European Journal of Wood and Wood Products

, Volume 76, Issue 3, pp 889–898 | Cite as

Ultrasound grading of round Eucalyptus timber using the Brazilian standard

  • Mônica Ruy
  • Raquel Gonçalves
  • Douglas Moraes Pereira
  • Rafael Gustavo Mansini Lorensani
  • Cinthya Bertoldo
Original
  • 63 Downloads

Abstract

The structural use of round timber has been considered competitive in terms of both economics and sustainability due to the low energy consumption required for processing it. However, structural uses of wood in round and sawed forms require knowledge of wood properties, which makes the grading of these properties essential. In Brazil, an ultrasound grading standard for wood was proposed based on tests of lumber from tropical species with an average age of approximately 45 years. The objective of the present study was to evaluate whether the grades proposed by this standard could be used, either directly or by applying correction factors, to grade round timber derived from a planted Eucalyptus forest. For this evaluation, round timber with different diameters was tested using ultrasound at saturated moisture content (MC) greater than 30% and at environmental equilibrium (an MC of approximately 12%). Static bending tests were conducted only when the MC was at the environmental equilibrium (approximately 12%). Although it is necessary to validate the conclusions with a larger data set, the results indicate that due to the correlation between the diameter of round timber and its acoustic and mechanical properties, any round timber grading system must consider the diameter of the pieces. The larger the diameter of the round wood is, the greater the difference between the actual velocity in the log and the velocity expected by the grading standard that considers the stiffness.

Notes

Acknowledgements

Funding was provided by Fundação de Amparo à Pesquisa do Estado de São Paulo (Grant nos. 2012/22599-9, 2013/03449-9, 2015/05692-3) and scholarship by Conselho Nacional de Desenvolvimento Científico e Tecnológico (Grant no. 131853/2014-7).

References

  1. Amishev D, Murphy GE (2008) In-forest assessment of veneer grade Douglas-fir logs based on acoustic measurement of wood stiffness. For Prod J 58:42–47Google Scholar
  2. Bartholomeu A (2001) Classificação de peças estruturais de madeira através do ultra-som, (Ultrasound grading of wood beams), Dissertation, University of CampinasGoogle Scholar
  3. Bertoldo C (2011) Estimativa de propriedades de rigidez da madeira a partir de avaliação acústica na árvore e em toras recém abatidas. (Acoustic assessment from the tree and the freshly-felled logs for estimating wood stiffness).Thesis (Master), University of CampinasGoogle Scholar
  4. Bucur V (2006) Acoustics of Wood. Springer, BerlinGoogle Scholar
  5. Calil C Jr, Brito LD (2010) Manual de projeto e construção de estruturas com peças roliças de madeira de reflorestamento. (Manual of design and construction of structures with reforestation roundwood). University of São Paulo, São CarlosGoogle Scholar
  6. Carter P, Briggs D, Ross RJ, Wang X (2005) Acoustic testing to enhance western forest values and meet customer wood quality needs. Productivity of western forests: a forest products focus, Portland, OR: U.S. Dept. of Agriculture, Forest Service, Pacific Northwest Research Station. General technical report PNW; GTR-642, pp 121–129Google Scholar
  7. EN 408 (2010) Structural timber and glued laminated timber. Determination of some physical and mechanical properties, CEN 2010Google Scholar
  8. Gonçalves R, Costa OL (2008) Influence of moisture content in longitudinal, radial and tangential ultrasonic velocity for two Brazilian wood species. Wood Fiber Sci 40(4):580–586Google Scholar
  9. Gonçalves R, Lorensani RGM, Negreiros TO, Bertoldo C (2017) Moisture-related adjustment factor to obtain a reference ultrasonic velocity in structural lumber of plantation hardwood. Wood Mater Sci Eng.  https://doi.org/10.1080/17480272.2017.1313312 Google Scholar
  10. Íñiguez-González G, Arriaga F, Esteban M, Llana DF (2015) Reference conditions and modification factors for the standardization of nondestructive variables used in the evaluation of existing timber structures. Constr Build Mater 101(2):1166–1171CrossRefGoogle Scholar
  11. Kretschmann D, Hernandez R (2006) Grading timber and glued structural members. Primary wood processing: principles and practice, Springer, cap.10, pp 339–390Google Scholar
  12. Lobão MS, Lúcia RMD, Moreira MSS, Gomes A (2004) Caracterização das propriedades físico-mecânicas da madeira de eucalipto com diferentes densidades. (Characterization of physical and mechanical properties of Eucalyptus lumber with different specific gravities). Árvore 28(6):889–894CrossRefGoogle Scholar
  13. Lorensani RGM (2013) Classificação de peças estruturais de eucalipto utilizando ultrassom. (Mechanical classification of structural Eucalyptus pieces using ultrasound). Dissertation, University of CampinasGoogle Scholar
  14. Molina JC (2009) Relatório final da caracterização dos eucaliptos. (Final Report on the characterization of Eucalyptus). Project: environmental education center (CEAM), Votorantin Metallurgy, Forest FactoryGoogle Scholar
  15. NBR 15521 (2007) Non-destructive testing—ultrasonic testing—mechanical classification of dicotyledonous sawn wood. ABNT—Brazilian Association of Technical Standards, Rio de JaneiroGoogle Scholar
  16. NBR 16202 (2013) Treated Eucalyptus utility poles for distribution lines—requirments. ABNT—Brazilian Association of Technical Standards, Rio de JaneiroGoogle Scholar
  17. NBR 7190 (1997) Design of wooden strucutres. ABNT—Brazilian Association of Technical Standards, Rio de JaneiroGoogle Scholar
  18. Pelizan TR (2004) Estudo de propriedades mecânicas de peças roliças de eucalipto citridora utilizando a técnica de ultra-som. (Study of mechanical properties of Eucalyptus citriodora round pieces using ultrasound technique). Dissertation, University of São PauloGoogle Scholar
  19. Rais A, Pretzsch H, Van De Kuilen J (2013) Roundwood pre-grading with longitudinal acoustic waves for production of structural boards. Eur J Wood Prod 72:87–98CrossRefGoogle Scholar
  20. Ranta-Maunus A (1999) Round small-diameter timber for constructions. Final Report of Project FAIR CT-95-0091. Technical Research Centre of Finland, FinandGoogle Scholar
  21. Sakai H, Minamisawa A, Takagi K (1990) Effect of moisture content on ultrasonic velocity and attenuation in woods. Ultrasonics 28:382–385CrossRefGoogle Scholar
  22. Sandoz JL (1990) Triage et fiabilité des bois de construction: validité de la méthode ultrason (Grading and reliability of construction timber, validation of the ultrasound method). Thesis, Federal Polytechnic School of LausanneGoogle Scholar
  23. Sandoz JL (1994) Ultrasound applications to structural timber. In: pacific timber engineering conference—PTEC´94. Gold Coast, AustraliaGoogle Scholar
  24. Tsehaye A, Buchanan AH, Walker JCF (1995) Stiffness and tensile strength variation within and between radiate pine trees. J Inst Wood Sci 13:513–518Google Scholar
  25. Tsehaye A, Buchanan AH, Walker JCF (2000) Sorting of logs using acoustics. Wood Sci Technol 34:337–344CrossRefGoogle Scholar
  26. Wang X (2013) Stress wave E-rating of structural timber-size and moisture content effects. Nondestructive testing and evaluation of wood symposium, 18th. MadisonGoogle Scholar
  27. Wang X, Ross RJ, Brashaw BK, Erickson JR, Forsman JW, Pellerin R (2004) Diameter effect on stress-wave evaluation of modulus of elasticity of logs. Wood Fiber Sci 36(3):368–377Google Scholar
  28. Wang X, Carter P, Ross RJ, Brashaw BK (2007) Acoustics assessment of wood quality of raw forest materials—a path to increased profitability. For Prod J 57:6–14Google Scholar
  29. Waubke NV (1981) Grundsätzliche Untersuchungen zur Eignung der Ultraschall-Impulslaufzeitmessungen als vereinfachte und genauere Methode zur Klassifikation von Bauhölzern. (Fundamental investigations on the suitability of ultrasound pulse duration measurements as simplified and accurate method for sorting timber). Institute for Materials Science and Physics of the University of the Bundeswehr Munich, NeubibergGoogle Scholar
  30. Waubke NV (1988) Einsatz der Ultraschall-Impulslaufzeitmessung für die Sortierung von Bauhölzern. (Use of flight time measurement for sorting timber). Holzbauforschung, Innsbruck Univ. (Austria), pp 152–154Google Scholar
  31. Wolfe R, Murphy J (2005) Strength of small-diameter round and tapered bending members. For Prod J 55:50–55Google Scholar
  32. Zangiácomo AL (2007) Estudo de elementos estruturais roliços de madeira. (Study of structural round timber). Thesis, University of São PauloGoogle Scholar
  33. Zangiácomo AL, Christoforo AL, Rocco Lahr FA (2013) Módulos de elasticidade longitudinal e transversal em vigas roliças de madeira de Corymbia citriodora. (Shear and longitudinal modulus of elasticity in Corymbia citriodora round timber beams). Vértices 15:63–68CrossRefGoogle Scholar

Copyright information

© Springer-Verlag GmbH Germany, part of Springer Nature 2018

Authors and Affiliations

  1. 1.Laboratory of Nondestructive Testing, LabEND, College of Agricultural Engineering, FEAGRIUniversity of Campinas, UNICAMPCampinasBrazil

Personalised recommendations