Advertisement

Experimental determination of the viscoelastic parameters of K-BKZ model and the influence of temperature field on the thickness distribution of ABS thermoforming

  • Jemyung Cha
  • Moonjeong Kim
  • Dongguen Park
  • Jeung Sang GoEmail author
Open Access
ORIGINAL ARTICLE
  • 97 Downloads

Abstract

This study investigated an influence of the temperature field on thickness distribution of thermoformed products using complex and high-aspect-ratio mold. The optimum temperature field was obtained to achieve a more uniform thickness distribution in the thermoformed products by using finite element simulation. The material properties of acrylonitrile-butadiene-styrene (ABS) polymer sheet were obtained by two rheological measurement tests. The linear viscoelastic properties, such as the storage modulus and loss modulus, were measured by a small amplitude oscillatory shear (SAOS) test for wide ranges of frequency and temperature. The discrete relaxation time and discrete relaxation modulus were obtained by nonlinear regression. The fitting parameters C1 and C2 for the WLF model were obtained by curve fitting. The nonlinear viscoelastic property, such as stress relaxation modulus, was measured by a step strain test. The damping function and fitting parameter α of Wagner-Demarmels (WD) model were determined by curve fitting. Then, the Kaye–Bernstein-Kearsley-Zapas (K-BKZ) constitutive equation was utilized to the thermoforming simulation in order to investigate the material behavior of the polymer sheet. The numerical results showed that a more uniform thickness distribution could be achieved with the optimum temperature field of the sheet. The thinnest part of the products was improved by more than 30%.

Keywords

Thermoforming Thickness distribution Viscoelastic properties Rheological measurement K-BKZ constitutive equation FE simulation Optimum temperature field 

Notes

Funding information

The authors thank the LG Electronics for financial support and useful information on this work. This work was supported by the Ministry of Science, ICT, and Future Planning of the Republic of Korea (No. 2017R1A2B20006264). This work was supported by a 2-Year Research Grant of Pusan National University.

References

  1. 1.
    Nam GJ, Ahn KH, Lee JW (2000) Three-dimensional simulation of thermoforming process and its comparison with experiments. Polym Eng Sci 40:2232–2240CrossRefGoogle Scholar
  2. 2.
    Nam GJ, Lee JW (2001) Numerical and experimental studies of 3-dimensional thermoforming process. J Reinf Plast Compos 20:1182–1190CrossRefGoogle Scholar
  3. 3.
    Sala G, Cassago D, Di Landro L (2002) A numerical and experimental approach to optimise sheet stamping technologies: polymers thermoforming. Mater Des 23:21–39CrossRefGoogle Scholar
  4. 4.
    Lee JK, Virkler TL, Scott CE (2001) Effects of rheological properties and process parameters on ABS thermoforming. Polym Eng Sci 41:240–261CrossRefGoogle Scholar
  5. 5.
    Lee JK, Virkler TL, Scott CE (2001) Influence of initial sheet temperature on ABS thermoforming. Polym Eng Sci 41:1830–1844CrossRefGoogle Scholar
  6. 6.
    Ayhan Z, Zhang QH (2000) Wall thickness distribution in thermoformed food containers produced by a Benco aseptic packaging machine. Polym Eng Sci 40:1–10CrossRefGoogle Scholar
  7. 7.
    Morales RA, Candal MV, Santana OO, Gordillo A, Salazar R (2014) Effect of the thermoforming process variables on the sheet friction coefficient. Mater Des 53:1097–1103CrossRefGoogle Scholar
  8. 8.
    Erdogan ES, Eksi O (2014) Prediction of wall thickness distribution in simple thermoforming moulds. J Mech Eng 60:195–202CrossRefGoogle Scholar
  9. 9.
    Azdast T, Doniavi A, Rash Ahmadi S, Amiri E (2013) Numerical and experimental analysis of wall thickness variation of a hemispherical PMMA sheet in thermoforming process. Int J Adv Manuf Technol 64:113–122CrossRefGoogle Scholar
  10. 10.
    Wang CH, Nied HF (1999) Temperature optimization for improved thickness control in thermoforming. J Mater Process Manuf Sci 8:113–126CrossRefGoogle Scholar
  11. 11.
    Wang S, Makinouchi A, Tosa T, Kidokoro K, Okamoto M, Kotaka T, Nakagawa T (1999) Numerical simulation of acrylonitrile-butadiene-styrene material’s vacuum forming process. J Mater Process Technol 91:219–225CrossRefGoogle Scholar
  12. 12.
    Lau HC, Bhattacharya SN, Field GJ (2000) Influence of rheological properties on the sagging of polypropylene and ABS sheet for thermoforming applications. Polym Eng Sci 40:1564–1570CrossRefGoogle Scholar
  13. 13.
    Baek HM, Giacomin AJ, Wurz MJ (2014) Sag in commercial thermoforming. AICHE J 60:1529–1535CrossRefGoogle Scholar
  14. 14.
    Aus Der Wiesche S (2004) Industrial thermoforming simulation of automotive fuel tanks. Appl Therm Eng 24:2391–2409CrossRefGoogle Scholar
  15. 15.
    Dong Y, Lin RJT, Bhattacharyya D (2006) Finite element simulation on thermoforming acrylic sheets using dynamic explicit method. Polym Polym Compos 14:307–328Google Scholar
  16. 16.
    Ghobadnam M, Mosaddegh P, Rezaei Rejani M et al (2014) Numerical and experimental analysis of HIPS sheets in thermoforming process. Int J Adv Manuf Technol 76:1079–1089CrossRefGoogle Scholar
  17. 17.
    Leite W, Campos Rubio J, Mata Cabrera F, Carrasco A, Hanafi I (2018) Vacuum thermoforming process: an approach to modeling and optimization using artificial neural networks. Polymers (Basel) 10:143CrossRefGoogle Scholar
  18. 18.
    Kaye A (1962) Non-Newtonian flow in incompressible fluids. Aerosp Eng reports, Tech Univ Delft 1–20Google Scholar
  19. 19.
    Bernstein B, Kearsley EA, Zapas LJ (1963) A study of stress relaxation with finite strain. Trans Soc Rheol 7:391–410CrossRefzbMATHGoogle Scholar
  20. 20.
    Lodge AS (1956) A network theory of flow birefringence and stress in concentrated polymer solutions. Trans Faraday Soc 52:120CrossRefGoogle Scholar
  21. 21.
    Wagner MH (1976) Analysis of time-dependent non-linear stress-growth data for shear and elongational flow of a low-density branched polyethylene melt. Rheol Acta 15:136–142CrossRefGoogle Scholar

Copyright information

© The Author(s) 2019

OpenAccessThis article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.

Authors and Affiliations

  • Jemyung Cha
    • 1
  • Moonjeong Kim
    • 1
  • Dongguen Park
    • 2
  • Jeung Sang Go
    • 1
    Email author
  1. 1.School of Mechanical EngineeringPusan National UniversityBusanRepublic of Korea
  2. 2.Department of Advanced Materials and Parts of Transportation SystemsPusan National UniversityBusanRepublic of Korea

Personalised recommendations