Advertisement

Development of a symmetrical four-roller bending process

  • Gaochao YuEmail author
  • Jun Zhao
  • Changfu Xu
ORIGINAL ARTICLE
  • 29 Downloads

Abstract

In order to reduce the straight edge section and simplify process flow, a new symmetrical four-roller bending process is proposed, and its optimum forming process is determined. The main procedure composes of feeding, pre-bending, reverse roll bending, final bending, positive roll bending, unloading, and springback. It has advantages of less production procedure, small remaining straight edge, and simple equipment structure. Three methods are adopted to study the process, i.e., theoretical analysis, numerical simulation, and physical experiment. According to the theory of elastoplastic and geometric relation, the relationship between the reduction of the upper roller and the curvature radius before and after springback is established, and the reduction of the upper roller can be predicted. The symmetrical four-roller bending process is simulated by ABAQUS software. The distribution of stress and strain is analyzed, and the theoretical curvature radius and the simulated curvature radius are compared. The rolling part is obtained from simulation with an ovality of 0.43% and only 1.5 times the thickness of the remaining straight edge. The symmetrical four-roller bending machine is designed, and the ovality of the rolling part from experiment is less than 5%, and the minimum is only 1.74%. The error of most curvature radius is less than 0.5%. Numerical simulation and physical experiments both prove the feasibility of the method. The effect of the process parameters on the curvature after springback is studied by a single variable method. This process provides a new idea for pipe production and helps improve the rolling quality.

Keywords

Thin-walled pipe Four-roller bending Four-point bending Springback Numerical simulation Process parameters 

Notes

Funding information

This project was funded and supported by the Project funded by China Postdoctoral Science Foundation (2018M641672), Science and Technology Project of Qinhuangdao (201805A007), National Natural Science Foundation of China (51575473), and Doctoral Foundation of Yanshan University (BL18024).

References

  1. 1.
    Gandhi AH, Gajjar HV, Raval HK (2008) Mathematical modelling and finite element simulation of pre-bending stage of three-roller plate bending process. Proc ASME Int Manuf Sci Eng Conf 1:617–625Google Scholar
  2. 2.
    Zhang ZQ, Song JL, Fu JH, Li YT, Guo YN (2014) A refined model of three-roller elastoplastic asymmetrical pre-bending of plate. J Iron Steel Res Int 21:328–334CrossRefGoogle Scholar
  3. 3.
    Hu W, Wang ZR (2001) Theoretical analysis and experimental study to support the development of a more valuable roll-bending process. Int J Mach Tool Manu 41(5):731–747CrossRefGoogle Scholar
  4. 4.
    Gandhi AH, Raval HK (2008) Analytical and empirical modeling of top roller position for three-roller cylindrical bending of plates and its experimental verification. J Mater Process Technol 197:268–278CrossRefGoogle Scholar
  5. 5.
    Fu Z, Tian X, Chen W, Hu B, Yao X (2013) Analytical modeling and numerical simulation for three-roll bending forming of sheet metal. Int J Adv Manuf Technol 69:1639–1647CrossRefGoogle Scholar
  6. 6.
    Zeng J, Liu Z, Champliaud H (2008) FEM dynamic simulation and analysis of the roll-bending process for forming a conical tube. J Mater Process Technol 198:330–343CrossRefGoogle Scholar
  7. 7.
    Ktari A, Antar Z, Haddar N (2012) Modeling and computation of the three-roller bending process of steel sheets. J Mech Sci Technol 26(1):123–128CrossRefGoogle Scholar
  8. 8.
    Quan TH, Champliaud H, Feng ZK, Salem J, My DT (2013) Heat-assisted roll-bending process dynamic simulation. Int J Model Simul 33(1):54–62Google Scholar
  9. 9.
    Chudasama MK, Raval HK (2014) Bending force prediction for dynamic roll-bending during 3-roller conical bending process. J Manuf Process 16:284–295CrossRefGoogle Scholar
  10. 10.
    Feng ZK, Champliaud H, Dao TM (2009) Numerical study of non-kinematical conical bending with cylindrical rolls. Simul Model Pract Theory 17:1710–1722CrossRefGoogle Scholar
  11. 11.
    Salem J, Champliaud H, Feng ZK, Dao TM (2016) Experimental analysis of an asymmetrical three-roll bending process. Int J Adv Manuf Technol 83(9):1823–1833CrossRefGoogle Scholar
  12. 12.
    Yu GC, Zhao J, Zhao FP (2017) Elastic-plastic secondary indeterminate problem for thin-walled pipe through the inner-wall loading by three-point bending. Mech Based Des Struct 45:219–238CrossRefGoogle Scholar
  13. 13.
    Yu GC, Zhao J, Zhai RX, Ma R, Wang CG (2018) Theoretical analysis and experimental investigations on the symmetrical three-roller setting round process. Int J Adv Manuf Technol 94:45–56CrossRefGoogle Scholar
  14. 14.
    Hua M, Baines K, Cole IM (1995) Bending mechanisms, experimental techniques and preliminary tests for the continuous four-roll plate bending process. J Mater Process Technol 48(1):159–172CrossRefGoogle Scholar
  15. 15.
    Hua M, Lin YH (1999) Large deflection analysis of elastoplastic plate in steady continuous four-roll bending process. Int J Mech Sci 41(12):1461–1483CrossRefGoogle Scholar
  16. 16.
    Gu X, Franzke M, Bambach M, Hirt G (2010) Experimental and numerical investigation of grid sheet bending behavior in four-roll bending. CIRP Ann Manuf Technol 59(1):303–306CrossRefGoogle Scholar
  17. 17.
    Gao GY, Yu GC, Zhao J, Zhang ZY (2017) Rolling round process of four-roll and its springback analysis. J Plast Eng 24(1):55–62Google Scholar
  18. 18.
    Wu K, Sun Y, Cao C, Zhou C, Liu Q, Chang X (2017) On simulation analysis of plate forming and deformation compensation technology of the side roll for four-roll plate bending machine. Proc Eng 207:1617–1622CrossRefGoogle Scholar
  19. 19.
    Zhou C, Sun Y, Wu K, Liu QY, Chang X, Sheng YL (2018) Modeling and analysis of process parameters in multi-pass four-roll bending. J Plast Eng 25(03):35–41Google Scholar
  20. 20.
    Yan J, Zuo DW, Wang M (2003) A theoretical analysis on the springback of workpiece during two-axle bending. Acta Armamentarii 03:381–384Google Scholar
  21. 21.
    Yan J, Wang M, Zuo DW (2004) Theoretical analysis and experimental study on two-axle bending with elastic roller for forming non-circular cross-section parts. Chin J Mech Eng 11:169–173CrossRefGoogle Scholar
  22. 22.
    Yu GQ, Lu SH (2005) Study of the influence factors on two-roll bending with elastic medium based on finite element analysis. Mech Sci Tech 10:1187–1190 + 1229Google Scholar
  23. 23.
    Zhu BS (2015) Research on the forming force prediction experiment of two-roller bending machine. Yanshan UniversityGoogle Scholar
  24. 24.
    Gong JP, Li XF, Zuo DW, Kang XJ, Qiu JB (2015) Three-dimensional FEA of manufacturing process of small-diameter split sleeve by two-axle bending. Chin Mech Eng 26(08):1117–1124Google Scholar
  25. 25.
    Li J, Li XF, Chen GY, Zuo DW, Sun YB, Min L, Zhu CF (2017) Experiment and simulation of two-axle bending of 301 stainless steel strip with different hardness values. J Plasticity Eng 24(02):28–32Google Scholar
  26. 26.
    Zhao J, Yu GC, Ma R (2016) A mechanical model of symmetrical three-roller setting round process: the static bending stage. J Mater Process Technol 231:501–512CrossRefGoogle Scholar
  27. 27.
    Zhao J, Yin J, Ma R, Ma LX (2011) Springback equation of small curvature plane bending. Sci China Technol Sci 54(9):2386–2396CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2019

Authors and Affiliations

  1. 1.Key Laboratory of Advanced Forging & Stamping Technology and Science(Yanshan University), Ministry of Education of ChinaQinhuangdaoPeople’s Republic of China
  2. 2.College of Mechanical EngineeringYanshan UniversityQinhuangdaoPeople’s Republic of China

Personalised recommendations