1. Physical background and simulation of creep in steels

   • Stan T. Mandziej

   Research Paper 01 May 2020 Pages: 1119 - 1134

   

2. Microstructure investigation of duplex stainless steel welds using arc heat treatment technique

   • Andrea Putz
   • Vahid A. Hosseini
   • Norbert Enzinger

   Research Paper Open access 08 May 2020 Pages: 1135 - 1147

   

3. Effect of welding variables on GTAW arc stagnation pressure

   • Gabriel de Simas Asquel
   • Ana Paula Storto Bittencourt
   • Tiago Vieira da Cunha

   Research Paper 24 May 2020 Pages: 1149 - 1160

   

4. Effects of residual stress by EB welds on assessment of crack arrest temperature (CAT)

   • Chiyomi Iwatake
   • Masahito Kaneko
   • Tomoya Kawabata

   Research Paper 03 June 2020 Pages: 1161 - 1174

   

5. Influence of mill scale on weld bead geometry and thermal cycle during GTA welding of high-strength steels

   • Rahul Sharma
   • Uwe Reisgen

   Research Paper Open access 05 May 2020 Pages: 1175 - 1183

   

6. Numerical investigation of CTOD estimation methods for laser welds

   • Yasuhito Takashima
   • Chendong Shao
   • Fumiyoshi Minami

   Research Paper 09 May 2020 Pages: 1185 - 1193

   

7. Residual stresses in thermite welded rails: significance of additional forging

   • B. Lennart Josefson
   • R. Bisschop
   • J. Hantusch

   Research Paper Open access 17 May 2020 Pages: 1195 - 1212

   

8. EBSD analysis of microstructures and mechanical properties of softened zones in X60 reeled-pipeline welded joint after cyclic plastic deformation

   • Yuanbo Jiang
   • Chengning Li
   • Jiangcheng Liu

   Research Paper 12 May 2020 Pages: 1213 - 1225

   

9. Laser transmission welding of absorber-free semi-crystalline polypropylene by using a quasi-simultaneous irradiation strategy

   • Nam-Phong Nguyen
   • Stefan Behrens
   • Arnold Gillner

   Research Paper Open access 13 May 2020 Pages: 1227 - 1235

   

10. Comparison of effect of shot-peening with HFMI treatment or use of LTT consumables on fatigue strength of 1300 MPa yield strength steel weldments

    • Ebrahim Harati
    • Lars-Erik Svensson
    • Leif Karlsson

    Research Paper Open access 12 May 2020 Pages: 1237 - 1244

    

11. Effect of increased yield strength, R-ratio, and plate thickness on the fatigue resistance of high-frequency mechanical impact (HFMI)–treated steel joints

    • M. Leitner
    • Z. Barsoum

    Research Paper Open access 13 May 2020 Pages: 1245 - 1259

    

12. Simulation on Ti-based filler and vacuum brazing for TA15 alloy

    • Yongjuan Jing
    • Huaping Xiong
    • Yaoyong Cheng

    Research Paper 12 May 2020 Pages: 1261 - 1268

    

13. On the distortion and warping of cantilever beams with hollow section

    • Timo Björk
    • Antti Ahola
    • Tuomas Skriko

    Research Paper Open access 09 May 2020 Pages: 1269 - 1278

    

14. Detailed investigation of adhesive fillet tubular T-joint of laminated FRP composite tube under axial compressive load

    • Kundan Bharti
    • L.A. Kumaraswamidhas
    • R.R. Das

    Research Paper 06 May 2020 Pages: 1279 - 1292

    

15. Fatigue strength of transverse attachment steel joints with single-sided arc weld using low transformation temperature welding consumable

    • Takeshi Hanji
    • Kazuo Tateishi
    • Toshio Takebuchi

    Research Paper 18 May 2020 Pages: 1293 - 1301

    

16. Correction to: The impact of production-dependent geometric properties on fatigue-relevant stresses in aser-welded corrugated core steel sandwich panels

    • Peter Nilsson
    • Joakim Hedegård
    • Seyed Rasoul Atashipour

    Correction Open access 15 May 2020 Pages: 1303 - 1303