting Stainless steel High-pressure coolant Chip formation 

Notes

References

  1. 1.
    Ayed Y, Germain G, Ammar A, Furet B (2013) Degradation modes and tool wear mechanisms in finish and rough machining of ti17 titanium alloy under high-pressure water jet assistance. Wear 305(1):228–237CrossRefGoogle Scholar
  2. 2.
    Ayed Y, Robert C, Germain G, Ammar A (2016) Development of a numerical model for the understanding of the chip formation in high-pressure water-jet assisted machining. Finite Elem Anal Des 108:1–8CrossRefGoogle Scholar
  3. 3.
    Barelli F, Wagner V, Laheurte R, Dessein G, Darnis P, Cahuc O, Mousseigne M (2016) Orthogonal cutting of ta6v alloys with chamfered tools: analysis of tool–chip contact lengths. In: Proceedings of the Institution of Mechanical Engineers, Part b: Journal of Engineering Manufacture p 0954405416629589Google Scholar
  4. 4.
    Braham-Bouchnak T, Germain G, Morel A, Furet B (2015) Influence of high-pressure coolant assistance on the machinability of the titanium alloy ti555–3. Mach Sci Technol 19(1):134–151CrossRefGoogle Scholar
  5. 5.
    Courbon C, Kramar D, Krajnik P, Pusavec F, Rech J, Kopac J (2009) Investigation of machining performance in high-pressure jet assisted turning of inconel 718: an experimental study. Int J Mach Tools Manuf 49 (14):1114–1125CrossRefGoogle Scholar
  6. 6.
    Courbon C, Sajn V, Kramar D, Rech J, Kosel F, Kopac J (2011) Investigation of machining performance in high pressure jet assisted turning of inconel 718: a numerical model. J Mater Process Technol 211 (11):1834–1851CrossRefGoogle Scholar
  7. 7.
    Dahlman P, Escursell M (2004) High-pressure jet-assisted cooling: a new possibility for near net shape turning of decarburized steel. Int J Mach Tools Manuf 44(1):109–115CrossRefGoogle Scholar
  8. 8.
    Jawahir I, Van Luttervelt C (1993) Recent developments in chip control research and applications. CIRP Ann Manuf Technol 42(2):659–693CrossRefGoogle Scholar
  9. 9.
    Kaynak Y, Gharibi A, Ylmaz U, Köklü U, Aslantaş K (2018) A comparison of flood cooling, minimum quantity lubrication and high pressure coolant on machining and surface integrity of titanium Ti-5553 alloy. J Manuf Process 34:503–512CrossRefGoogle Scholar
  10. 10.
    Klocke F, Lung D, Cayli T, Döbbeler B, Sangermann H (2014) Evaluation of energy efficiency in cutting aerospace materials with high-pressure cooling lubricant supply. Int J Precis Eng Manuf 15(6):1179–1185CrossRefGoogle Scholar
  11. 11.
    Komanduri R, Von Turkovich B (1981) New observations on the mechanism of chip formation when machining titanium alloys. Wear 69(2):179–188CrossRefGoogle Scholar
  12. 12.
    Molinari A, Musquar C, Sutter G (2002) Adiabatic shear banding in high speed machining of ti–6al–4v: experiments and modeling. Int J Plast 18(4):443–459CrossRefGoogle Scholar
  13. 13.
    Nandy A, Paul S (2008) Effect of coolant pressure, nozzle diameter, impingement angle and spot distance in high pressure cooling with neat oil in turning ti-6al-4v. Mach Sci Technol 12(4):445–473CrossRefGoogle Scholar
  14. 14.
    Naves V, Da Silva M, Da Silva F (2013) Evaluation of the effect of application of cutting fluid at high pressure on tool wear during turning operation of aisi 316 austenitic stainless steel. Wear 302(1):1201–1208CrossRefGoogle Scholar
  15. 15.
    Wagner V, Baili M, Dessein G (2015) The relationship between the cutting speed, tool wear, and chip formation during ti-5553 dry cutting. Int J Adv Manuf Technol 76(5-8):893–912CrossRefGoogle Scholar
  16. 16.
    Wagner V, Dessein G, Gendron J Evolution of chip morphology during high strength stainless steel turning. Major topics of the full argumentations are the following, p 481Google Scholar
  17. 17.
    Wagner V, Vissio A, Duc E, Pijolat M (2016) Relationship between cutting conditions and chips morphology during milling of aluminium al-2050. Int J Adv Manuf Technol 82(9-12):1881–1897CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2019

Authors and Affiliations

  1. 1.Laboratoire Génie de Production LGPUniversité de Toulouse, INP-ENITTarbesFrance

Personalised recommendations