Advertisement

Journal of Materials Science

, Volume 29, Issue 12, pp 3121–3127 | Cite as

Evaluation of advanced alumina-based ceramic tool inserts when machining high-tensile steel

  • X. S. Li
  • I. M. Low
Article

Abstract

Three types of alumina-based ceramic tools (zirconia toughened, titanium-carbide reinforced and silicon-carbide-whisker reinforced) were used to evaluate their cutting performance when machining a high-tensile steel. Experimental studies were carried out at various cutting speeds, feeds and depths of cut, in dry conditions. The cutting performance of the alumina-based ceramic tools was judged by the cutting force produced during the process of machining, by the surface roughness of the workpiece and by the wear rate of the cutting inserts. The influence of the cutting parameters (that is, the cutting speed, feed rate and depth of cut) on the cutting performance is discussed.

Keywords

Polymer Zirconia Experimental Study Surface Roughness Feed Rate 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    S. T. Buljan, and V. K. Sarin, “Cutting tool materials” (American Society for Metals, Metals Park, Ohio, 1981) p. 193.Google Scholar
  2. 2.
    M. Furakawa, O. Nakano and Y. Takashima, Int. J Refractory Hard Metals 7 (1988) 37.Google Scholar
  3. 3.
    M. Furakawa, Amer. Ceram. Soc. Bull. 62 (1983) 1384.Google Scholar
  4. 4.
    L. J. Schioler and R. N. Katz, Ceram. Eng. Sci. Proc. 6 (1985) 822.CrossRefGoogle Scholar
  5. 5.
    B. Mondal, A. B. Chattopadhyay, A. Virkar and A. Paul, Wear 156 (1992) 365.CrossRefGoogle Scholar
  6. 6.
    N. Narutaki, Y. Yamane and K. Hayashi, Annals CIRP, 40 (1991) 49.CrossRefGoogle Scholar
  7. 7.
    N. Claussen, J Amer. Ceram. Soc. 59 (1976) 49.CrossRefGoogle Scholar
  8. 8.
    A. R. Thangaraj and K. J. Weinmann, Trans. ASME J. Engng Indust. 114 (1992) 301.Google Scholar
  9. 9.
    E. R. Billman, P. K. Mehrotra, A. F. Shuster and C. W. Beeghly Amer. Ceram. Soc Bull. 67 (1988) 1016.Google Scholar
  10. 10.
    G. C. Wei and P. F. Becher, ibid. 64 (1985) 296.Google Scholar
  11. 11.
    J. Vigneau, P. Bordel and A. Leonard, Annals CIRP 36 (1987) 13.CrossRefGoogle Scholar
  12. 12.
    X. S. Li, I. M. Low, J. G. Wager, D. S. Perera and B. H. O'Connor, Proceedings of the Internatioal Conference on Advanced Composites, Fabrication, Processing, Properties, Performance, Design and Applications, 15–19 February 1993, University of Wollongong, Australia, in press.Google Scholar
  13. 13.
    X. S. Li and I. M. Low, J. Mater. Sci. Lett., in press.Google Scholar

Copyright information

© Chapman & Hall 1994

Authors and Affiliations

  • X. S. Li
    • 1
  • I. M. Low
    • 1
  1. 1.Materials Research Group, School of Physical SciencesCurtin University of TechnologyPerthAustralia

Personalised recommendations