Advertisement

Minimizing drum-shaped inaccuracy in high-speed wire electrical discharge machining after multiple cuts

  • Cong Deng
  • Zhidong Liu
  • Ming Zhang
  • Yichao Ji
  • Hongwei Pan
ORIGINAL ARTICLE
  • 6 Downloads

Abstract

Drum-shaped inaccuracy increases dramatically in high-speed wire electrical discharge machining (HS-WEDM) after multiple cuts when very thick workpiece (> 100 mm) are used. To tackle this problem, a positional change model of the wire electrode was established to analyze the main causes of the drum-shaped inaccuracy. In HS-WEDM, the conductivity of the working fluid is very high. As the workpiece thickness increases, the “leakage current” at the machining gap increases, and more energy is required for the trim cuts. In addition, to maintain stable trim cuts, a long pulse-on time is needed. As a result, the high discharge energy inevitably results in a large explosive force, which increases the wire bending deformation due to long durations under this force. To solve these problems, novel measures were taken in this study. First, an improved working fluid was proposed to reduce the conductivity so that the energy loss between the electrodes can be decreased. The discharge energy used for the trim cuts was diminished to reduce the impact of the discharge explosive force. Second, a short pulse-on time and a high peak current were utilized for the trim cuts to reduce the impulse from the effect of the discharge explosive force on the wire electrode. Third, a closed-loop tension mechanism was designed to increase the wire tension, thereby improving the stability and rigidity of wire electrode. Finally, the rigidity of wire electrode was further improved by utilizing a unique trim-cut method proposed in this study. The experimental results showed that the drum-shaped inaccuracy of a workpiece with a thickness of 150 mm was reduced to 10 μm from 25 μm after three cuts (one roughing cut and two finish/trim cuts) under normal machining and the quality and uniformity of the machined surface were improved.

Keywords

High-speed reciprocating traveling WEDM High thickness Multiple cuts Drum-shaped inaccuracy 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Acknowledgements

The authors also extend their sincere thanks to those who contributed in the preparation of the instructions.

Funding information

This project is supported by the National Natural Science Foundation of China (Grant No.51575271).

References

  1. 1.
    Zhu N, Ye J, Han FZ (2010) Development trends of WEDM technology. Electromach Mould B04:53–59Google Scholar
  2. 2.
    Liu ZD (2013) Current situation and development of HS-WEDM. Mach Build Autom 2:1–6Google Scholar
  3. 3.
    Liu ZD (2011) Application and processing of electrical machining. National Defense of Industry Press, BeijingGoogle Scholar
  4. 4.
    Liu ZD (2017) The past, present and future of medium-speed wire cut electrical discharge machine tools. Electromach Mould A01:12–19Google Scholar
  5. 5.
    Takayama Y, Makino Y, Niu Y, Uchida H (2016) The latest technology of wire-cut EDM[C]//18th CIRP conference on electro physical and chemical machining, science direct 623–626Google Scholar
  6. 6.
    Liu ZD (2015) Development bottlenecks and research thinking in HS-WEDM[C]//16th China Symposium on non-traditional machining 305–312Google Scholar
  7. 7.
    Han F, Kunieda M, Sendai T (2002) High precision simulation of WEDM using parametric programming. CIRP Ann Manuf Technol 51(1):165–168CrossRefGoogle Scholar
  8. 8.
    Li LL, Liu ZD (2016) Study on the factors of repeated cutting flatness for high thickness workpiece in WEDM. Electromach mould 4:12–16Google Scholar
  9. 9.
    Zhang G, Chen Z, Zhang Z (2014) A macroscopic mechanical model of wire electrode deflection considering temperature increment in MS-WEDM process. Int J Mach Tools Manuf 78:41–53CrossRefGoogle Scholar
  10. 10.
    Adachi Y, Yoshida M, Kunieda M (1997) Study on process reaction force caused by bubble formation in EDM. JSEME 31(67):23–30Google Scholar
  11. 11.
    Plaza S, Ortega N, Sanchez JA (2009) Original models for the prediction of angular error in wire-EDM taper-cutting. Int J Adv Manuf Technol 44(5–6):529–538CrossRefGoogle Scholar
  12. 12.
    Luo YF (1999) Rupture failure and mechanical strength of the electrode wire used in wire EDM. J Mater Process Technol 94(2–3):208–215CrossRefGoogle Scholar
  13. 13.
    Li C, Liu Z, Fang L (2018) Super-high-thickness high-speed wire electrical discharge machining. Int J Adv Manuf Technol 95(5–8):1805–1818CrossRefGoogle Scholar
  14. 14.
    Han F, Kunieda M, Sendai T (2002) Simulation on influence of electrostatic force on machining characteristics in WEDM. IJEM 7:31–36CrossRefGoogle Scholar
  15. 15.
    Yan MT, Wang PW, Lai JC (2016) Improvement of part straightness accuracy in rough cutting of wire EDM through a mechatronic system design. Int J Adv Manuf Technol 84(9–12):2623–2635CrossRefGoogle Scholar
  16. 16.
    Wu Q, Liu Z, Zhang B (2017) Experimental research on tension balance control of reciprocating winding diamond wire saw. Int J Adv Manuf Technol 91(1–4):423–431CrossRefGoogle Scholar
  17. 17.
    Wei W, Liu ZD, Wang ZX (2010) Research on multi-cutting of low speed unidirectional travelling wire in the high-low traveling speed WEDM machine. Electromach Mould 6:51–55Google Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2019

Authors and Affiliations

  • Cong Deng
    • 1
  • Zhidong Liu
    • 1
  • Ming Zhang
    • 1
  • Yichao Ji
    • 1
  • Hongwei Pan
    • 1
  1. 1.College of Mechanical and Electrical EngineeringNanjing University of Aeronautics and AstronauticsNanjingChina

Personalised recommendations