Advertisement

Experimental evaluation of the lubrication performances of different nanofluids for minimum quantity lubrication (MQL) in milling Ti-6Al-4V

  • Xiufang Bai
  • Changhe Li
  • Lan Dong
  • Qingan Yin
ORIGINAL ARTICLE
  • 17 Downloads

Abstract

The objective of this research is to experimentally evaluate the lubrication performances of different nanofluids in milling titanium alloy Ti-6Al-4V. Six types of nanofluids, namely, Al2O3, SiO2, MoS2, CNTs, SiC, and graphite, were selected. Cottonseed oil was used as the base oil. The lubrication performance was investigated in terms of milling force, surface roughness, and morphology of workpiece surface. Experimental results demonstrated that the Al2O3 nanoparticle obtained the minimal milling force (Fx = 277.5 N, Fy = 88.3 N), followed by the SiO2 nanoparticle (Fx = 283.6 N, Fy = 86.5 N). The surface roughness obtained by the Al2O3 nanofluid was the minimum (Ra = 0.594 μm), whereas it was the maximum by using minimum quantity lubrication (Ra = 1.772 μm). The surface roughness of the six nanofluids was described by the following order: Al2O3 < SiO2 < MoS2 < CNTs < graphite < SiC. The workpiece surface morphology was the best for Al2O3 and SiO2. The viscosity of the nanofluids was also analyzed. Spherical Al2O3 and SiO2 nanoparticles improved the lubrication effect of base oil mostly and were more suitable as environment-friendly additives for the base oil compared with the others.

Keywords

Milling Nanofluid Minimum quantity lubrication Surface morphology 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Funding

This research was financially supported by the following organizations: the National Natural Science Foundation of China (51806112 and 51575290); Shandong Provincial Natural Science Foundation, China (ZR2017PEE002 and ZR2017PEE011); and the Scientific Research Development Project of Shandong Higher Education Institutions, China (J18KA017 and J17KB016).

References

  1. 1.
    Ulutan D, Ozl T (2011) Machining induced surface integrity in titanium and nickel alloys. Int J Machine Tools Manuf 55:250–280CrossRefGoogle Scholar
  2. 2.
    Su Y, He N, Li L (2010) Experimental study on high speed milling titanium alloys using cryogenic minimum quantity. China Mech Eng 21:2665–2670Google Scholar
  3. 3.
    Ekinovic S, Prcanovic H, Begovic E (2015) Investigation of influence of MQL machining parameters on cutting forces during MQL turning of carbon steel St52-3. Rrocescia Eng 132:608–614Google Scholar
  4. 4.
    Khan MMA, Mithu MAH, Dhar NR (2009) Effects of minimum quantity lubrication onturning AISI 9310 alloysteel using vegetable oil-based cutting fluid. J Mater Process Technol 209:5573–5583CrossRefGoogle Scholar
  5. 5.
    Li CH, Li JY, Wang S, Jia DZ (2013) Modeling and numerical simulation of the grinding temperature distribution with nano-particle jet of MQL. Adv Mech Eng 7:167–181Google Scholar
  6. 6.
    Pervaiz S, Rashid A, Deiab I, Nicolescu CM (2016) An experimental investigation on effect of minimum quantity cooling lubrication(MQCL) in machining titanium alloy (Ti6Al4V). Int J Adv Manuf Technol 87:1371–1386CrossRefGoogle Scholar
  7. 7.
    Rahim E, Sasahara H (2011) A study of the effect of palm oil as MQL lubricant on high speed drilling of titanium alloys. Tribol Int 44:309–317CrossRefGoogle Scholar
  8. 8.
    Mark BD, Sabarish VN, Hariharan MV, Samuel RD (2018) On the benefits of sub-zero air upplemented minimum quantity lubrication systems: an experimental and mechanistic investigation on end milling of Ti-6Al-4V alloy. Tribol Int 119:464–473CrossRefGoogle Scholar
  9. 9.
    Ding WF, Zhang LC, Li Z, Zhu YJ, Su HH, Xu JH (2017) Review on grinding-induced residual stresses in metallic materials. Int J Adv Manuf Technol 88:2939–2968CrossRefGoogle Scholar
  10. 10.
    Ding WF, Barbara L, Zhu YJ, Li Z, Fu YC, Su HH, Xu JH (2017) Review on monolayer CBN superabrasive wheels for grinding metallic materials. Chin J Aeronaut 30:109–134CrossRefGoogle Scholar
  11. 11.
    Wang YG, Li CH, Zhang YB, Yang M, Li BK, Jia DZ, Hou YL, Mao C (2016) Experimental evaluation of the lubrication properties of the wheel/workpiece interface in minimum quantity lubrication (MQL) grinding using different types of vegetable oils. J Clean Prod 127:487–499CrossRefGoogle Scholar
  12. 12.
    Li BK, Li CH, Zhang YB, Wang YG, Yang M, Jia DZ, Zhang NQ, Wu QD (2017) Effect of the physical properties of different vegetable oil-based nanofluids on MQLC grinding temperature of Ni-based alloy. Int J Adv Manuf Technol 89:3459–3474CrossRefGoogle Scholar
  13. 13.
    Zhang YB, Li CH, Ji HJ, Yang XH, Yang M, Jia DZ, Zhang XP, Li RZ, Wang J (2017) Analysis of grinding mechanics and improved predictive force model based on material-removal and plastic-stacking mechanisms. Int J Mach Tools Manuf 122:81–97CrossRefGoogle Scholar
  14. 14.
    Park KH, Ewald B, Kwon PY (2011) Effect of nano-enhanced lubricant in minimum quantity lubrication balling milling. J Tribol 133:3526–3537CrossRefGoogle Scholar
  15. 15.
    Zhang DK, Li CH, Jia DZ, Zhang YB, Zhang XP (2015) Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding. Chin J Aeronaut 28:570–581CrossRefGoogle Scholar
  16. 16.
    Zhang XP, Li CH, Zhang YB, Jia DZ, Li BK, Wang YG, Yang M, Hou YL, Zhang XW (2016) Performances of Al2O3/SiC hybrid nanofluids in minimum-quantity lubrication grinding. Int J Adv Manuf Technol 86(1–15):3427–3441CrossRefGoogle Scholar
  17. 17.
    Wang YG, Li CH, Zhang YB, Yang M, Zhang XP, Zhang NQ, Dai JJ (2016) Experimental evaluation on tribological performance of the wheel/workpiece interface in minimum quantity lubrication grinding with different concentrations of Al2O3 nanofluids. J Clean Prod 142:3571–3583CrossRefGoogle Scholar
  18. 18.
    Mao C, Tang XJ, Zou HF, Huang XM, Zhou ZX (2012) Investigation of grinding characteristic using nanofluid minimum quantity lubrication. Int J Precis Eng Man 13:1745–1752CrossRefGoogle Scholar
  19. 19.
    Mao C, Zou HF, Huang XM, Zhang JA Zhou ZX (2013) The influence of spraying parameters on grinding performance for nanofluid minimum quantity lubrication. Int J Adv Manuf Technol 64:1791–1799CrossRefGoogle Scholar
  20. 20.
    Shen B, Shih AJ, Tung SC (2008) Application of nanofluids in minimum quantity lubrication grinding. Tribol T 51:730–737CrossRefGoogle Scholar
  21. 21.
    Shen B, Kalita P, Malshe AP, Shih A (2008) Performance of novel MoS2 nanoparticles based grinding fluids in minimum quantity lubrication grinding. Trans NAMRI/SME 36:357–364Google Scholar
  22. 22.
    Kalita P, Malshe AP, Kumar SA, Yoganath VG, Gurumurthy T (2012) Study of specific energy and friction coefficient in minimum quantity lubrication grinding using oil-based nanolubricants. J Manuf Process 14:160–166CrossRefGoogle Scholar
  23. 23.
    Krishna PV, Srikant RR, Rao DN (2010) Experimental investigation on the performance of nanoboric acid suspensions in SAE-40 and coconut oil during turning of AISI 1040 steel. Int J Mach Tools Manuf 50:911–916CrossRefGoogle Scholar
  24. 24.
    Rao SN, Satyanarayana B (2011) Experimental estimation of tool wear and cutting temperatures in MQL using cutting fluids with CNT inclusion. Int J Eng Sci Technol 3:928–931CrossRefGoogle Scholar
  25. 25.
    Yan J, Zhang Z, Kuriyagawa T (2011) Effect of nanoparticle lubrication in diamond turning of reaction-bonded SiC. Int J Autom Technol 5:307–312CrossRefGoogle Scholar
  26. 26.
    Khandekar S, Sankar MR, Agnihotri V, Ramkumar J (2012) Nano-cutting fluid for enhancement of metal cutting performance. Mater Manuf Process 27:963–967CrossRefGoogle Scholar
  27. 27.
    Prasad MMS, Srikant RR (2013) Performance evaluation of nano graphite inclusion in cutting fluids with MQL technique in turning of AISI 1040 steel. Int J Res Eng Technol 2:381–393Google Scholar
  28. 28.
    Su Y, Gong L, Li B, Liu Z, Chen D (2016) Performance evaluation of nanofluid MQL with vegetable-based oil and ester oil as base fluids in turning. Int J Adv Manuf Technol 83:2083–2089CrossRefGoogle Scholar
  29. 29.
    Sayuti M, Sarhan AAD, Hamdi M (2013) An investigation of optimum SiO2 nanolubrication parameters in end milling of aerospace Al6061-T6 alloy. Int J Adv Manuf Technol 67:833–849CrossRefGoogle Scholar
  30. 30.
    Sayuti EO, Sarhan AAD (2013) Investigation on the morphology of the machined surface in end milling of aerospace AL6061-T6 for novel uses of SiO2 nanolubrication system. J Cleaner Prod 66:655–663CrossRefGoogle Scholar
  31. 31.
    Ming EO, Sayuti M, Sarhan AAD (2015) Fuzzy logic-based approach to investigate the novel uses of nano suspended lubrication in precise machining of aerospace AL tempered grade 6061. J Clean Prod 89:286–295CrossRefGoogle Scholar
  32. 32.
    Marcon A, Melkote S, Kalaitzidou K, DeBra D (2010) An experimental evaluation of graphite nanoplatelet base-d lubricant in micro-milling. CIRP Ann Manuf Technol 59:141–144CrossRefGoogle Scholar
  33. 33.
    Rahmati B, Sarhan AAD, Sayut M (2013) Morphology of surface generated by end milling AL6061-T6 using molybdenum disulfide (MoS2) nanolubrication in end milling machining. J Clean Prod 66:685–691CrossRefGoogle Scholar
  34. 34.
    Rahmati B, Sarhan AAD, Sayuti M (2014) Investigating the optimum molybdenum disulfide (MoS2) nanolu-brication parameters in CNC milling of AL6061-T6 alloy. Int J Adv Manuf Technol 70:1143–1155CrossRefGoogle Scholar
  35. 35.
    Uysal A, Demiren F, Altan E (2015) Applying minimum quantity lubrication (MQL) method on milling of martensitic stainless steel by using nano MoS2 reinforced vegetable cutting fluid. Procedia Soc Behav Sci 195:2742–2747CrossRefGoogle Scholar
  36. 36.
    Najiha MS, Rahman MM, Kadirgama K (2016) Performance of water-based TiO2 nanofluid during the minim-um quantity lubrication machining of aluminium alloy AA6061-T6. J Clean Prod 135:1623–1636CrossRefGoogle Scholar
  37. 37.
    Hadi M, Atefi R (2015) Effect of minimum quantity lubrication with gamma-Al2O3 nanoparticles on surface roughness in milling AISI D3 steel. Ind J Sci Technol 8:296–300CrossRefGoogle Scholar
  38. 38.
    Yin QA, Li CH, Zhang YB, Yang M, Jia DZ, Hou YL, Li RZ, Dong L (2018) Spectral analysis and power spectral density evaluation in Al2O3 nanofluid minimum quantity lubrication milling of 45 steel. Int J Adv Manuf Technol 97:129–145CrossRefGoogle Scholar
  39. 39.
    Kim JS, Kim JW, Lee SW (2017) Experimental characterization onm icro-end milling of titanium alloy using nanofluid minimum quantity lubrication with chilly gas. Int J Adv Manuf Technol 91:2741–2749CrossRefGoogle Scholar
  40. 40.
    Li M, Yu TB, Zhang RC (2018) MQL milling of TC4 alloy by dispersing graphene into vegetable oil-based cutting fluid. Int J Adv Manuf Technol 99:1735–1753Google Scholar
  41. 41.
    Lee PH, Nam JS, Li C, Lee SW (2012) An experimental study on micro-grinding process with nanofluid minimum quantity lubrication (MQL). Int J Precis Eng Manuf 13:331–338CrossRefGoogle Scholar
  42. 42.
    Shi XL, Xiu SC, Zhang XM, Wang YS (2017) A study of PSHG and its characteristic mechanism of residual stress within a hardened layer. Int J Adv Manuf Technol 88(1):863–877CrossRefGoogle Scholar
  43. 43.
    Deng YS, Xiu SC, Shi XL, Sun C, Wang YS (2017) Study on the effect mechanisms of pre-stress on residual stress and surface roughness in PSHG. Int J Adv Manuf Technol 88(9-12):3243–3256CrossRefGoogle Scholar
  44. 44.
    Sia SY, Bassyony EZ, Sarhan AA (2014) Development of SiO2 nanolubrication system to be used in sliding bearings. Int J Adv Manuf Technol 71:1277–1284CrossRefGoogle Scholar
  45. 45.
    Guo SM, Li CH, Zhang YB, Wang YG, Li BK, Yang M, Zhang XP, Liu GT (2016) Experimental evaluation of the lubrication performance of mixtures of castor oil with other vegetable oils in MQL grinding of nickel-based alloy. J Clean Prod 140:1060–1076CrossRefGoogle Scholar
  46. 46.
    Yang M, Li CH, Zhang YB, Jia DZ, Zhang XP, Hou YL, Li RZ, Wang J (2017) Maximum undeformed equivalent chip thickness for ductile-brittle transition of zirconia ceramics under different lubrication conditions. Int J Mach Tools Manuf 122:55–65CrossRefGoogle Scholar
  47. 47.
    Ge XY, Xia YQ, Cao ZF (2015) Tribological properties and insulation effect of nanometer TiO2 and nanometer SiO2 as additives in grease. Tribol Int 92:454–461CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2018

Authors and Affiliations

  • Xiufang Bai
    • 1
    • 2
  • Changhe Li
    • 3
  • Lan Dong
    • 1
    • 2
  • Qingan Yin
    • 3
  1. 1.Engineering and Technology R&D Center of Mechanical and Electrical in Colleges of ShandongQingdao Binhai UniversityQingdaoChina
  2. 2.School of Mechanical and Electrical EngineeringQingdao Binhai UniversityQingdaoChina
  3. 3.School of Mechanical and Automotive EngineeringQingdao University of TechnologyQingdaoChina

Personalised recommendations