Advertisement

Improving the machining efficiency of electrochemical micromachining with oscillating workpiece

  • Yufeng WangEmail author
  • Yongbin Zeng
  • Wenwu Zhang
ORIGINAL ARTICLE
  • 18 Downloads

Abstract

To enhance the machining efficiency of electrochemical micromachining (EMM), the low-frequency sinusoidal oscillating motion was applied to the workpiece, while the tool electrode moved in controlled trajectory. Mathematical model for the material removal rate (MRR) and the pressure in the interelectrode gap were derived. The mechanisms of enhancing the mass transport in the interelectrode gap induced by the oscillating workpiece during EMM have been analyzed, based on the variation of pressure in the interelectrode gap. An experimental setup has been developed for EMM. Experiments were conducted to investigate the influences of a vibrating amplitude and frequency on the machining efficiency, stability, and achievable maximum feeding rate of the tool electrode. The results indicated that a larger vibrating amplitude and a proper frequency were suitable for obtaining a higher material removal rate during EMM. The highest feeding rate of 0.3 μm/s has been obtained utilizing oscillating workpiece during the machining of microgrooves. Both the theoretical and the experimental results indicated that the oscillating workpiece during EMM was beneficial to improving the machining efficiency. Finally, microstructures with the circular profiles were processed using EMM, by a tool electrode feeding rate of 0.3 μm/s and the workpiece oscillation with the amplitude of 0.5 μm and frequency of 60 Hz.

Keywords

Electrochemical micromachining oscillation Interelectrode gap Machining efficiency Stability 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Funding information

This work was financially supported by China Postdoctoral Science Foundation (2017M621983) and Zhejiang Provincial Natural Science Foundation (LQ19E050003).

References

  1. 1.
    Lee ES, Baek SY, Cho CR (2007) A study of the characteristics for electrochemical micromachining with ultrashort voltage pulses. Int J Adv Manuf Technol 31:762–769CrossRefGoogle Scholar
  2. 2.
    Rajurkar KP, Levy G, Malshe A, Sundaram MM, McGeough J, Hu X, Resnick R, DeSilva A (2006) Micro and nano machining by electro-physical and chemical processes. CIRP Ann - Manuf Technol 55:643–666CrossRefGoogle Scholar
  3. 3.
    Schuster R, Kirchner V, Allongue P, Ertl G (2000) Electrochemical micromachining. Science 289:98–101CrossRefGoogle Scholar
  4. 4.
    Kock M, Kirchner V, Schuster R (2003) Electrochemical micromachining with ultrashort voltage pulses – a versatile method with lithographical precision. Electrochim Acta 48:3213–3219CrossRefGoogle Scholar
  5. 5.
    Ahn SH, Shi HR, Choi DK, Chu CN (2004) Electro-chemical micro drilling using ultra short pulses. Precis Eng 28:129–134CrossRefGoogle Scholar
  6. 6.
    Kim BH, Ryu SH, Choi DK, Chu CN (2005) Micro electrochemical milling. J Micromech Microeng 15:124–129CrossRefGoogle Scholar
  7. 7.
    Liu Y, Zhu D, Zhu L (2012) Micro electrochemical milling of complex structures by using in situ fabricated cylindrical electrode. Int J Adv Manuf Technol 60:977–984CrossRefGoogle Scholar
  8. 8.
    Mithu MAH, Fantoni G, Ciampi J (2011) The effect of high frequency and duty cycle in electrochemical microdrilling. Int J Adv Manuf Technol 55:921–933CrossRefGoogle Scholar
  9. 9.
    Ghoshal B, Bhattacharyya B (2015) Investigation on profile of microchannel generated by electrochemical micromachining. J Mater Process Technol 222:410–421CrossRefGoogle Scholar
  10. 10.
    Ghoshal B, Bhattacharyya B (2013) Influence of vibration on micro-tool fabrication by electrochemical machining. Int J Mach Tools Manuf 64:49–59CrossRefGoogle Scholar
  11. 11.
    Rathod V, Doloi B, Bhattacharyya B (2015) Influence of electrochemical micromachining parameters during generation of microgrooves. Int J Adv Manuf Technol 76:51–60CrossRefGoogle Scholar
  12. 12.
    Ebeid SJ, Hewidy MS, El-Taweel TA, Youssef AH (2004) Towards higher accuracy for ECM hybridized with low-frequency vibrations using the response surface methodology. J Mater Process Technol 149:432–438CrossRefGoogle Scholar
  13. 13.
    Munda J, Malapati M, Bhattacharyya B (2007) Control of micro-spark and stray-current effect during EMM process. J Mater Process Technol 194:151–158CrossRefGoogle Scholar
  14. 14.
    Bhattacharyya B, Malapati M, Munda J, Sarkar A (2007) Influence of tool vibration on machining performance in electrochemical micro-machining of copper. Int J Mach Tools Manuf 47:335–342CrossRefGoogle Scholar
  15. 15.
    Hewidy MS, Ebeid SJ, El-Taweel TA, Youssef AH (2007) Modelling the performance of ECM assisted by low frequency vibrations. J Mater Process Technol 189:466–472CrossRefGoogle Scholar
  16. 16.
    Yang I, Park MS, Chu CN (2009) Micro ECM with ultrasonic vibrations using a semi-cylindrical tool. Int J Precis Eng Manuf 10:5–10CrossRefGoogle Scholar
  17. 17.
    Zeng YB, Yu Q, Wang SH, Zhu D (2012) Enhancement of mass transport in micro wire electrochemical machining. CIRP Ann-Manuf Technol 61:195–198CrossRefGoogle Scholar
  18. 18.
    Natsu W, Nakayama H, Yu Z (2012) Improvement of ECM characteristics by applying ultrasonic vibration. Int J Precis Eng Manuf 13:1131–1136CrossRefGoogle Scholar
  19. 19.
    Xu L, Pan Y (2014) Electrochemical micromachining using vibrating tool electrode. Int J Adv Manuf Technol 75:645–650CrossRefGoogle Scholar
  20. 20.
    Wang S, Zhu D, Zeng Y, Liu Y (2011) Micro wire electrode electrochemical cutting with low frequency and small amplitude tool vibration. Int J Adv Manuf Technol 53:535–544CrossRefGoogle Scholar
  21. 21.
    Ghoshal B, Bhattacharyya B (2015) Vibration assisted electrochemical micromachining of high aspect ratio micro features. Precis Eng 42:231–241CrossRefGoogle Scholar
  22. 22.
    Wang MH, Zhang Y, He Z, Peng W (2016) Deep micro-hole fabrication in EMM on stainless steel using disk micro-tool assisted by ultrasonic vibration. J Mater Process Technol 229:475–483CrossRefGoogle Scholar
  23. 23.
    Ghoshal B, Bhattacharyya B (2014) Shape control in micro borehole generation by EMM with the assistance of vibration of tool. Precis Eng 38:127–137CrossRefGoogle Scholar
  24. 24.
    Fan ZW, Hourng LW (2011) Electrochemical micro-drilling of deep holes by rotational cathode tools. Int J Adv Manuf Technol 52:555–563CrossRefGoogle Scholar
  25. 25.
    Zhao WS, Wang ZL, Di S, Chi G, Wei Y (2002) Ultrasonic and electric discharge machining to deep and small hole on titanium alloy. J Mater Process Technol 120:101–106CrossRefGoogle Scholar
  26. 26.
    Wang Y, Zeng Y, Qu N, Zhu D (2015) Electrochemical etching of cylindrical nanoprobes using a vibrating electrolyte. Rev Sci Instrum 86:076103CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2019

Authors and Affiliations

  1. 1.Institute of Advanced Manufacturing Technology, Ningbo Institute of Materials Technology and EngineeringChinese Academy of ScienceNingboChina
  2. 2.College of Mechanical and Electrical EngineeringNanjing University of Aeronautics and AstronauticsNanjingChina

Personalised recommendations