Advertisement

Comparison of between direct and peck drilling for large aspect ratio in Ti-6Al-4V alloy

  • Abdelkrem EltaggazEmail author
  • Ibrahim Deiab
ORIGINAL ARTICLE
  • 9 Downloads

Abstract

Drilling is a crucial cutting operation as it represents 40 to 60% of the total material removed in the aircraft frame industry. Drilling difficult-to-cut materials, such as Ti-6Al-4V, is still a challenge due to their high chemical reactivity with different tool materials and low thermal conductivity. The application of cooling approach is needed to reduce the generated cutting temperature at the machining area. However, in drilling, the coolant does not sufficiently reach to the drill tip at the cutting zone because of the counter flow of the chips limits further penetration, especially in deep-hole drilling. To overcome such problems during direct drilling, different drilling techniques are followed. Peck drilling is among these methods in which the drilling process is conducted in a number of steps to achieve holes with large aspect ratio. The current study presents a detailed comparison between direct drilling and peck drilling of Ti-6Al-4V in terms of tool life, surface roughness, thrust force, torque, and burr formation. In terms of flank wear, thrust force, and burr formation, peck drilling showed better results when compared to direct drilling; however, direct drilling offers slightly better results in terms of surface quality.

Keywords

Peck drilling Direct drilling Ti-6Al-4V alloy Tool life Surface roughness Thrust force Torque And burr formation 

Notes

Acknowledgments

The authors acknowledge the support of the Natural Sciences and Engineering Research Council of Canada (NSERC) and the Ontario Centers of Excellence (OCE).

References

  1. 1.
    Hegab H, Darras B, Kishawy HA (2018). Sustainability assessment of machining with nano-cutting fluids. Procedia Manufacturing 26:245–254Google Scholar
  2. 2.
    Hegab H, Kishawy H, (2018). Towards sustainable machining of Inconel 718 using nano-fluidminimum quantity lubrication. Journal of Manufacturing and Materials Processing 2(3):50.Google Scholar
  3. 3.
    Eltaggaz A, Hegab H, Deiab I, Kishawy HA (2018). Hybrid nano-fluidminimum quantity lubrication strategy for machining austempered ductile iron (ADI). Int J Interact Des Manuf 1–9Google Scholar
  4. 4.
    Eltaggaz A, Zawada P, Hegab HA, Deiab I, Kishawy, HA (2018). Coolant strategy influence on tool life and surface roughness when machining ADI. Int J Adv Manuf Technol 94(9–12):3875–3887Google Scholar
  5. 5.
    E Commission (2011) Flightpath 2050 Europe’s Vision for Aviation. European Union, LuxembourgGoogle Scholar
  6. 6.
    Bandapalli K, Singh M (2015) Sutaria and V. Bhat, experimental investigation of machinability parameters in high-speed micro-end milling of titanium (grade-2), International. Adv Manuf Technol 85:2139–2153CrossRefGoogle Scholar
  7. 7.
    Pervaiz S, Rashid A, Deiab I, Nicolescu M (2014) Influence of tool materials on machinability of titanium- and nickel-based alloys: a review. Mater Manuf Process 29(3):219–252CrossRefGoogle Scholar
  8. 8.
    Pervaiz S, Rashid A, Deiab I, Nicolescu C (2016) An experimental investigation on the effect of minimum quantity cooling lubrication (MQCL) in machining titanium alloy (Ti6Al4V). Int J Manuf Technol 87:1371–1386CrossRefGoogle Scholar
  9. 9.
    Pramanik A (2014) Problems and solutions in machining of titanium alloys. Int J Adv Manuf Technol 70:919–928CrossRefGoogle Scholar
  10. 10.
    Sharif S, Abd Rahim E (2007) Performance of coated-and uncoated-carbide tools when drilling titanium alloy-Ti6Al4V. J Mater Process Technol 185(1–3):72–76CrossRefGoogle Scholar
  11. 11.
    Yip W, To S (2017) Tool life enhancement in dry diamond turning of titanium alloys using an eddy current damping and a magnetic field for sustainable manufacturing. J Clean Prod 168:929–939CrossRefGoogle Scholar
  12. 12.
    Ezugwu E, Wang Z (1997) Titanium alloys and their machinability—a review. J Mater Process Technol 68:262–274CrossRefGoogle Scholar
  13. 13.
    Mathew NT, Vijayaraghavan L (2016) Drilling of titanium aluminide at different aspect ratio under dry and wet conditions. J Manuf Process 24:256–269CrossRefGoogle Scholar
  14. 14.
    Ravisubramanian S, Shunmugam MS (2018) Investigations into peck drilling process for large aspect ratio microholes in aluminum 6061-T6. Mater Manuf Process 33(9):935–942CrossRefGoogle Scholar
  15. 15.
    Duck WK, Young SL, Min SP, Chong NC (2009) Tool life improvement by peck drilling and thrust force monitoring during deep-micro-hole drilling of steel. Int J Mach Tool Manu 49:246–255CrossRefGoogle Scholar
  16. 16.
    Nakagawa H, Ogawa K, Kihara A, Hirogaki T (2007) Improvement of micro-drilled hole quality for printed wiring boards. J Mater Process Technol 191:293–296CrossRefGoogle Scholar
  17. 17.
    Csala V, Szalay T, Farkas B, Markos S (2015) Application benchmark of three micro hole machining processes for manufacturing the nozzle of a medical water jet machine. Acta Polytech Hung 12(2):53–69Google Scholar
  18. 18.
    Bagci E, Ozcelik B (2006) Investigation of the effect of drilling condition on the twist drill temperature during step-by-step and continuous dry drilling. Mater Des 27:446–454CrossRefGoogle Scholar
  19. 19.
    Abdelhafeez AM, Soo SL, Aspinwall DK, Dowson A, Arnold D (2015) Burr formation and hole quality when drilling titanium and aluminum alloys. Procedia CIRP 37:230–235CrossRefGoogle Scholar
  20. 20.
    Ko S-L, Chang J-E, Yang G-E (2003) Burr minimizing scheme in drilling. J Mater Process Technol 140(1–3):237–242CrossRefGoogle Scholar
  21. 21.
    Abele E, Elsenheimer J, Hohenstein J, Tschannerl M (2005) Influence of drill dynamics on bore quality. CIRP Ann Manuf Technol 54:83–86CrossRefGoogle Scholar
  22. 22.
    T C & G. F. CORPORATION (2017) [Online]. Available: http://pdocs.masterchemical.com/mcc/docs/db-docs/pdf_di/MicroSol_690XT.pdf. [Accessed 4 Jan 2019]
  23. 23.
    Muthukrishnan N, Davim P (2011) Influence of coolant in machinability of titanium alloy (Ti-6Al-4V). Journal of Surface Engineered Materials and Advanced Technology 1(1):9–14.  https://doi.org/10.4236/jsemat.2011.11002. Accessed April 2011CrossRefGoogle Scholar
  24. 24.
    Dolinsek S, Sustarsic B, Kopac J (2001) Wear mechanism of cutting tools in high speed cutting process. Wear 250:349–352CrossRefGoogle Scholar
  25. 25.
    Ozden I, Elaheh G (2013) Comparative study of tool life and hole quality in drilling of CFRP/titanium stack using coated carbide drill. Mach Sci Technol 17:380–409CrossRefGoogle Scholar
  26. 26.
    Mathew N, Vijayaraghavan L (2017) Environmentally friendly drilling of intermetallic titanium aluminide at different aspect ratio. J Clean Prod 141:439–452CrossRefGoogle Scholar
  27. 27.
    Pervaiz S, Rashid A I. Deiab and M NicolescuGoogle Scholar
  28. 28.
    Aurich J, Dornfeld D, Arrazola P, Frank V, Leitz L, Min S (2009) Burrs-analysis, control and removal, CIRP Annual- MAnufacture. Technology 58(2)Google Scholar
  29. 29.
    Ozden I, Elaheh G (2013) Comparative study of tool life and hole quality in drilling of CFRPcfrp/titanium stack using coated carbide drill. Mach Sci Technol 17(3):380–409CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2019

Authors and Affiliations

  1. 1.Advanced Manufacturing Lab (AML), School of EngineeringUniversity of GuelphGuelphCanada

Personalised recommendations