Advertisement

Characterization and formation mechanism of periodic solidification defects in deep-penetration laser welding of NiCrMoV steel with heavy section

  • Yu Sun
  • Haichao Cui
  • Xinhua Tang
  • Fenggui LuEmail author
ORIGINAL ARTICLE
  • 26 Downloads

Abstract

With the thickness increasing of steel, application of laser beam welding on heavy section has been arousing broadly interests. Deep-penetration laser welding was performed on thick plate of NiCrMoV steel, and the characteristics of welding defects were analyzed in terms of their formation and distribution. The periodic defects were found to occur frequently at the central longitudinal section of the bead-on-plate welds that have a certain distance from fusion line. The formation and distribution of these defects were deemed as unique for deep-penetration laser welding on heavy plate due to mismatch of welding parameters with weld profile. Defect susceptibility was raised firstly and reduced subsequently as the heat input decreased, and a large amount of periodic solidification defects should occur when penetration-to-width ratio (aspect ratio) is higher than 4.0. By means of detail characterization on defect by optical microscopy (OM), scanning electron microscopy (SEM), and energy-dispersive spectroscopy (EDS), the periodic defects were proved to be hot cracking defects induced by contact and rapid shrinkage of transverse columnar crystals in mid part of the welds before feeding in sufficient liquid. The formation of periodic solidification defects in welds was greatly related to weld profile and cooling rate limited by the heat dissipation conditions. The optimized parameters to avoid periodic solidification defects were determined for deep-penetration laser welding of this steel.

Keywords

Deep-penetration laser welding Heavy plate Periodic solidification defects Hot cracking Weld profile 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

Notes

Funding information

This work is financially supported by the National Natural Science Foundation of China (Nos. 51675336 and U1660101).

References

  1. 1.
    Atabaki MM, Yazdian N, Ma J, Kovacevic R (2016) High power laser welding of thick steel plates in a horizontal butt joint configuration. Opt Laser Technol 83:1–12.  https://doi.org/10.1016/j.optlastec.2016.03.016 CrossRefGoogle Scholar
  2. 2.
    Lee SJ, Katayama S, Kawahito Y, Kinoshita K, Kim JD (2013) Weldability and keyhole behavior of Zn-coated steel in remote welding using disk laser with scanner head. J Laser Appl 25(3):103–103.  https://doi.org/10.2351/1.4795456 CrossRefGoogle Scholar
  3. 3.
    Lin R, Wang HP, Lu F, Solomon J, Carlson BE (2017) Numerical study of keyhole dynamics and keyhole-induced porosity formation in remote laser welding of Al alloys. Int J Heat Mass Tran 108:244–256.  https://doi.org/10.1016/j.ijheatmasstransfer.2016.12.019 CrossRefGoogle Scholar
  4. 4.
    Sun J, Nie P, Lu F, Huang J, Feng K, Li Z, Guo B, Jiang E, Zhang W (2017) The characteristics and reduction of porosity in high-power laser welds of thick AISI 304 plate. Int J Adv Manuf Technol 93:3517–3530.  https://doi.org/10.1007/s00170-017-0734-y CrossRefGoogle Scholar
  5. 5.
    Kou S (2003) Welding metallurgy, Second Edition  https://doi.org/10.1002/0471434027
  6. 6.
    Tsukamoto S (2011) High speed imaging technique part 2—high speed imaging of power beam welding phenomena. Sci Technol Weld Joi 16(1):44–55.  https://doi.org/10.1179/136217110X12785889549949 CrossRefGoogle Scholar
  7. 7.
    Lippold JC (1985) Centerline cracking in deep penetration electron beam welds in type 304L stainless steel. Weld J (Miami); (United States) 64:5 (5):S127-S136. https://app.aws.org/wj/supplement/WJ_1985_05_s127.pdf
  8. 8.
    Zhang Y, Lu F, Cui H, Cai Y, Guo S, Tang X (2016) Investigation on the effects of parameters on hot cracking and tensile shear strength of overlap joint in laser welding dissimilar Al alloys. Int J Adv Manuf Technol 86(9–12):1–10.  https://doi.org/10.1007/s00170-016-8383-0 Google Scholar
  9. 9.
    Wang X, Wang HP, Lu F, Carlson BE, Wu Y (2014) Analysis of solidification cracking susceptibility in side-by-side dual-beam laser welding of aluminum alloys. Int J Adv Manuf Technol 73(1–4):73–85.  https://doi.org/10.1007/s00170-014-5810-y CrossRefGoogle Scholar
  10. 10.
    Schaefer M, Kessler S, Scheible P, Speker N, Harrer T (2017) Hot cracking during laser welding of steel: influence of the welding parameters and prevention of cracks. Proc of SPIE.  https://doi.org/10.1117/12.2254424
  11. 11.
    Schaefer M, Kessler S, Fetzer F, Graf T (2017) Influence of the focal position on the melt flow during laser welding of steel. J Laser Appl 29(1):012010.  https://doi.org/10.2351/1.4972098 CrossRefGoogle Scholar
  12. 12.
    Schaefer M, Kessler S, Scheible P, Graf T (2017) Modulation of the laser power to prevent hot cracking during laser welding of tempered steel. J Laser Appl 29(4):042008.  https://doi.org/10.2351/1.4989766 CrossRefGoogle Scholar
  13. 13.
    Salemi A, Abdollah-Zadeh A (2008) The effect of tempering temperature on the mechanical properties and fracture morphology of a NiCrMoV steel. Mater Charact 59(4):484–487.  https://doi.org/10.1016/j.matchar.2007.02.012 CrossRefGoogle Scholar
  14. 14.
    Tanaka Y, Azuma T, Yaegashi N (1994) Isothermal aging test results (up to 100 000 h) of NiCrMoV steels for low-pressure steam turbine. Int J Pres Ves Pip 59(1–3):71–81.  https://doi.org/10.1016/0308-0161(94)90143-0 CrossRefGoogle Scholar
  15. 15.
    Bandyopadhyay N, Briant CL, Hall EL (1985) Carbide precipitation, grain boundary segregation, and temper embrittlement in NiCrMoV rotor steels. Metall Trans A 16(5):721–737.  https://doi.org/10.1007/BF02814824 CrossRefGoogle Scholar
  16. 16.
    Lu F, Liu X, Wang P, Wu Q, Cui H, Huo X (2015) Microstructural characterization and wide temperature range mechanical properties of NiCrMoV steel welded joint with heavy section. J Mater Res 30(13):2108–2116.  https://doi.org/10.1557/jmr.2015.162 CrossRefGoogle Scholar
  17. 17.
    Liu P, Lu F, Liu X, Ji H, Gao Y (2014) Study on fatigue property and microstructure characteristics of welded nuclear power rotor with heavy section. J Alloy Compd 584(25):430–437.  https://doi.org/10.1016/j.jallcom.2013.09.048 CrossRefGoogle Scholar
  18. 18.
    Li Y, Cai Z, Li K, Pan J, Liu X, Sun L, Wang P (2018) Investigation of local brittle zone in multipass welded joint of NiCrMoV steel with heavy section. J Mater Res 33(8):923–934.  https://doi.org/10.1557/jmr.2017.467 CrossRefGoogle Scholar
  19. 19.
    Pouraliakbar H, Khalaj M, Nazerfakhari M, Khalaj G (2015) Artificial neural networks for hardness prediction of HAZ with chemical composition and tensile test of X70 pipeline steels. J Iron Steel Res Int 22(5):446–450.  https://doi.org/10.1016/S1006-706X(15)30025-X CrossRefGoogle Scholar
  20. 20.
    Mohanty PS, Mazumder J (1998) Solidification behavior and microstructural evolution during laser beam—material interaction. Metall Mater Trans B Process Metall Mater Process Sci 29(6):1269–1279.  https://doi.org/10.1007/s11663-998-0050-x CrossRefGoogle Scholar
  21. 21.
    Bermejo M-AV, DebRoy T, Hurtig K, Karlsson L, Svensson L-E (2015) Towards a map of solidification cracking risk in laser welding of austenitic stainless steels. Phys Procedia 78:230–239.  https://doi.org/10.1016/j.phpro.2015.11.033 CrossRefGoogle Scholar
  22. 22.
    Chelladurai AM, Gopal KA, Murugan S, Albert SK, Venugopal S, Jayakumar T (2015) Effect of energy transfer modes on solidification cracking in pulsed laser welding. Sci Technol Weld Joi 20(7):578–584.  https://doi.org/10.1179/1362171815Y.0000000041 CrossRefGoogle Scholar
  23. 23.
    Sheikhi M, Malek Ghaini F, Assadi H (2015) Prediction of solidification cracking in pulsed laser welding of 2024 aluminum alloy. Acta Mater 82:491–502.  https://doi.org/10.1016/j.actamat.2014.09.002 CrossRefGoogle Scholar
  24. 24.
    Enz J, Carrarin C, Riekehr S, Ventzke V, Kashaev N (2017) Hot cracking behaviour of an autogenously laser welded Al-Cu-Li alloy. Int J Adv Manuf Technol 6:1–12.  https://doi.org/10.1007/s00170-017-1197-x Google Scholar
  25. 25.
    Murthy NK, Ram GDJ (2016) Hot cracking behavior of carbide-free bainitic weld metals. Mater Design 92:88–94.  https://doi.org/10.1016/j.matdes.2015.12.020 CrossRefGoogle Scholar
  26. 26.
    Pineda Huitron RM, Vuorinen E Hot cracking of structural steel during laser welding (2017).  https://doi.org/10.1088/1757-899X/258/1/012005
  27. 27.
    Lippold JC (2015) Welding metallurgy and weldability.  https://doi.org/10.1002/9781118960332
  28. 28.
    Katayama S, Kawahito Y, Mizutani M (2010) Elucidation of laser welding phenomena and factors affecting weld penetration and welding defects. Phys Procedia 5:9–17.  https://doi.org/10.1016/j.phpro.2010.08.024 CrossRefGoogle Scholar
  29. 29.
    Li X, Lu F, Cui H, Tang X, Wu Y (2014) Numerical modeling on the formation process of keyhole-induced porosity for laser welding steel with T-joint. Int J Adv Manuf Technol 72(1–4):241–254.  https://doi.org/10.1007/s00170-014-5609-x CrossRefGoogle Scholar
  30. 30.
    Cho WI, Na SJ, Thomy C, Vollertsen F (2012) Numerical simulation of molten pool dynamics in high power disk laser welding. J Mater Process Technol 212(1):262–275.  https://doi.org/10.1016/j.jmatprotec.2011.09.011 CrossRefGoogle Scholar
  31. 31.
    Campbell J, Freng O (2003) Castings (Second Edition). Butterworth, Oxford  https://doi.org/10.1016/B978-075064790-8/50030-9

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2018

Authors and Affiliations

  1. 1.Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and EngineeringShanghai Jiao Tong UniversityShanghaiPeople’s Republic of China
  2. 2.Collaborative Innovation Center for Advanced Ship and Deep-Sea ExplorationShanghaiPeople’s Republic of China

Personalised recommendations