Experimental investigation of cooling characteristics in wet grinding using heat pipe grinding wheel

  • Qingshan He
  • Yucan Fu
  • Jiajia Chen
  • Wei Zhang
  • Zhongming Cui
ORIGINAL ARTICLE
  • 39 Downloads

Abstract

High grinding temperature restricts the machining efficiency and precision of some aeronautical difficult-to-machine materials. Aiming to enhance heat exchange with the grinding zone and reduce grinding temperature, heat pipe grinding wheel (HPGW) provides a novel method through improving the thermal conductivity of grinding wheel assisted by heat pipe. In this paper, the structure of HPGW is introduced and the workpiece temperature and energy partition in wet grinding using HPGW based on a wheel-fluid composite surface model is analyzed. Wet grinding experiments including creep feed grinding, high-speed shallow grinding and high-efficiency deep grinding (HEDG) are carried to investigate the cooling characteristics of HPGW according to the workpieces of titanium alloy Ti-6A1-6 V and Inconel 718. Compared with using the traditional grinding wheel, the results show that using HPGW in creep feed grinding and HEDG can maintain a lower grinding temperature and avoid the burnout under a relatively high removal rate, but cooling effect of HPGW is not obviously different from the traditional grinding wheel in high-speed shallow grinding due to a small heat input at the evaporator of HPGW.

Keywords

Heat pipe grinding wheel Grinding Temperature Cooling 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Harebell S, Woolley NH, Tridimas YD, Allanson DR, Rowe WB (2000) The effects of cutting fluid application methods on the grinding process. Int J Mach Tool Manu 40:209–223CrossRefGoogle Scholar
  2. 2.
    Morgan MN, Jackson AR, Wu H, Baines-Jones V, Batako A, Rowe WB (2008) Optimisation of fluid application in grinding. CIRP Ann Manuf Technol 57:363–366CrossRefGoogle Scholar
  3. 3.
    Mao C, Tang XJ, Zou HF, Zhou ZX, Yin WW (2012) Experimental investigation of surface quality for minimum quantity oil–water lubrication grinding. Int J Adv Manuf Technol 59:93–100CrossRefGoogle Scholar
  4. 4.
    Hadad MJ, Tawakoli T, Sadeghi MH, Sadeghi B (2012) Temperature and energy partition in minimum quantity lubrication-MQL grinding process. Int J Mach Tool Manu 54–55:10–17CrossRefGoogle Scholar
  5. 5.
    Morgan MN, Barczak L, Batako A (2012) Temperatures in fine grinding with minimum quantity lubrication (MQL). Int J Adv Manuf Technol 60:951–958CrossRefGoogle Scholar
  6. 6.
    Manimaran G, Kumar PM, Venkatasamy R (2014) Influence of cryogenic cooling on surface grinding of stainless steel 316. Cryogenics 59:76–83CrossRefGoogle Scholar
  7. 7.
    Elanchezhian J, Kumar PM, Manimaran G (2015) Grinding titanium Ti-6Al-4V alloy with electroplated cubic boron nitride wheel under cryogenic cooling. J Mech Sci Technol 29:4885–4890CrossRefGoogle Scholar
  8. 8.
    Nguyen T, Liu M, Zhang LC (2014) Cooling by sub-zero cold air jet in the grinding of a cylindrical component. Int J Adv Manuf Technol 73:341–352CrossRefGoogle Scholar
  9. 9.
    Lee PH, Lee SW (2011) Experimental characterization of micro-grinding process using compressed chilly air. Int J Mach Tool Manu 51:201–209CrossRefGoogle Scholar
  10. 10.
    Bhaskar P, Chattopadhyay AK, Chattopadhyay AB (2010) Development and performance evaluation of monolayer brazed cBN grinding wheel on bearing steel. Int J Adv Manuf Technol 48:935–944CrossRefGoogle Scholar
  11. 11.
    Chen JY, Huang H, Xu XP (2009) An experimental study on the grinding of alumina with a monolayer brazed diamond wheel. Int J Adv Manuf Technol 41:16–23CrossRefGoogle Scholar
  12. 12.
    Liang L, Quan YM, Ke ZY (2011) Investigation of tool-chip interface temperature in dry turning assisted by heat pipe cooling. Int J Adv Manuf Technol 54:35–4317CrossRefGoogle Scholar
  13. 13.
    Liang L, Quan YM (2013) Investigation of heat partition in dry turning assisted by heat pipe cooling. Int J Adv Manuf Technol 66:1931–1941CrossRefGoogle Scholar
  14. 14.
    He QS, Fu YC, Xu HJ, Ma K (2014) Investigation of a heat pipe cooling system in high-efficiency grinding. Int J Adv Manuf Technol 70:833–842CrossRefGoogle Scholar
  15. 15.
    He QS, Fu YC, Chen JJ, Zhang W (2016) Investigation on heat transfer performance of heat pipe grinding wheel in dry grinding. J Manuf Sci Eng 138:111009–1–111009–8Google Scholar
  16. 16.
    He QS, Fu YC, Xu HJ, Ma K, Chen C (2013) Development of annular heat pipe grinding wheel for high efficiency machining of TC4 titanium alloy. Acta Aeronautica Et Astronautica Sinica 34:1740–1747Google Scholar
  17. 17.
    Guo CS, Malkin S (2000) Energy partition and cooling during grinding. J Manuf Process 2:151–157CrossRefGoogle Scholar
  18. 18.
    Malkin S, Guo C (2007) Thermal analysis of grinding. CIRP Ann Manuf Techn 56:760–782CrossRefGoogle Scholar

Copyright information

© Springer-Verlag London Ltd., part of Springer Nature 2018

Authors and Affiliations

  • Qingshan He
    • 1
  • Yucan Fu
    • 2
  • Jiajia Chen
    • 2
  • Wei Zhang
    • 2
  • Zhongming Cui
    • 1
  1. 1.College of Mechanical and Electrical EngineeringHenan University of TechnologyZhengzhouChina
  2. 2.College of Mechanical and Electrical EngineeringNanjing University of Aeronautics and AstronauticsNan JingChina

Personalised recommendations