Advertisement

Journal of Materials Science

, Volume 29, Issue 24, pp 6453–6457 | Cite as

Zone melting-refining in Bi-Pb-Sr-Ca-Cu-O superconductor prepared through the sol-gel method

  • T. V. Mani
  • A. D. Damodaran
  • K. G. K. Warrier
Papers

Abstract

A zone melting-refining technique, with a horizontal sample-holding pattern for incorporating grain orientation in sintered bismuth-based superconductor (BPSCCO) is presented. Acrylate precursor-derived BPSCCO powder was uniaxially compacted into strips of 60 mm×10 mm ×2mm and sintered at 845°C for 20 h to obtain 90% density. These strips were zone melted in a three-zone furnace which had an independent temperature control system for each zone. The grain orientation in the sample was studied by scanning electron microscopy and X-ray diffraction. In the case of a BPSCCO-Ag (5%) composite, the silver was seen to flow along the intergrannular boundaries of the BPSCCO grains. The present technique is an easy and fast method to introduce orientation of grains with large aspect ratio into sintered BPSCCO or Ag-BPSCCO composite under partial melting-refining conditions. The possibility of extending the present technique to silver-sheathed wire and tapes is also indicated.

Keywords

Polymer Electron Microscopy Scanning Electron Microscopy Furnace Control System 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    H. Maeda, Y. Tanaka, M. Fukutomi and T. Asano, Jpn J. Appl. Phys. 27 (1988) L 209.CrossRefGoogle Scholar
  2. 2.
    M. K. Wu, J. R. Ashburn, C. J. Torng, P. H. Hor, R. L. Meng, L. Gao, Z. J. Huang, Y. Q. Wang and C. W. Chu, Phys. Rev. Lett. 58 (1987) 908.CrossRefGoogle Scholar
  3. 3.
    Z. Z. Sheng and A. M. Herman, Nature 332 (1988) 55.CrossRefGoogle Scholar
  4. 4.
    M. Takano, J. Takad, K. Oda, H. Kitaguchi, Y. Miura, Y. Ikeda, Y. Tomii and H. Mazaki, Jpn J. Appl. Phys. 27 (1988) L1041.CrossRefGoogle Scholar
  5. 5.
    T. V. Mani, H. K. Varma, K. G. K. Warrier and A. D. Damodaran, Br. Ceram. Trans. J. 91 (1992) 121.Google Scholar
  6. 6.
    K. Tanaka, A. Nozue and K. Kamiya, J. Mater. Sci. 25 (1990) 3551.CrossRefGoogle Scholar
  7. 7.
    T. V. Mani, H. K. Varma, A. D. Damodaran and K. G. K. Warrier, J. Am. Ceram. Soc., submitted.Google Scholar
  8. 8.
    J. Sungo, J. Metals 43 (1991) 7.Google Scholar
  9. 9.
    K. H. Sandhage, G. N. Riley Jr and W. L. Carter, ibid. 43 (1991) 21.Google Scholar
  10. 10.
    P. J. McGinn, W. Chen and N. Zhu, ibid. 43 (1991) 26.Google Scholar
  11. 11.
    H. Kumakura, K. Togano and H. Maeda, in “International Conference on Superconductivity-ICSC”, edited by S. K. Joshi, C. N. R. Rao and S. V. Subramanyan, 10–14 January 1990, Bangalore, India (World Scientific, Singapore 1990) p. 226.Google Scholar
  12. 12.
    P. McGinn, W. Chen, and N. Zhu, in “High Temperature Superconducting Compounds II”, edited by S. H. Wang, A. D. Gupta and R. Laibowitz (The Minerals, Metals and Materials Society, Warrendale PA, 1990) p. 71.Google Scholar
  13. 13.
    H. K. Varma, K. G. K. Warrier, V. A. Kumar, T. V. Mani, S. G. K. Pillai, and A. D. Damodaran, Jpn J. Appl. Phys. 31 (1992) L543.CrossRefGoogle Scholar
  14. 14.
    Winnie Wong-Ng, C. K. Chiang, S. W. Freiman, L. P. Cook and M. D. Hill, Am. Ceram. Soc. Bull. 71 (1992) 1261.Google Scholar

Copyright information

© Chapman & Hall 1994

Authors and Affiliations

  • T. V. Mani
    • 1
  • A. D. Damodaran
    • 1
  • K. G. K. Warrier
    • 1
  1. 1.Regional Research Laboratory (CSIR)TrivandrumIndia

Personalised recommendations